Sonata NF (2006-10) :: CEL Code For PO711 For Trans Temp Sensor
Dec 12, 2012
My engine light came on the other day and the code given was P0711, which is the transmission temperature sensor. I went to the dealer and bought one so I can quickly replace it. My question is, where is that sensor located? My haynes book doesn't even mention it. I called the dealer and was put on eternal hold.
View 5 Replies
Advertisement
I have a 2011 Sonata with 30000 miles. It started shifting funny. It would jump when you put it in drive and shift strangely in all gears. Called the dealer to make an appointment, cancelled as I couldn't get off work. In the meantime, car stopped doing this.
After a while, this started again. Stopped by a shop that offered free code check, the code is P0711 Transmission Fluid Temp Sensor. They said your fluid is overheating and we don't know why, we have to take the transmission off to find out the cause.
View 21 Replies
I have an '06 F350 dually with a 6.0 diesel. I bought this used about 5 years ago and for the most part have loved it. i would always smile on the inside when i heard people bash the 6.0...i thought i got lucky....until today.
140k miles. recent oil change. all is swell...until this morning. Stick in key and turn it. glow plug indicator comes on...all lights come on for a few second....wrench, abs, dtc etc....wrench shuts off...glow plug light comes on...4 or 5 seconds later wrench light comes back on....turn key and NO CRANK.
All fuses are fine...starter cranks if i jump the solenoid...but it won't start. Miles to empty and everything else is just dashes hit the OBD and it says "engine sensor data error"/ "trans temp error" ...
View 1 Replies
I went to Jiffy Lube and got an oil change, fuel system cleaning and cabin air filter replacement & sanitizing. I drive an '09 Sonata with 112K miles. When the car came out, I pulled away and noticed that the airbag symbol on my dashboard was lit and the center console was flashing that my passenger did not buckle their seat belt (I didn't have a passenger or anything on the seat). I went back in and after they looked at it, they said they couldn't find anything that could've happened at anytime and was a "horrible coincidence."
Hyundai ran a diagnostic tests and one of the 4 things that came back was B1389 (in addition to B1516, B1324 and B1515). B1389 signifies "Oil Temperature Sensor Circuit Failure." If the guy changing the oil damaged this (does this even get touched on an oil change), could that have offset the sensors for the airbags?
I just don't see how they done the above listed work and coincidentally my airbags are all deactivated afterwards. I'm reading a lot of bad reviews online, including quite a few for NOT putting oil back in the engine after the change.
View 19 Replies
I guess the prius (any prius) has no Trans fluid temp sensor. I tried all 3 general Trans fluid temp codes for Toyota and none work.
2012 Prius c
2016 Prius v
View 6 Replies
My check engine light came on the other day, and I went to Autozone to have the code read. Of course, that indicated the camshaft position sensor was detecting a fault. I read through all the posts relating to the fault, headed up to my local Hyundai dealer, and picked up the oil flow control valve for about $50 plus tax. While I was there, I figured I might as well have them do an oil change, since it was way past due. No point in putting in a new part with dirty oil..right? They did the oil change, washed the car and I was ready to roll. My plan was to replace the part myself, but magically, the check engine light has not come back on since.
View 8 Replies
I have noticed my trans temp gauge needle is dead center of the gauge even on a cold start. I thought my sensor was under the pan so I pulled it and did not see any sensor at all. Is there a external sensor?
View 5 Replies
I have an isspro sensor that I need to install on my 4r100. I have it all installed except for the actual sending unit. My question is where is the best place to put it?
I've watched multiple YouTube videos and it seems a lot of people use the test port on the driver side above the linkage. I found out the hard way that it is a very poor choice of location. A lot of people say that the best way is to drop the pan drill a hole and weld in the bung? I was wondering would it be possible to put it on the "out" line on the transmission oil headed to the cooler? 01 f-350 7.3
View 4 Replies
I was driving today when the CEL came on, I scanned the car which gave me 1 code: P1296.
I googled it and said it is possibly the coolant temp sensor?
The Engine temp was normal at 190' or just below even after quite a bit of driving today.
Would the problem just be the sensor or should I be looking for other problems as well?
The car is a 2002 B5.5 AWM 1.8T Tiptronic.
View 4 Replies
So my check engine light came on in my 04 jetta sw, and when I had the car read, it gave me a code that tracked down to be a bad coolant temp sensor. I bought the replacement part from my local VW dealership, installed it and the check engine light went away. Now about 2 weeks late it came back on, and I am getting a reading of "Coolant temp sensor high voltage". So it goes from needing replaced, then the replacement is running high voltage?
View 3 Replies
Threw a coolant temp sensor code yesterday morning:
16502 - Engine Coolant Temp. Sensor (G62): Signal too high
p0118 - 002 - Lower Limit Exceeded - Intermittent - MIL ON
Does throwing that code once mean I need to replace the CTS immediately or am I safe to clear the code and see if it returns? No code today after a 40 minute drive.
