I got some coilovers installed last night, they are ksports. i have them on fairly low height as of now but i have noticed every time I hit bumps, I hear a kthunk (metal hitting metal noise) from my front driver side. is it from the coilover nuts itself or something wrong with my control arm? the sound ONLY comes from the front DRIVER side.
View 4 RepliesI have a 2003 Toyota Solara 4 cyl. auto. transmission. I recently had the head replaced. Now it is making a metal on metal sound near the drivers side of the engine. It makes the sound during idle, when I change gears, and the sound increases when I rev the engine. What could it be?
View 8 RepliesSometimes when closing either the front driver or passenger door, it seems as though the door is not closing properly and it sounds like the latches are striking metal against metal. The doors always close and the noise does not occur all the time, in fact it occurs on a very seldom basis. The noise is very annoying and definitely does not sound right. I can not repeat the problem at will and I fear the dealer will not be able to locaate, unless it happens just as they close the door. The doors do close tight, but the sound is awful (sharp metal hitting metal sound).
View 2 RepliesI have a 2007 hyundai sonata, this car is my daily driver. I put 180 miles on it a day around trip. Currently has 180,200 miles on it. Last Friday on my trip home when i turned right I heard a metal on metal sound. I slowed down went straight and it went away. Talked to a few people and I think it may be the wheel bearing. Even if I hit a road reflector it starts up. It's the front left wheel. Get on the breaks it goes away.
So my question is... Wheel bearing??? And can I replace the whole hub and fix the problem or do I have to try and press the bearing out?
A year ago I heard occasional metal grinding noise coming from the front, sounding like front driver side. Sounded like CV joints that I heard before. The mechanic said it's transfer case/transmission problem, so I replaced the transmission but the noise came back a few days later. The mechanic said to drive it for a while and the noise may go away, if getting worse he can fix it since it has 2-year warranty.
Now a year later the noise becomes predicable and easily reproducible, I went back and asked them to check. They said it may be passenger side axle. I am feeling being manipulated.
What we have is a 2011 F-350 with the ambulance package (obviously) and it has started making a very annoying sound from the front end. It has been into two different Ford Dealerships and they have not been able to remedy this issue. What happens is, when we are backing and turning, the front end makes a bad metal on metal grinding noise. When going straight down the road no issue just turning while backing. I know this is an ambulance and has the ambulance package but I think from the cab forward should just be all ford right?
View 2 RepliesI recently worked on a 2006 with 140K miles that presented with the following symptoms:
The hybrid battery was at 1 bar; the ICE would not start; the car was in Ready, but there were no codes. As I let it roll off the flatbed wrecker in Neutral, it felt lumpy. If you have ever pushed a car (or run out of gas in one) with a manual transmission that was in a high gear, engine off, it felt just like that.
I popped the hood and could see that the engine crank was turning while the car was being pushed in Neutral. What else turns with the wheels? MG2, or more specifically, the MG2 ring gear. What is the only way that the wheels could turn the ICE crank? The planetary carrier pinions were locked to the ring gear.
Surprisingly, while I was looking at things, it did manage to start the ICE pushing it around must have freed the carrier pinions, so I let it charge the hybrid battery. It was basically the worst metal-to-metal noise that I have ever heard! I pulled the drain plug and saw about a teaspoonful of large metal chips on the magnet. The fluid condition itself was very good, not the black factory fill that I am used to seeing come out.
My 2011 2.4l Sonata made a metal on metal sound suddenly the other day. About 4 days ago, I drove about 2 hours away from where I live, Mostly highway, about 80mph to a go kart race. Got out of the car for a while and came back in and was pulling away to run the store and as i started to approach the first stop sign maybe 500-600 ft from where i was parked, i heard a bad metal on metal sound, came to a complete stop at the sign and it stopped. Went back to the race after driving to the store about 5 miles away.
Got in the car to leave and same thing, just to the stop sign 500-600ft away. Drove home like i said mostly highway, and didn't hear a thing. Today, about 4 days later, I drove to Chicago O'hare airport, about 30min away, and it was fine the whole way there. However on the way back, after about 20-25min, I heard it again. So I came to complete stop as I was forced to by a traffic light as I was taking my exit off the highway, and It started making that sound again. So i came to a complete stop at the light and started moving again when it turned green and couldn't heard a thing.
I replace my brake pads and rotors in the fall of 2015 with EBC parts. Now almost 13,000 miles later, I started hearing grinding and metal-on-metal contact in the front. So I went out and got PowerStop pads to replace the EBC (EBC had way too much brake dust). I took off the front wheels and noticed that the DF pads had about 1/32 left on them, ok I guess its time to change them out. Onto the PF pads, I find that there is almost no material left, in fact I could scrap off what was left of the material. I decided to do a rotation while I am at it and noticed that the rear brake pads on both sides look like I never used them!! Is it really that possible to have 2 stuck calipers, both on the rear at the same time?
View 2 RepliesAt 75K my passenger side rear brakes were making metal on metal sound. I was really surprised as I have always learned that the front brakes take 80% of load and they always go out before the backs. So I took the wheel off and sure enough the pads were metal on metal. Changed everything out. (new rotors). I then went over to the driver side rear brake. Looks brand new. The pistons were barely out. I figured this caliper is bad. (I haven't change yet)
When I drive I can hear a very faint metal on metal sound when I brake. VERY FAINT. So with 75K miles on I figure the front brakes are due. Today I took the wheels off and inspected them. Tons of pad left on both of them. If I didn't know better I would say a brake job had been done very recently. (I've owned the car new so I know they have not had a brake job) However after reading many articles on this site I found a thread where one user said he was changing his front brakes for the first time with 110K on them and the pads still had 10K left in them. So the fact that my front pads are still pristine at 75K may not be a big deal (or not as big as I thought. Also I am not hard on brakes.)
