My dad drives an '06 Sonata. And he recently broke a brake line and had gotten it fixed. His current problem is that his brake pedal hasn't returned after getting the line fixed. What can he do to fix that? The pedal is really low and is spongy. And his ABS and ESC lights are also on.
View 4 RepliesI have a question about the bleeding the brake? When I washed my E, I usually spray the wheel and the brake part. I don't know it is a good idea or not. Recently, I felt like I have to step further on the brake pedal to apply the brake.
The force is there and Brake assist is still in effect if I step fast enough. I just felt like the brake pedal is spongy. My E is on 36k right now. Do you think wash the wheel often will cause the problem to brake line?
I have confirmed that my Gf's Elantra is easy and ease to brake than mine. At the mean time, her brake fluid is darker than mine. My brake fluid is full and clear. Maybe I should not wash the wheel more often. Or maybe I get OCD too much?
I have a 2000 Silverado 1500 replaced calipers, master cylinder, and ABS Pump/Modulator. Bled all four calipers. Brake pedal spongy and has very little pressure and travels all the way to the floor. What am I missing here?
View 8 RepliesI just finished replacing pads, calipers, rotors, wheel cylinders & brake drum hardware on my truck along with flushing the brake fluid. The brakes work but the pedal goes almost to the floor. While bleeding them some air did come out as expected. But a couple times the master cylinder reservoir got very low on fluid. The workshop manual talks about bleeding the MC but are special fittings needed for that?
View 10 RepliesDrove the lady's car out on some errands today and ran into a problem on our drive home. Car was pinging really bad (low rpms in 1st and second) and car seemed as if it couldn't get out of its own way. Was driving for some time on the freeway (after a blistering 0-60 time of 20 seconds ), and noticed that the brake pedal was really spongy (felt like a mk1 when you try to brake with the car off). Found that the e-brake handle was up (negligibly up (perhaps 1mm raised)). Didn't have power brakes at all and had to use a lot of engine braking to slow the car off of the freeway.
Rear of the car smells like copper (wet pennies) and found that the brake reservoir is cracked (but fluid still at max level). Also noticed that as of late, when the car is at a stop (sometimes in gear, and sometimes in neutral) the car will rock/bump a little almost as if someone were giving it a bumper kiss with their car.
My Gen I Prius is screeching at me with the BRAKE and ABS lights on, and I hear the electrically actuated pump pulsing as it tries to get pressure into the system. The pedal is spongy and will go all the way down, with the right amount of exerted pressure from my foot.
View 6 RepliesAfter my local brake shop changed the front rotors and brake pads on my 99 grand cherokee the brake pedal is spongy and long, almost reaching the floor. They don't know why. Apparently they had a problem with fitting the new pads. I took it to the jeep dealer and they told me the master brake cylinder was leaking and needed to be replaced. many hundreds of dollars later the brakes are still spongy and long and does not correct with repeated pumping. The dealer was also stumped and I complained that nothing changed with the new master cylinder. what might be the problem?
View 4 RepliesI have a 2008 Ranger Sport 4x4. I noticed yesterday that when I stepped on the brake pedal it felt like nothing was there until I step a little harder then it was like full brake application. The truck only has 63000 on it. Then every once in awhile it would be normal ie very light brake application and slows like it should. Then back to same issue... Any thoughts about this??
View 8 Replies2009 XRS ABS brakes .... I changed all four brake pads and flushed out most of the old brake fluid. Bled all four sides. But now while I am in idle (like waiting for a light to turn) my brake pedal is spongy and is making a hissing sound. All was good before I did this job.
View 3 RepliesI replaced all the brake pads on all 4 wheels. Pretty standard procedure. I now have a very spongy brake pedal. It stops but the pedal will be almost to the floor. I did not break any of the lines open during the procedure just used c-clamp to spread the calipers. No ABS light. Have a Snap-On power bleeder and bled the system several times with no change. Checked the power steering fluid level and inspected entire system for leaks.