View 3 Replies
What the heck? I have not heard of an over heated O2 sensor. I know they have an extra wire in them for a heater element but I have two temp codes indicating the failure and a permanent code as well.
I know its under warranty but what a weird failure. Overheating...Guess Ill be making that appointment at service earlier than I expected.
View 10 Replies
My first Prius, an 05 has 249K and performs pretty much flawlessly. My second, an 04 which I purchased in May, has 75K. While driving the 04 yesterday, all the lights came on the dash and really scared me. I immediately pulled off the road and checked belt, fluids and anything else I could. I then called the dealer and they thought since the car was running normal, to bring it in. For a hundred dollars I was told the HV battery, though working and not a problem, would have to be replaced due to a faulty "battery temp sensor" and that this part is not repairable....I need a new battery! Code POA9B ... Tomorrow I am taking the rear panel out and check the HV battery fan, etc. Can I drive the car with these lights on? Everything seems to work but the CC.
View 9 Replies
P3081. What the hell is this code. I think it is a coolant temp. sensor issue.
View 3 Replies
My 2003 Mk 4 Golf have had a lot of error codes and I have cleared most (O2 sensors, thermostat, and Mass Air Sensor) I now have an error P0113 which is the Intake Air temp Sensor.
So I need to clean the sensor first then maybe replace it, but I can't find the sensor on the intake manifold.
I have looked all through the U-Tube info, but nothing matches my 2003 Golf 2.0L ...
View 2 Replies
2001 jetta 2.0 VW guys a while back I was pulling a code saying that the air temp sensor circuit was low I believe it was P0112 so I replaced the maf with a bwd maf. Said it was for the car. Was fine for a day but now it has a P0102 code and the epc stays on (rough idle) what could be wrong ? Is it because the car hasn't learned the new sensor yet because I've only drove 10km or do I have a faulty sensor. BTW replacing the maf fixed the P0112 code
View 5 Replies
My 2003 Mk 4 Golf have had a lot of error codes and I have cleared most (O2 sensors, thermostat, and Mass Air Sensor) I now have an error P0113 which is the Intake Air temp Sensor.
So I need to clean the sensor first then maybe replace it, but I can't find the sensor on the intake manifold.
I have looked all through the U-Tube info, but nothing matches my 2003 Golf 2.0L ....
View 3 Replies
I recently got the solid check engine light for my 2003 VW Jetta 1.8T GLS. I used a bluetooth OBDII dongle and Torque Pro to pull the code P0118. This seems to coincide with my symptoms:
Car idle at start in park stays around 1100RPM then in reverse it drops to 1000RPM then back into park and it stays around 900RPM and keeps that at idle.
If I start the car then immediately reverse out of my driveway then the car has a very rough idle but if I wait around 5 seconds in park idle then reverse out of my driveway it is smooth.
My car dash thermometer stays pretty close to the bottom low then after about 4-5 minutes it shoots up to 190F and stays. Gas mileage is also very poor.
I looked up a tutorial which shows the parts needed and how to replace the sensor : [URL] .....
I removed the engine cover and believe I found the coolant temp sensor in the spot the tutorial shows. My question is if there is anything I should be aware of before attempting to replace this sensor that this tutorial doesn't cover? I took a screenshot of what I believe is the coolant temp sensor.
View 8 Replies
2001 3.0 XLT Ranger 2wd 4 door
Okay getting ready to trade in my Truck. So I removed all the extra things I put on there while I was in college, the amp, fog-lights, and analog oil pressure sensor along with their wiring. It was pretty easy minus removing the oil pressure sending unit part.
I had to unplug the MAF to move the intake out of the way while I was repairing a loose vacuum tank. But I forgot to plug it back in when i closed everything up. I started the truck and drive it about a half mile before I was able to pull over and plug it back in. Truck ran and shifted fine after that, but the CEL came on. P0119 Coolant Temp Signal Intermittent. Guy at Autozone said it was Intake Air Temp Sensor intermittent and I could just replace the part, but they were showing a separate part even though it is built into our MAFs.
So now the CEL is on, can get it to go away. Truck is a little jerky every once in a while, like a misfire, when between 50 and 60. Before all this the CEL was off. Now after I cleaned it up and removed some of the superfluous accessories, I get a CEL. I wanted to trade it in this coming weekend without having to take a loss because of the CEL or spend more money to fix it.
View 3 Replies
I have a a 02 jetta 1.8 turbo the code po343 came up after new temp sensor,valve cover gasket and full tune up. is it an easy fix the car is misfiring an very hard starting.
View 1 Replies
I had CEL the other week scanned and found P2043 Reductant Temp/Sensor range. Light came on first thing after a cold start.
View 13 Replies