However I'm not sure what is going on. Why would the passenger rear brake be metal on metal at 75K and the three other pads are like new. Is the passenger rear the only one working (or working much harder than the others) meaning the other three are bad? Or is the rear passenger bad and the other three are good? I have a working knowledge of cars but I am by no means a mechanic.
I have a question about my C Four with 16" wheels. When the steering wheel goes all the way to a stop there is a thunk that feels like metal on metal. It is like there is no rubber bump stops. If this is normal. I am used to cars that have a nice cushioned bump at the steering limits.
View 1 RepliesHonda Accord 2005 ... Just bought a new used car. All seems ok, but I have two problems.
(1) when not moving, i have slop in the steering and I can hear metal on metal contact when I turn the steering wheel. I pulled the tire and with basically no force I can move the rotor back and forth by hand. what it is and how to fix it?
(2) when braking, it appears that the front left pad sticks. Pads are not excessively worn down. Can't figure out how to get to the caliper pins ( thought they might be sticking).
Could the two be related?
When driving slow, and hit little bumps it sounds like its a loose exhaust, or something metal is loose. The sound is coming from the drivers side. What it might be, or had the same problem? Really don't want to take it all the way to the dealer.
View 14 RepliesI commute 180 miles a day, 6 days a week. I noticed metal on metal grinding noise(more noticeable) at high speed above 75mph especially on asphalt road. I'm sure noise is there at low speed but not enough to notice. My car has 50,000 miles. Tires? Electric motor?
View 7 RepliesMy Elantra's HVAC fan has always been a quiet thing, even on 3.....we won't mention level 4 and the fact it sounds like a 747 at takeoff.
I kid you not, the very evening I hit 60,000 miles and the general warranty expired, the blower motor started making noise like it was throwing a bearing and definitely sounded like some light metal-on-metal rubbing. After I became irritated at this, the noise went away and didn't come back until just a few weeks ago. I could make it stop by smacking on the bottom of the fan assembly a few times but I want a more permanent solution.
Tonight I dropped the blower out which was stupid easy except for the fact you're upside down in the dark with your head in a hole. But three screws and an electrical connector later, I dropped the assembly to find no serviceable components. I mentioned this to friend of mine who's into Volvos suggested spraying some lithium grease on the hub of the blower and letting it run long enough to quiet it down. I'll do this over the next few days and report back but part of me thinks a new blower may be in my future.
I have a base v6. When I turn the steering wheel (for example, to make a left turn), it sounds like there is metal-on-metal rubbing. The wheel is not extended (turned all the way til it stops)...
View 2 RepliesI have an '02 Taurus. For the last year or so it has intermittently produced a metal on metal grinding noise while failing to start up. I'm told this is due to teeth being missing on the flywheel between the starter and the transmission. It's taken as many as six tries to get the car going. But the car has always started in the end.
My questions are: Is the problem flywheel worth replacing at this point at this price? Is it likely to fail totally any time soon?
Also, might the March '09 replacement starter be implicated?
I have intermittent metal on metal grinding noise. Seems to happen when I am at highway speed. Seems to go away when I put it on 4 wheel drive or slow way down. On one occasion though, the grinding noise did not stop even after putting on 4 wheel drive - had to stop completely before it went away (did not come back after I drove off again). Diagnostics so far....
Unhooked the vacuum lines on passenger side actuator and hooked up vacuum gauge. Vacuum held at 20 psi and drops and raises slightly as the truck is being revved. Takes about 10 seconds for vacuum to drop to zero once truck is stopped. Putting it on 4 wheel drive drops it to zero immediately. Exact same scenario on the passenger side.
This leads me to believe my IWE solenoid is ok. So also my check valves. Next opportunity I get, I will raise one wheel, remove the vacuum line on that wheel and apply vacuum with my pump. Want to see if it will turn my half shaft.
2004 F150 FX4 ....
My father's 1997 F150 with the 4.6 two wheel drive, has me stumped again. I have a lot of mechanic knowledge but this one has got me wondering whats going on. Here is the run down. When you are driving down the road, it rides just fine and makes no noises from 0-20 MPH, after about 25 to 35 mph it makes like a metal on metal noise that is coming from the rear, and forces the truck to slow down, when you try to accelerate through this problem it has a bad bang and it wont allow you to speed up anymore, it does not seem like a brake issue (but I could be wrong) since it does not actually pull to one side or the other.
It seems like an equal force trying to stop the truck. I have heard rear ends that were going out and they make clunk noises or whirring noises etc, but its still some what driveable. I have checked the rear end oil and it does have oil in it, and its probably about an inch from the full level (but that shouldnt cause this issue im sure). My father wants a definite answer before we start tearing this thing apart to try and fix it. Since its mostly used to take trash off, and also get the kids down the dirt road to the bus stop.
When driving in my parking garage, I can hear a slight metal on metal noise. An extreme example would be sharpening a knife on a sharpener, its not as loud or predominate.
-I've checked the lugs, they are secure.
Car has springs and spacers.
I have a 2011 Prius with about 32K miles on it. I've been hearing light metal on metal grinding noise for a few days now. So I decided to take it to a stealership and they told me my ceramic pads and brake rotors both need to be replaced for all 4 wheels. I thought Prius brakes don't need to be replaced for 100K miles.
View 7 Replies