Silverado :: Truck Is Running Rough / Loss Of Engine Power?
Sep 21, 2014
why my truck is running rough the problem I am having is when you push the gas peddle more than a 1/4 of an inch it shudders and has no get up and go and also if say I'm doing 40 MPH and hit the gas you can hear the engine rev up but I will lose all power and actually lose speed I thought maybe the cats were bad and I changed the plugs for good measure but I can't seem to figure it out also I had the fuel pressure checked and its pulling pressure is great/
View 6 Replies
Advertisement
'01 Silverado with the 4.8, sitting at 160k right now. I'm starting to notice a loss of power in the truck, when pulling out and accelerating it doesn't put you back in the seat like it used to and when going up a hill you have to force a downshift to not lose 15-20mph... it just seems like I'm pulling an invisible trailer back there. The fuel pump is about 1 year old, fuel filter less than 3 months, plugs and wires are about a year and a half old, PCV valve about 6 months old, fuel pressure regulator about a year old..
View 3 Replies
Well it finally happened, a couple of weeks ago I was headed to an MX race and my check engine light came on and it started running rough. Long story short a piece of an exhaust valve broke off and went out through the head. Dealer has been great even though I was 300 miles from home and they did get me a rental(small POS SUV). Truck was supposed to be finished this week, but now they are saying the head gasket is on back order and they probably won't have one until the middle of April......... I can't be without my truck that long, but not much I can do. By the way truck is completely stock with just under 20K on it, and I have never had any issues with any of my Ford trucks or Ford diesels, even my old 6.0.
View 7 Replies
I have an 88 chevy K-1500 4x4 5.7L ... My truck lacks serious power, it idles rough, sometimes wont idle at all, sometimes Truck Idles fine. I have adjusted the timing to tdc, and 4 deg. both ways still runs like crap.. Sometimes I can keep it idleing, put it in rev. or drive, and it will die. I have no power and if I put my foot in it too much it will backfire. but will only backfires when in gear and press on the gas to put a load on the motor. I have replaced the: tps, map, egr, pcv, distributor, cap, ignition coil, rotor, plugs, wires, timing chain, both sprockets cam and crank, checked all hoses for leaks, replaced the injectors, the O2 sensor and have changed the intake gaskets. And am still having no luck...... I am bout to just drop an M80 in the gas tank and watch her burn..
View 14 Replies
My wife was driving the 1999 K3500 7.4 model ls crewcab truck home the other day and out of the blue it started running rough popping and back firing and lost power. It had a major tune up about 40,000 miles ago. It sometimes has a hard time cranking to start, but once it starts it idles really rough and pops and smells like it is running rich. I thought the distributor cap but it looks fine, could it be a sensor?
View 2 Replies
I have a 2001 ford 7.3l powerstroke diesel. When I first noticed the problem I was towing a trailer going up a grade and got into the throttle almost to the floor and noticed a loss of power and the service engine soon light flashing extremely rapidly a few times and never came back on. I made it home, still lacking power but not running rough. I drove the truck to work the next day and the truck was running rougher and loosing power. It ran great through lower RPM's but seemed to trip as soon as you gave it over half throttle. eventually the truck wouldn't run right at all and lacked complete power. It idled rough as well. My mechanic threw the computer on it and it said injector pressure reading too high or too low.
I was told to replace the IPR on the HPOP and I did. (I also replaced the fuel filter and changed the oil). After replacing the IPR it ran great, had full power! then it began to slowly die like it did before until it sounded like it was running off 4 cylinders again. I pulled the ipr out, cleaned it and changed the oil again. It seemed to clear it up for an hour and ran great but then began ran rough again. I also replaced the CPS sensor. I feel like its not getting enough fuel or something, im just wondering if it could be the ICP or the lift pump. There is no check engine light at all. Its just got me stumped because cleaning the IPR clears everything up.... temporarily.
View 14 Replies
My wife's 2000 grand am 2.4L engine is acting really funny. this is the first problem we've had with it. i was driving it to pick up my kids from school. on the way i stopped and got some gas from the marathon then drove about 5minutes and it started running really ruff lose of power wouldn't go above 30mph seemed like the transmission took longer to shifter to.
i made it to the school as i was about 2 1/2 blocks away. got my kids check the oil and it was really low so i got 2 quarts as it was a gas station in walking distance. i thought it was a lil better but i started driving it and it had the same results. i got it home about a 10minute trip regularly and parked it.
the next day day it ran then stumbled hard. and every time i tried to start it got the same think was like a lock up. it did crank but when it tried to start it stumbled or locked up. i pulled the plugs had some wet threads oil was on the first on and the threads and around the spark plug b4 i pulled it out.
