Sonata NF (2006-10) :: 2009 - Evap Purge Valve Location
Nov 2, 2014
Where are the canister and solenoid valve located, above the tank? 2009 Sonata 2.4L ....
View 1 RepliesWhere are the canister and solenoid valve located, above the tank? 2009 Sonata 2.4L ....
View 1 RepliesHave a 2012 gas powered Escape XLT, 2.5L 4 cylinder.
I need to replace the evap purge valve. Looking at youtube videos and from other posts it seems easy to replace. My problem is where is it located on this Escape?
Is it under the hood or underneath the driver's side? This is just the valve mind you, not the canister in the back.
I have difficulty starting after I fill the tank (usually to about 3/4 fill, not topping off.)
I searched the forums and noticed the evap. system N-80 purge valve may be the culprit. Other VW's have the issue including one thread on a Touareg.
I think I'm the first with this issue on a Phaeton. Sometimes getting loose gas cap faults too and on occasion a CEL. I had a fuel pump replaced last week, but this problem predates the pump failure.
Does this sound like the issue here? Doesn't it throw a code? I'm wondering why they didn't discover it when the diag'ed the bad fuel pump.
I have a 2001 saturn l200 2.2... Well I put the new EVAP Purge Valve in last night.. Today I start the car and started to clicking so I unplug the new EVAP Purge Valve and it stop clicking and i plug it back in and started clicking..
View 6 RepliesI only have 2200 miles on my new 2012 Passat SE V6 and the check engine light came on the other morning. I took it in to the dealer and they found codes P0442 (EVAP Emission Control System Small Leak Detected) and P0456 (EVAP Emission Control System Very Small Leak Detected). The tech says on the work order that he removed and tested the EVAP Purge Valve with a vacuum pump and the valve would not hold a vacuum. The dealer replaced the EVAP Purge Valve under warranty. They say this is the first 2012 passat V6 they've seen with this issue. I've only had the car for 4 weeks.
View 5 RepliesWhere the EVAP canister purge solenoid is located on a 1999 Ford Windstar with the 3.8 engine?? I replaced the vent valve that is located on the canister itself but cannot locate the purge solenoid valve.
View 2 RepliesReplacing part 9C915 ?
"CODE P0443 canister purge fault" diagnosed....
Found: EVAP PURGE FLOW VALVE STICKING
Recommending: "Diag, Replace sensor then retest" ....
They want to install a new 9C915 which they called in hand writing a Canister purge sensor but I've seen it called a canister purge valve on another thread by FIREME who puts 9C915 as "toward the driver's headlight assembly, near the radiator. You'll need an 8mm socket to remove it"...
3.0L DURATEC FFV V6 ENGINE
From the "newly washed ashore" who's now double posting after being flogged for trying to keep this info in a single thread rather than spreading it all over the place...
Engine light came on a week ago, finally made it in to get the code pulled yesterday : P0441
From reading on this site, thinking its a faulty purge valve.
I have found pics of its location on an 04, but cant seem to find it on my 08 2.7L.
Changed my oil today and check the air filter. I noticed that there is oil on the air filter, so I'm thinking the PCV valve is bad (car has 136,000 miles). I want to check it but I'm not sure where it's located. Where it's located (pictures would be great) and how involved it is to replace?
View 4 RepliesWhere the CCV and its VSV are located on my 2000 toyota Celica? Is the CCV also called the Evap vent valve?
View 3 RepliesMy 06 accent GLS has become difficult to start only after refueling, which I'm guessing is related to a bad purge control valve from what I've read. Where exactly is the valve located, and is this something that someone with relatively little automotive repair experience could do on their own? I think I've located it on the backside of the engine near the air intake.
View 2 RepliesI recently got a check engine light. I went and got it checked, the person said its the canister purge valve that needs to be replaced. Where it is located and the difficulty replacing it. The part is cheap and I want to replace it this weekend. 2007 elantra
View 2 Replies2006 Honda Element 2.4 ... I developed an unknown bad oil leak. Low oil indicator light did not come on. Highway drove it down to one qt. Now blowing blue smoke and lost power. Why my oil light did not come on?
Also, I have needed a purge control valve for quite some time. Could this of caused the oil leak?
Replacing the knock sensor on a 2009-2010 Sonata with a 2.4l? Where exactly is it located and what has to be removed?
View 2 RepliesI've removed the splash guard(s) and can see a bunch of different thick hoses. I have no clue what I'm supposed to be looking for in order to drain the coolant. What I'm looking for (picture would be great or a really good description).
View 23 RepliesJust received a P0441 CEL (Evap Emission System Incorrect Purge Flow). I have a 2.7l engine, 2WD. I've read other forums and it seems it's most likely the purge valve or charcoal canister.
View 7 RepliesI've had the check engine light come on and was told it was probably from topping up too much and that it would go off on it's own... I should say I have no issues with idle or rough starts.
I had it scanned at Auto Zone. The print out shows: "EVAP emission system incorrect purge flow probable cause
1) Faulty purge control solenoid
2) Faulty vent solenoid
3) Blocked vapor canister
Previous posts suggest if it were a blocked vapor canister I'd have trouble completely filling the tank so I am hoping it's one of the others. Almost everything I see suggests the purge control and that looks like an easy fix. My concerns are a) if it is the vent solenoid - how hard is that to get at and b) what is the part number as I can't find it listed anywhere? I want to have both on hand before I start trying to fix this. Lastly if it is the vent solenoid should I just give up and see a dealer??
I need to test the fuel pressure on my 2009 Tiguan. I need to know where to locate the Schroeder valve.
View 1 RepliesNot too terribly long ago I got assistance on identifying and fixing an engine misfire on my 2009 Accent. I assumed was directly connected has cropped up again - a P0497 Low Purge Flow error has come up on the car.
We recently replaced the purge flow valve, and everything seems to be running fine - there is no visible cause for the error, and I've even tried making sure I get the fuel cap as tight as possible.
The code is not popping up constantly - this is only the second time it's come up since the misfire was fixed(without obvious symptoms I always clear a code once just to make sure it wasn't a computer glitch), and the first time it popped up on it's own was the day after I fixed the misfire. Need to know what to check to find out what's wrong and, of course, how much priority I should place on fixing this issue.
The purge valve keep clicking means it is fail?
View 2 RepliesLooking for the location of purge valve on a 2003 aviator ?
View 8 Replies