Sonata NF (2006-10) :: Grinding Noise Only Occur When Car Is Moving
Jan 22, 2012
Have a '06 V6 GLS w/ approx 105K miles. About a week ago I started hearing a noise. The noise sounds a lot like a brake pad wear indicator, metal grinding on metal. However, the noise does not seem to be related to use of the brakes. The noise only occurs when the car is moving. It is intermittent. Comes from the front of the car. Seems to usually occur when making a sweeping or gentle right turn. Speed does not seem to matter - can be going 20 to 60 mph. Noise will last from less than a second to as much as 5 to 10 seconds and then goes away.
I have taken a cursory look at the crankshaft damper pulley and it appears to be ok...
View 12 Replies
Advertisement
Just put on eibachs and car is randomly making a grinding noise when slowly accelerating or braking.. Also noticing a fairly loud clicking noise when going in reverse. The noise isn't consistent and seems to happen more right after startup. I haven't gotten the alignment done yet and was wondering if this could be the problem. Will try and post a video soon.
View 8 Replies
I just bought a 2006 Sonata LX V6 a few days ago and in almost every way it seems like a great car. My '08 GLS V6 which gave me 150k great miles got totaled in November, which really sucks, but I wanted to find another '06-'08 V6. I noticed when I started it for the test drive that the car made a bit of a grinding noise on start up. I didn't think much of it and figured that the warranty from the dealership would cover any problems.(I probably should've checked earlier, but the dealership's warranty only covers cam and lifter noise and engine failure) After I looked into the issue more, I found out that it is a fairly common problem on the early 3.3's with the timing chain tensioners. I'm pretty concerned based on just the nature of the repairs and the cost I've seen for them.
I'm the third owner so the 5 year/60k warranty is expired, but I know there is a TSB out for the issue. I can't find the TSB anywhere but I've heard to have it repaired the car has to make the noise on start, sit 10 minutes, and make the noise again. If it does, the oil needs to be changed and the test repeated again. Since I'm running Hyundai 5W-20 and an OEM filter already, I tried the test on my own. It made the noise on start, sat 10 minutes, and made it again. It is only for a couple seconds, but it's still concerning to me. I guess what I'm trying to ask is if what I've described is covered under the TSB. I really don't wanna have to worry about something like that right now, so my next question is whether the issue I have is detrimental to the motor. My worst fear would be to have the chain jump a cog on the cam gear and slam valves into pistons.
View 11 Replies
Need to determine the noise before I took the vehicle in to be serviced. I don't know if I would necessarily describe this as grinding...to me it doesn't sound like metal on metal..but it's not normal.
Only happens on a cold startup, and even then it hasn't been 100% of the time...probably 80% of the time though.
2007 Hyundai Sonata - Startup Noise - YouTube
I found this thread, Grinding Sound On Statup but not sure it's the same issue. This just started. Vehicle has 150K miles on it.
View 2 Replies
I have a 2009 Hyundai sonata, 2.4, 5 speed manual, gls, when I press down on clutch whether from a stop or when shifting, I get a loud grinding noise and the radio goes dead at same time!, I know it is the starter attempting to "engage", at least that's what I believe it to be, it also "'starts "from, the "on " position when I press on clutch.
View 8 Replies
A few days ago, my Sonata 2006 LX started making weird noises when driving at low speeds. The noise comes from the front driver's side area, they are not affected by steering or going over bumps. Usually get less intense when I accelerate or brake. At speeds around 5 mph, the noise is grinding and pretty loud. At higher speeds, it's more like banging and it's frequency increases with the speed. There was no effect other than the noise, but the last day at higher speeds, I can feel with the steering wheel a little vibration sometimes from the banging.
I've been having tough times renting a car during the weekend and I still drive on short distances, but I'm afraid it could be a safety issue or that I can be making things much worse to repair. The noises got worse since the beginning, but I don't think they are getting any worse anymore.
View 3 Replies
Long story..couple months ago while coming home my 08 Sonata 2.4L manual 84,000 miles...started making this grinding noise and would stop when I pressed the clutch in and then sounded like something was grinding near the passenger front wheel.. well I get it home and the next morning my husband and I ride up the road so he can hear it.. was going to take it to the shop but it stopped and ran just fine till the other day.. crank the car and its fine.. once it gets warmed up and a few miles down the road it makes a knocking noise...but only when I let off the gas or idling .. even pressing on the gas just a tiny bit made it stop (even tried in while parked in the driveway with the hood up to make sure the engine wasn't just drowning it out) well I took it to the local dealership today and they said it was the flywheel and that it and the clutch and bearing needed to be replaced..
View 3 Replies
I am now getting a grinding noise when I shift from first to second gear. It sounds like the two metals rubbing each other. Its not happening all the time, but for the past two days a bit frequently
I had reported this grinding noise when I turn left a month back. Was thinking because of my worn out tyres, but apparently not.
View 8 Replies
I just got the car back from repairs, there was a loud grinding noise coming from the left side of the engine. It turned out the whole rack and pinion setup was pouring out fluids and needed to be completely replaced also while it was in there they checked out an oil leak which ended up being the front valve cover and replaced a dead O2 sensor. The car has 99,300 miles
View 6 Replies
I noticed yesterday a sound, like a grinding sound, *sometimes* as I apply the brakes to stop. I'm at 68k. The noise only happens when the brakes are applied so I suspect there is an issue with my brakes again.
Some BACKGROUND info: At around 60k (or 8 months ago roughly), the front pads were replaced after the brakes were squealing and a pulsating brake pedal when stopping. The pads were replaced by a dealer. In addition, both front/rear rotors were turned at the same time. Rear pads had 40% at the time and were not replaced.