2002 F-550 V10
I noticed last week that my brake pedal seemed more spongy than usual. The next day the pedal would go down about half way to the floor before I had pressure. And then the next day the pedal would go straight to the floor. Pedal comes back up once released. I still have brakes pressure about an inch before the pedal bottoms out. Its been like this a couple days now. The vaccum pump works fine. I'm gunna try bleeding the brakes on it tomorrow.
View 5 RepliesI have replaced booster, master cylinder, all four callipers, and bled the brake system a number of times on my 2000 F-150 4x4. and still the pedal is wicked spongy, is there some other problem?
View 6 RepliesWhen I press the brake pedal, the car will stop. But if I keep pressing it while the car is stopped, the pedal wants to keep going towards the floor. I have to press hard for it to do this. I have bled the brakes. I've checked the calipers and the hoses for leaks and don't see anything. The master cylinder is topped up and I don't see any fluid underneath it. It doesn't appear to be leaking. The funny thing is, when I turn the engine off and press the pedal, the pedal comes to a stop and doesn't want to move after I pressed on it as hard as I can.
View 2 RepliesI have a 2007 Sonata GLS 4cyl. Anyhow lately my brake pedal is going right to the floor. The brakes seem to work fine, but if I keep constant pressure on the pedal it will slowly go all the way to the floor. My rear rotors and pads have been changed a couple of months ago and I'm pretty sure my front brakes are good. What could be causing this? I also checked underneath the car for leaks and there doesn't seem to be anything leaking underneath.
View 6 RepliesI drive almost all the time in stop and go traffic and my knee hurts because the brake pedal is too high. My wife also noticed that the brake pedal is unusually high. Is there any adjustment I can make to lower the brake pedal?
View 2 RepliesThis afternoon while I was driving home from work I heard a minor squeak so I put the windows up and the radio off. t I heard my brake pedals chirp. It's a small minor squeak, but I hear it and it's bothering me. Am I over thinking this?
View 20 RepliesMy Sonata 2008 2.4 produces a single click as I press brake pedal, somewhere half way through. You can hear it and feel it with your foot. I think it clicks somewhere inside the hydraulic system of the brake.
View 13 RepliesSo I took the pads off and saw pistons that push caliper against rotor were to far out to install new pads. (rear pads were still intact, both front pads were out when i pumped) So im pumped the brakes thinking it would reset them and alls it did was push the fronts out more.. I noticed fluid leaked out of the pistons after fully pushing them out.
After seeing that pushing the pedal only pushed them out and didn't reset them, i pryed them in with a C wrench. Was quite difficult but managed to do it. Note I only did this on the front pads..
Rear was just fine, piston went back in easily. I filled brake fluid fully and still does it - Now pedal hits the floor when i first hit it and seems very light when braking.
I have only 42k km or 26 k miles. Brake stops but soft. The brake pedal sink if you apply pressure after a stop. Feels like someone open a valve. The pedal go to very low. I am find the stopping power is poor. Brake fluid is brownish. I hope it is not the master cylinder.
View 20 RepliesI just noticed it this morning. When I step on my brake pedal, all 3 brake lights activate, then they start to sporadically blink, I don't think it's a fuse problem, since the 3rd brake light also blinks, and I believe it runs independent of the regular brake lights.
What to check.. No codes are being listed, checked that with my Scangauge II already. (2006 GLS)
Ive got a 2002 f250 Sd 4x4 with 93000. Im getting severe vibration from the front drivers side at highway speed. I thought it might be a warped rotor but i cant feel it in the brake pedal, when I put the brakes on. How can you tell when the hub bearing assembly is going bad? The truck doesnt pull to that side either. I can hear it, and feel it more when i'm going around highway corners. When im driving through town, I can hear a "clunk,clunk,clunk" noise coming from that side also.
View 14 Replies