Sonata NF (2006-10) :: GLS With New Front Brakes And Rotors Still Squealing / Grinding
Jun 23, 2016
I took my 2010 Sonata GLS (86K miles) into the shop last Thursday for an alignment and new front brakes since the old ones were on the wear indicators and doing some squealing/squeaking on soft left turns. Got a call from the mechanic who said the rotors were also shot, so I had them replaced as well.
On my normal commute on Monday and Tuesday this week (approx 10 miles, 95% highway), I noticed that when the car was moving at 15mph or less in a straight line both front wheels were making a noticeable high-pitched squeal/squeak, which went away with increased speed and when braking. I figured it might be a break-in issue but when it hadn't improved by yesterday I made an appointment to have the car checked out by the mechanic again today.
Got the car back today and the same sound is still happening, though now it's in the 60mph range and seems to come and go regardless of wheel direction. The mechanic said he took the brakes apart, found no issues but cleaned and lubed everything as a precaution.
I'm starting to wonder if its the bearings that are shot, but the sound hasn't remained constant as I would expect with a bearing issue. All the parts used are under warranty, so the next step I have available here is to have the brakes and rotors replaced.
View 4 Replies
Advertisement
2011 Ford Fusion Hybrid .. Since purchasing my vehicle in January 2011, I have had continuing problems with squealing brakes and my rotors scoring. They have been replaced along with the linings, pads, etc and less than three months later they are back in the same condition. I drive 140 highway miles roundtrip daily - at least half of that in stop-n-go commute traffic. I never experienced this over the 11 years I owned my 1999 Ford Explorer under the same driving conditions. Have this issue with the hybrid?
View 3 Replies
Mostly highway miles. Squeal doesn't happen all the time, only sometimes.
The pads I bought were from O'Reily's here and I believe they were BrakeBest Ceramic brake pads. Should I give it some more time for the squeal to go away? could it have been a poor brake job? (I didn't do it)
View 20 Replies
After driving my 2007 sonata for around 10 minutes, there is a very high pitched squealing sound that is intermittent and stops when the brakes are tapped. I was told it may be due to a "brake sensor"??
View 20 Replies
Knock on wood 38,000 km and only now had my first set of real problems.
1. Seat heater on front passenger doesn't turn off
2. Brakes squealing
3. Keyless Fob really doesn't work well
I must say after my 05, this 06 is truly a blessing. I can't begin to tell you how utterly amazed I am with this vehicle on a daily basis. Why doesn't the car have any speakers in the rear window deck? Was sitting in the back seat on Valentines Day and was amazed at how weird the car sounds without speakers in the rear? Was truly amazed that my rear passengers couldn't hear how great it sounds in the front.
View 3 Replies
I have a 2007 Sonata V6 I bought used two years ago. When I bought it mechanic serviced the rear brakes as the caliper was sticking. Now the rear brakes make a grinding noise when I brake and when I drive the rear brakes make a sound like slight metal on metal contact. I know Sonatas are known for brake problems. Should I replace the rear pads, rotors, calipers (including pins) and if so what brands are decent to buy? I have used rock auto in the past.
My car has about 198,000km on it (123,000 miles).
View 4 Replies
I performed brake maintenance today with my brother on my 2010 corolla CE, my front rotors were warped and my pads were used ( and also uneven) and I replaced both front rotors and pads.
The install went smoothly, my brother changed a couple of brakes sets and knew what he was doing and showed me up.
Took it for a spin, the brakes work very nicely ( i bought the ceramic wagner bundle ) but theres a slight grinding noise when driving, like the pads are touching and rubbing a bit too much on the rotor, but the driving is unnafected. Also, there's a sqealing noise coming from either side when you turn only.
Braking itself produces no noise whatsoever, only when you turn that it squeals.
View 4 Replies
We discovered that our 99 mercury Mountaineer had bad rotors. last night I hooked up a trailer and was going to work with a friend move a couch when I heard a loud grinding sound. I turned around and determined it was coming from the wheel. I purchased a new set of pads and started to change the pads. In the process I found a broken sway bar connector. I changed this as well. It still felt bad and there was a sound when I braked.
I took it to pep boys for a free brake inspection. They pointed out that the rotors needed to be replaced. I did not let them do it because I can not afford that right now. The car is a secondary not a daily driver. My wife says we shouldn't drive it at all. I say we can still drive it and expect I will have to replace the brake pads sooner than normal and replace the rotors when we can, later. My wife insists we will do more damage if we drive it as it is. I say what's the difference we need to replace the rotors anyway.
View 7 Replies
I noticed yesterday a sound, like a grinding sound, *sometimes* as I apply the brakes to stop. I'm at 68k. The noise only happens when the brakes are applied so I suspect there is an issue with my brakes again.
Some BACKGROUND info: At around 60k (or 8 months ago roughly), the front pads were replaced after the brakes were squealing and a pulsating brake pedal when stopping. The pads were replaced by a dealer. In addition, both front/rear rotors were turned at the same time. Rear pads had 40% at the time and were not replaced.
Some weeks later the pulsation came back and I went back again and they machined them again. For this current issue I was thinking about taking the car to someplace local (not a dealer) and getting a free brake evaluation of what is going on.
I'm also concerned that all this machining the dealer did to eliminate the pulsation may have decreased the life of the rotors and perhaps they need replacement now.
View 3 Replies
I heard a grinding noise from one of my rear wheels. After investigating, I saw that the OUTER pad was worn down all the way. I had only driven 15K and it had not been very long so I did not expect this. I also didn't hear the warning tabs as the they are on the inner pad and it had not worn down enough. I checked the caliper slide bolts and they were gliding freely. I checked under the boots and there was still grease in there.