Some weeks later the pulsation came back and I went back again and they machined them again. For this current issue I was thinking about taking the car to someplace local (not a dealer) and getting a free brake evaluation of what is going on.
I'm also concerned that all this machining the dealer did to eliminate the pulsation may have decreased the life of the rotors and perhaps they need replacement now.
View 3 Replies
I have a very slight grinding noise coming from the PS pulley area. Its possibly bearing noise although its hard to say. Is there a specific torque requirement. Any good parts...
View 1 Replies
I'm at my place in Florida 1,000 miles from home, and when I started the car in a mall parking lot, there was some grinding metallic noise for a few seconds and I couldn't get it into first or reverse and the clutch pedal was way down. I was able to get going in 2nd and eventually the clutch was back to normal and I could get 1st and R. What happened? Broke some fingers in the pressure plate? Seems to run fine now but have a 1,000 mile ride ahead in the morning.
View 1 Replies
I heard a grinding noise from one of my rear wheels. After investigating, I saw that the OUTER pad was worn down all the way. I had only driven 15K and it had not been very long so I did not expect this. I also didn't hear the warning tabs as the they are on the inner pad and it had not worn down enough. I checked the caliper slide bolts and they were gliding freely. I checked under the boots and there was still grease in there.
My old pads had only been worn to 30%-50% so I installed those on for now. When I compressed the piston, I had a hard time getting it started and had to apply a bit of force with the C-clamp, but then it compressed without the need for much force. When I put the pads in, it was pretty hard to get them into the clips. the inner one required me to press pretty hard with my hand, the outer one was so tight, I had to use the c clamp to get it all the way up to the rotor.
I'm wondering what the cause may be. Are there some typical causes for why the outer pad may wear faster? I would think if the caliper bolts were stuck, that would do it, but they move freely? could it just be that the pad is too tight on the slider? How might I fix that? I tried filing them down a little but that obviously wasn't enough.
Also, now the pads on the right and left are uneven and the rotor on the right isnt smooth anymore. Should I go ahead and change out the pads and that rotor? Does uneven pads or a rough rotor affect the effectiveness of the brakes significantly? They are the rear brakes so I would think there is less of an impact. I know that uneven pads and a rough rotor will cause them to wear faster, but if I need to replace them anyways, I might as well wait til they wear down more.
View 17 Replies
This noise started this week. Grinding when I take my foot off the brake when in park and parking brake set. What is causing it?
A guy at work said brakes. The front brake pads were replaced last year. Original rear.
Just over 90,000 miles.
View 3 Replies
I have a 2007 Sonata 3.3 V6 GLS (CDN model) with 102k km (63K miles). Recently, I am noticing a rotational metal-like grinding noise from the front left wheel / engine area when engaging in hard right and left turns - usually a long looped highway on-ramp or sharp 90 degree turns. The interesting thing is this only happens when I am accelerating through the turns - when I left off the gas and cruise I don't hear it anymore.
On the side, I am also getting a single clunk noise when shifting from Park to Drive and vice versa from the same area (front left wheel) - not sure if this is related (i.e. if this is all related to a failing CV joint or wheel bearing).
View 2 Replies
[URL] ....
2004 Honda Accord LX
Engine: 2.4 L
119,400-ish miles
See above video link.
I've been having this odd sound occur while I accelerate - sort of like a grinding sound (about 7 seconds into the video). It might be a bit difficult to hear over the other sound coming from my car... It occurs a lot more frequently when it's cold, when I'm accelerating, and when I am turning while I accelerate.
Also, the more obvious noise that occurs throughout the entirety of the video just began today. It does not occur while I'm stopped and it began when I stepped on the brake a little harder than usual...
View 1 Replies
So I put in new rotors and pads and everytime the car is backing up I get a weird grinding or squealing noise. I've driven the cars for hundreds of miles and this still happens. This only happens when going backwards. Anything to try???
View 4 Replies
I have an 07 Sonata with the 4 cyl engine. Problem is the A/c only cools when car is moving. Took car to mechanic and was told Radiator fan bad, so I replaced and still have same problem. Fan still will not operate. Fuses checked and everything ok there. Found the Fan control module under left front headlight to be cracked and broke from wreck a couple of years ago so I ordered that and replaced it. Still the A/C only works while driving. Come to a stop and it starts blowing warm air.
View 3 Replies
I had to stop quick today. My ice water spilled into the gear shift lever. A mile down the road my rpms went up high and the car barely moving.
2006 Hyundai Sonata...
View 3 Replies
So for a couple months now, my ride has been making some weird noises.
When I start the car up after anything longer than a couple hours of use, it sounds as if I have a piece of loose metal banging/moving around. I hear it sporadically on shifting through the gears, and when I'm at a stop.
Car has been in to the dealer three times, and I took the foreman on a test drive...of course it wouldn't make the sound at all.
I took a look under the hood today and noticed that the coolant level is low...filling it back up tomorrow. That got me thinking about the transmission fluid....I looked and looked, and can't find the transmission dipstick anywhere.
Any clue where I can find some way to check the level?
View 6 Replies
I have a 2008 Hyundai Sonata GLS 2.4L with 131,000 miles on it. When I accelerate from a stop, there is a buzzing/rattling/grinding noise coming from the engine bay of my car. It's really hard to describe, there is a definite buzzing sound, but also almost like there is a bolt rattling around and banging into things. This only happens for a couple of seconds. It also seems to be worse when I'm accelerating up hill. If I accelerate slowly from a stop, the noise does not occur, and it also does not occur if I accelerate while I'm already moving.
View 4 Replies