2 of the other plugs had red stuff on them not on the threads though. here are some pictures also i will show a vid of what its doing. i did a compression test and here are the numbers starting with the first one with oil on threads.
190-194-200-190+ compression test with cold engine.
Also smoked puffed up not sure from where yet..
View 19 Replies
Driving while in 4x4 HI up a hill the truck started to slip. I stopped, shifted to neutral, and engaged 4x4 Low. I shifted back to drive and started moving up the hill. The engine started to lose power and the "Service Engine Soon" light began to blink. I put the truck in park. As I let it run a little bit, the engine started to shake as if something was very imbalanced. I went to check under the hood, and confirmed that it was shaking quite noticeably. There was no grinding or clattering of any kind though.
I turned the truck off for a bit, and then restarted. There was no light or shaking upon starting up; but as soon as I put it in gear and started driving I could tell it was losing power, the light came back on, and the shaking ensued. This occurred in 2wd, and both 4wd lo and hi. I parked it at a neighbors place and there it sits for now.
I plan to try and get the codes read. My other vehicles can't make it through the snow we have right now, but it is suppose to get warm later today and might melt enough for me to get one out. I also live out in the country, so the nearest auto parts place is about 20 miles. Same with a dealership service shop. I'm hoping I can buy and return a code reader from an auto parts store to assess if this is something I can diagnose myself or not.
It is the 6.0l gas engine with the 4sp automatic transmission. The truck also has about 107,000 miles.
View 16 Replies
About three nights ago I had a complete power loss on the highway and the car began to bog down alot under throttle (and surge at points as well although with no boost). It also idled very rough/erratically. When I unplugged the MAF it cleared up right away; Idle was smooth and it ran without hiccup but in safe/limp mode so very tame (again, without boost really, gauge shows it stays in Vacuum and never passes "0" or goes into boost).
I scanned it this evening and got 2 misfire codes and a MAF code, along with a code related to traction control which I noticed had activated as a result of this and could not be turned on (by activated, I mean the light came on, disengaging T/C). These things make me think it is MAF related, especially because I have bolt down Hitachi coil packs so I do not think that is what it could be in relation to the misfire codes (which I think may be old and needed to be cleared).
Fast forward to last night: I can pretty confidently say my MAF is not the problem and I think I saved an unnecessary expenditure. I was able to meet a friend with a 337 as well and his MAF did not change my car at all and my MAF ran fine in his car so I think my problems are something else. Although with the MAF plugged in my car runs very poor and unplugged it clears up and just runs "limp" (no boost and slow but stable) from what I tested this evening the MAF unit seems to not be the issue.
I think there must be a vacuum leak of some sort between the MAF and the engine which allows more air in than the MAF signals when plugged in which causes the issue. Also, I know a common thing to think is "coilpacks" but I have bolt down Hitachi coil packs so I would imagine that would eliminate those from being the failure they tend to normally be. Agreed ??
View 14 Replies
My Nissan Maxima GLE 2000 is showing CEL with code of P1320 ONLY, and the car is running rough/or loss of power. The shop that checked for the code advised that it could be something related to Ignition, and also provided me with the system generated list of reasons for the code. Before I decide to do anything, I wanted to check what option I have to address this in a most cost effective manner:
1) Is there a quick way to check which coil would have gone bad ?
2) Is it advisable to change 1 LH and 1RH at a time, and see if it fixes the problem ?
3) Could it be cam shaft sensor that could have gone bad ? Are there any symptoms of cam shaft sensor failure to isolate it to one way or the other ?
View 1 Replies
I have a 2001 F350, 7.3. My service engine light came on and immediately the truck started to run rough and lose some power. I've checked the under the cover connections and they were both connected, I replaced the cam position sensor and I still have the same problem. The worse part of the hold thing is that there are no codes stored so I'm flying bind. Where to go next.
View 8 Replies
Drove the truck one week ago today and it ran perfectly fine. Drove it last night for about 20 minutes - ran fine. Drove it again today just 1 minute up the road - ran fine. Started it again this evening and drove it 5 minutes down the road - ran fine. Stopped and put gas in it - now it's not fine. After putting gas in it it refused to start but will turn over. Put a booster pack on it and it will start but would only stay running with the gas pedal pushed all the way to the floor, as soon as you took it off it dies. Now it will not stay running even with the gas pushed all the way down.
View 5 Replies
My Excursion got 4 new injectors a couple weeks ago and when I got it back, it was running rough. My mechanic told me it was going to take about 100 miles for them to break in.
300 miles later and it is still running rough. So I opened the hood, took a look around and saw this wiring harness unplugged. Where it goes? Youtube video shows where the harness is [URL] ......