My old pads had only been worn to 30%-50% so I installed those on for now. When I compressed the piston, I had a hard time getting it started and had to apply a bit of force with the C-clamp, but then it compressed without the need for much force. When I put the pads in, it was pretty hard to get them into the clips. the inner one required me to press pretty hard with my hand, the outer one was so tight, I had to use the c clamp to get it all the way up to the rotor.
I'm wondering what the cause may be. Are there some typical causes for why the outer pad may wear faster? I would think if the caliper bolts were stuck, that would do it, but they move freely? could it just be that the pad is too tight on the slider? How might I fix that? I tried filing them down a little but that obviously wasn't enough.
Also, now the pads on the right and left are uneven and the rotor on the right isnt smooth anymore. Should I go ahead and change out the pads and that rotor? Does uneven pads or a rough rotor affect the effectiveness of the brakes significantly? They are the rear brakes so I would think there is less of an impact. I know that uneven pads and a rough rotor will cause them to wear faster, but if I need to replace them anyways, I might as well wait til they wear down more.
View 17 Replies
I have a grinding noise coming from what I believe are the front brakes. It happens when I apply the brakes and sounds like the brake pad is worn out and there's metal-on-metal contact but when I checked the pads, they are at 80-90% (rears have about the same amount left). I hear it the loudest just before coming to a full stop, from about 20 mph down to stop. I thought it was caused by rust on the brakes but after I wore off the rust, the sound is still there.
View 14 Replies
There is this incessant squealing and grinding coming from my brakes. I have taken my 2010 Hyundai Accent to FOUR different mechanics and none of them have been able to figure out what is wrong with my brakes. I have replaced all of them and each mechanic has cleaned and adjusted them. But THREE days after, every time without fail, it is back as bad as it was before. It is only the rear right brake drum that is doing it still and I have no clue what to do. Something is definitely wrong with this car.
View 3 Replies
Here's my issue, after a full break job my right front brake began to grind. Curiously it wouldn't grind initially after breaking soon after start up. I could go on and slow break for quite a distance, but soon after a hard brake or just slow breaking long enough the grinding begins. I've taken the car back to Firestone three times and even after a few adjustments or cleaning the problem persist... I've starting to feel bad for Firestone and embarrassed to be holding on to this 99 Chevy. I can't continue to drive this small car that sounds like a MTA bus while braking.
But I digress... I did notice, purely by accident (or it may be a mere coincidence), a few times the ABS light came on and during those periods the grinding was less abrasive. This leads me closer to believing the issue is with the caliper.
View 11 Replies
2013 Platinum. See sig for details. 37,000 miles. 1 owner. Truck has been basically parked since June. However I take it out for a quick spin every 3 week for 10 miles or so. Currently has storage insurance on it.
When backing out of the garage the brakes are grinding and squealing bad. Also getting feedback through the steering wheel for the first couple miles which leads me to believe it's one or both the front brakes.
View 6 Replies
When I 1st brought the car the original brakes and rotors squeak, I really didn't mind bcuz I had plans on changing them, now I installed the aftermarket slot/drilled rotors with new ceramic brake pads, and I still get squeaking from the front brakes, weather it's wet or dry, cold or warm they squeak, what I can do to stop this?
View 5 Replies
was going to do a brake job on my f250 light duty and the rotors won't come off. At first I thought they were rusted on but after looking at them it looks like the studs are attached to the rotor. Need to confirm this because the new rotors I got don't have the hub attached. Don't know if it's the wrong part or what?
View 9 Replies
I just replaced rotors and pads on my 2007 Sonata. I got top of the line premium rotors and ceramic pads from Napa. Cleaned the oil off the rotors and gave them a light sanding before installing, made sure that the caliper bolts moved freely and the caliper pistons were not seized and also used new hardware kit (springs?) that came with the pads.
Everything seems to be ok, except for a clicking sound that occurs on hard breaking as the car is coming to a stop. I think its caused by the pads moving within its mounts (I did notice it was very easy to slide these pads into the mountings, more so than in previous pad replacements).
Reading from other posts I think this is still safe, but the clicking does bother me, should I use pad adhesive to stick the pads to the caliper?
View 7 Replies
2006 Sonata V6. Front brakes only squeal when applying them while in reverse. Happens all the time......cold/warm start, cool/hot weather, dry/humid air. Squeal is extremely loud. I have searched and found similar but nothing exactly like this. Pads and rotors are fairly new and I have removed them and reinstalled and regreased twice. I am using ceramic pads and have never used them before. Is this common with them?
View 8 Replies
The ABS and ESC lights (amber) in my 06 Sonata are coming on intermittently.....
The lights just come on while driving....the ESC switch doesnt have any effect.....the brakes seem to work well....then, after several start cycles the lights will go out and all will be well again....then after a few start cycles and while driving they come on again.
I used the code tester from autozone but no codes are stored...they told me that brake codes aren't always accessible with their hand held unit though....
Also, I have noticed that when turning left or right I get a squeaking from the front brakes now and then,...it was doing this before the ABS/ESC light issue though...
View 3 Replies
I bought a brand new 2010 Sonata in April 2010. So far I only have 2500 miles on it. The problems I am having are:
1. When I apply the brakes, there is some vibrating sounds coming...
2. The passenger side front tire does not hold air more than 25-26 psi.. If I raise it to 34 or even 32 psi, it drops down to 26 psi within a week and then stops leaking...
View 9 Replies
Have all kinds of front end knocks and clunks going over bumps and when stepping on the brakes when backing up. Looking to make a parts list to replace everything at once. I see the upper control arm has 2 bushings and a ball joint, the lower control arm has a bunch of bushings and a ball joint. What else should I replace?
View 8 Replies
