I have a 2008 2.4 lots of movement in front sway bar so trying to change bushing. Have it on a hoist and still can't get to the rear bolts to remove them have 3 different socket sets power ratchet and different spanner sets. Is there a DIY write up on this or pictures as I have not been able to find one?
View 3 RepliesTrying to change the front sway bar bushing with a PU version? Does it improve handling and steering feedback?
View 1 Replies2002 ford explorer XLT. Here is a pic of the issue. have a broken right front sway bar link that has broken on the top however the bottom is still attached. I am unable to remove it. The top portion is gone and I am unable to grip what is left enough to loosen the bottom bolt. I have tried pliers as well as vice grips to keep it from spinning as I loosen the bottom bolt. Nothing has worked. The outside plastic OEM piece is stuck in there so well I am unable to break that loose either. I have sprayed PB blaster hoping to loosen things up but here I am writing this.
View 4 RepliesMy Ex has a 4-inck Sky Jacker lift and I need to replace one of the sway bar end link bushing. Is the bushing size same as the stock ones? Need to know so I can order the right ones. What is the Energy Suspension part#....
View 1 RepliesI have a friend with an 01 f250 super duty who needs to replace sway bar bushings.
View 6 Replies2016 2L Escape. My question is this. I've had the vehicle for the past 12 months and each rainy season here in California, I admit its not often we get rain but we have it now and its about time. Anyway while driving in wet conditions I get a squeak from what I think is the right rear sway bushing and it only happens during starting out, stopping and parking lot speed bumps all at low speed. No noise at when driving at speed. I've had it to the dealer 3 x to fix, they grease the bushing and it seems ok for awhile but not he permanent fix I was hoping for.
View 1 RepliesCar: 02 Passat GLX 4motion V6 AWD
I'm in process of replacing the rear strut and I can't remove the way bar link bolt out. It is really tight into the inner rubber and it won't buzz. The bolt sits in a way that I can't use a hammer.
I read a reference to the front brake caliper bracket bolts being one time use torque to yield and must be replaced every time they are loosened. Is this true?
This is on my 06 F-350 in my Sig.
How to remove a crankshaft pulley like this one? It doesn't have any holes for bolts, to hold some soft of breaker bar in place.
Pulley.JPG ....
I want to plasti dip the emblem and the chrome piece on my hood and around my grill. what is the best way to do it? How can i remove it so i can easily paint it?
View 4 RepliesWhat size socket I need to remove the driveaxle hub bolts from this car? I can see the bolts are considerably larger than the socket I have for my Ford Tauruses, and I would like to eliminate the guess work before I go to carquest to get the proper socket. Unfortunately bringing the car to the store and trying sockets until I get one that fits is not an option, since the car is not running right now.
View 3 RepliesI'm pulling my control arms to replace the bushings (they were completely split) and I'm trying to get the right one off. How the heck did you get the boot out on the front passenger side?! See pics. The bolt jams right up to the oil pan. The only way I see it is to remove the pan. Is this right?!?!
View 6 RepliesFor some months, I've heard squeaking noise from passenger side suspension. Sound like it's from shock & spring on bump road.
This video sound is very similar : Squeaking Noise, Front Driver Side - YouTube ...
I looked at my suspension. and found rubber bushing is broken. Driver's side bushing is normal.
Is this noise related to the broken bushing?
Is it easy to replace the rubber by myself?
A guy said ATP AT-205 reseal will fix this noise in Youtube video. Is it true?
How To Fix Squeaks In Your Car - YouTube ....
I have a 2002 echo, and I need some work done on it. I'm pretty sure that my engine mounts are bad, and I know that my front bushings are shot. What should I expect to pay for the bushings/mounts to be replaced? Also, how do I know if my engine mounts are bad? Note that I am a college student living on campus, so doing the bushings will be next to impossible.
View 2 RepliesI'm working on a couple of repairs and have encountered a few questions:
1. Are the bolts supposed to come out of the top of the end link? Mine don't so I don't know if that's the way it is or mine are so far gone that they are frozen in the sleeve. My poly bushing kit does not have any new bolts so I'm hesitant to lay into it with a 10 ton press and ruin the bolts (I don't know how much they are from Ford to buy or if I can even buy them).
2. HPO rail plug. I'm removing my HPX as I'm tired of it leaking (hopefully when my HPOP comes back as a T500 I won't need it anyway). I've seen 33 ft-lbs and 96 ft-lbs. As I go towards the 96 ft-lbs it feels like I'm going to strip the threads out so I backed off and they are at 33 ft-lbs now (I don't need that headache and my wife would go through the roof). I got the ones from Riffraff as I misplaced the ones I took off 8 years ago (go figure). The HPO line connections to the head (or pump for the matter) are 19 ft-lbs. I use Loc-Tite on those but both have an o-ring (which provides most of the seal) so I'm not to keen on gronking the rail plug.
3. I'm also replacing both HPOP gaskets. I know that the HPOP and reservoir mounting bolts are 18 ft-lbs (from Ziggy. in the tech sticky) but is there a spec for the cover bolts too? I know the gasket provides the seal but I'd like to make sure that the force is distributed evenly across the gasket (Sous isn't the only OCD person around).
Hopefully this fixes most to all my oil leaks (still have to tackle the oil cooler). The valley is covered (as well as the front of the reservoir) and there is a lot of weepage on the paper towel test. There are years of buildup everywhere and will take a few tries and several cases of Simple Green to see the metal again.
The driver side front body mount bushing on my 2014 is gone which has the grill sitting on the bumper. I started to replace it, but the bolt is sized to the nut. ran off about 1/2 inch and that is it, it will not tighten or loosen anymore.
I cut the head off the bolt, but can not get the body high enough to remove the old bushing so i can cut the nut off flush with the rad support. Now I am trying to get the air filter box out so i can cut the top of the "nut cage" off to remove the bolt and nut out the top. but i can not figure out how it is held in.
I have the intake disconnected and the filter hat off, overflow tank hose disconnected, and two bolts holding the whole thing to the fender out, but it will still not budge. What am I missing here?
So I have to replace them since I have this rattling in the rear and my mechanic has diagnosed it to be the rear bushings...
View 1 RepliesI just installed rear sway bar & links, this made a world of difference in the way the car handles as soon as I made the first turn I could feel the difference in the car it definitely corners flatter, the install only took about an hour did it in the driveway on ramps, I installed the kia sway bar 555102T000 the bar is 18.3 mm while the stock one is only 15mm I included some pics...
View 8 RepliesCan the hellwig sway bar links will work with an oem sway bar? I need new ones and figured why replace with something I know will fail early...
View 3 RepliesMy Tig has been doing a sharp clunk (single) for awhile when going a bit too fast over speed bumps. I just ignored it, as I'm not flying over bumps regularly and I had just replaced the OEM struts all around. Now when accelerating over 60 kph the car has a side to side shimmy. Also when compressing or unloading the front end suddenly, like with dips on the road, makes it clunk. Checking the various suspension components?
View 6 RepliesI'm going to have my front sway bar mounting bushings replaced with poly bushings next week. Shop said they wanted to order 19mm bushings for my car, but everything I see online says its a 21mm bushing. Which is correct? It's a 2004 R32.
View 1 Replies