Also, my truck has been shaking violently at 50 miles per hour, unless I hit tow haul, then it is moved up to 60... I am assuming its connected some how to that wiring harness being disconnected.
View 14 Replies
My truck was running rough when cold, I went to check the ficm voltage while wife was cranking and coolant shot right into the ficm and cooked the sumbitch. Stop laughing that stuff happens to me all the time. Anyhow, got a new ficm and truck wont start. Starter kicks out after a few revs. I ran my own solenoid wire to the starter and it cranks just fine. ficm at 48.5 koeo and cranking, icp 1100+, ipr from 14.8 to around 40%, ...
It takes a few seconds for the cam/crank to sync but it does. I changed the fuel filters and primed it, Got new batteries, and threw a crank sensor for s+g. With the key on and me cranking it using the solenoid wire, it almost starts. But from the key it will kick out after a few seconds. All fuses and relays are good. I hear the pcm also controls the starter, could that have cooked when the ficm went or would it blow a fuse? Diagnosing using a scangauge2 ....
View 14 Replies
I had an HPOP line burst and soak the engine compartment with oil. I replaced the line and degreased the engine and rinsed it off. I started the truck and let it idle for 15 minutes or so before driving it. On the way home right after a shift it started chugging and running terribly. The check engine light was on as well. I limped it the mile or so home and shut it off. I restarted it and it runs just fine. I checked the DTC's with Forscan and there were a bunch of things that were mostly related to the HPOP and the MAT sensor that was shredded when the line blew. I left the hood open to dry out today and I'm hoping it is just some water in a connector. Does that sound plausible?
View 6 Replies
I have an 04 F2 50 with 6.0 with approximately 225,000 miles. I filled up with gas last Wednesday and every so often the truck will start running really rough and then it will clear up. Is it possible to of gotten some bad gas if so what products are out there to clear that up. Could've been injector going bad what are the best products for cleaning injectors. No check engine light on, gauges are good, nothing different on the scan gauge.
View 3 Replies
This has me puzzled to no end. After my son had put fuel in my truck it began to run rough, and had to be towed home, and now won't start. Now the first thing I thought was that he put regular gas in. But he was sure he had not ,and the receipt from the pump indicates diesel. It was hard starting before this happened.
1st Misfortune of having gas put in instead of diesel and did your vehicle run afterwards.
2nd Here are my readings from my scangage:
Sync Yes/1, Ficm main power 48.5 v, ICV .17 (2.01 when cranking). ICP 1572. IPR 50.7.
Checked upper fuel filter for bubbles, none.
Engine oil pressure comes up immediately on cranking.
Don't know what else to check, these readings look fine to me. Only the fuel is something I'm not 100% sure of. It does smell like diesel not gasoline.
View 14 Replies
So I have been fighting a rough running, missing problem. My truck started running rough one day on the way home. I got it scanned, it showed injector contribution balance 1&2. Made sense to me that it threw those codes. I replaced 1 and 2 with oem replacements. Got that all done, truck still ran like crap. I changed fuel filter with motorcraft ones and drained the water separator. That didn't work. I am getting it scanned again, so i will have codes shortly.
Also, for a while it would run with absolute no problem. It was intermittent like that. Run bad run bad run bad and then one day run flawlessly. I though it was electrical. Checked all the common places for chaffing, saw nothing. Even did the wiggle test while it was running, no change. But it hasn't been intermittent for a while now.
View 14 Replies
Since our weather has returned to the cold side......my truck has started bucking and hesitating at 45 mph with EOT @ 130 and ECT @ 140. I can gas on it and it will clear up/let off and it would start up again once it gets below 50 mph. Once the deltas reach 150+ it clears up completely. Its never done this until this week. FICM volts are steady @ 48V. What is causing this or what to look for?
View 2 Replies
2004 F550 with a 6.0. I had to clean out my fuel tank, replace the HFCM and filter on top of the engine. When I start the truck it will run for 30 seconds or so, start running rough then die. I opened the cap on the fuel filter housing on top of the engine to make sure the fuel was getting there. I turned the key on and the fuel bowl quickly filled up.
After a short time however, the fuel drained out. To where I do not know. I don't think this is normal as every time I've changed the upper filter on a 6.0 it is always full of fuel. Why could this one be draining out and could that be the issue why the truck dies after starting and running for a short period of time. I changed the o-ring on the cap and the new HFCM was purchased from Ford.
View 13 Replies
I have a ford fiesta that first of all started off stuttering/loss of power and now wont stay running when the engine is cold ...... 1.4 54 plate ....
View 4 Replies
