Silverado :: 2003 With Code P0307 Misfire / CEL Flashing
May 1, 2014
I'm having an issue with my 2003 Silverado, current engine is LS1 from a WS6 Trans Am, mostly stock, stainless headers, no cats, stall converter. I replaced fuel pump a few weeks ago and last week i took a road trip and when I hit the interstate the CEL started flashing. I pulled over and used my scanner and saw that it was P0307. I cleared code and continued on. The only noticeable problem was that it was not shifting into overdrive. After a while the light quit flashing and eventually it shifted into OD.
This happened several more times on a 750 mile trip. I had a mechanic friend check it over and he couldn't find anything, wasn't throwing codes at that time. He check sparked plug, swapped the coil to #5 and still had the issue. Didn't get a chance to check the fuel injector. The trip home it did the same thing. IF it were indeed a bad injector, wouldn't the problem be ongoing instead of coming and going? Took to local chevy dealer thinking they could diagnose it but since it didn't throw a code they couldn't find anything.
View 5 Replies
Advertisement
I have a 2001 King Ranch F150, which has a 2004 Lincoln Navigator 5.4 DOHC Intech engine installed. The engine was installed in 2005 and had less that 100 miles on it. The engine now has approximately 95000 miles and I have recently gotten a P0307 fault-miss fire on # 7 cylinder. I have installed a new spark plug, COP, and fuel injector. The fault has returned. What is the cause of my problem?
View 1 Replies
I had a 05 f350 5.4 3v come into my shop with a CEL. Did the usual it had a p0307. So I did the usual again changed plug and coil plug cam out no prob they were done 15k ago. Test drove a few times and it was fine. Few days later customer brought back with same code p0307. thought maybe I got a bad plug or coil so I moved them to #6, misfire stays on #7. When I drive it local its fine when I go to pull on to highway and really put my foot in it CEL flashes (misfire) and it pings like crazy and loses all power. Scan it back at shop and still only p0307!!
View 10 Replies
My 2003 Silverado 5.3 has an intermittent CEL. I plugged in the reader and found code P0304, misfire #4 cylinder. I changed the coil, swapped the spark plug and wire from #2 cylinder to see if the code would follow. Nope, didn't follow. I swapped the injector also, same results. My daughter decided to borrow the truck and drove it so low on fuel that the low fuel light came on in the drive way. I added about 4 gallons of fuel and now the light went off. I started the engine after a jump start, and the engine really runs rough and now won't stay running. I am thinking that the fuel filter is probably needing changed because of how low the fuel.
I haven't checked the fuel pressure yet and will do that today. Now, what really puzzles me is the intermittent part. Sometimes it will run with no problem, but then the CEL will come on and the fun begins. The Chevrolet dealer says it's caused by the valves turning in the head and when it reaches a certain spot, it detects the misfiring #4 cylinder resulting in the CEL. If I pull in the driveway with the engine missing, go back out in a short time, start the engine and it runs fine. Same thing if it's running fine and I can start it and the CEL blinks and it begins missing, but may stop and run fine. I am stumped and not so sure about the turning valves.
View 9 Replies
I have a 2001 King Ranch F150, which has a 2004 Lincoln Navigator 5.4 DOHC Intech engine installed. The engine was installed in 2005 and had less that 100 miles on it. The engine now has approximately 95000 miles and I have recently got the P0307 fault-miss fire on # 7 cylinder. I have installed a new spark plug, COP, and fuel injector. The fault has returned. Any clues to the cause of my problem?
View 5 Replies
I have a 2001 chevy silverado 3500 6L gasoline engine.
I have been getting a P0307 random multiple misfire #7 on and off for a few months now, occasionally the P0300. Check engine light comes on when I am going up hills, often under heavy load and sometimes when the truck is cold in the morning and the truck starts to run rough until the code clears, which it does pretty quickly usually. I have replaced coil, crank sensor, cam sensor, fuel injectors. If I unplug the battery overnight the code will be cleared and the truck will be running just fine the next day.
View 6 Replies
99 F250LD 4x4 w/5.4 and 215k . I'm sure I'm not the only one with this problem. Just had quite a bit of rain in my area. I didn't drive the truck in it but 3 days after the rain stopped I did. Skipping badly ! It has done it before and will clear itself up after a heat cycle or two. This time it kicked a p0307 code. # 7 cylinder not fire correctly I believe. I got ready to replace the cop but decided to wait a day. In the mean time I pulled the connector and blue compressed air through it and the male connector.
The next morning I decided to drive it before replacing the coil. Absolutely no skipping at all. Drove at different speeds , up heels slow , high speeds, no skipping. Ran the truck for about 20 minutes or so. Is the connector getting moisture in it ? Can I fill the connector with dielectric grease? Is there another problem. I cleared the codes and am going to drive a couple of cycles to see if any come back. Like I said it has done this before but not bad enough to throw a code so I'm not sure if it's always number 7.
View 5 Replies
So I have A 2000 Chevy and i keep getting a code saying i have a misfire on cylinder 8. i have replaced the spark plug, i have replaced the coil. this code is still showing up. what else could this be?
View 2 Replies
I'm getting consistent P0305 and P0307 misfire codes when my 4.2L engine is revved past 5,000 RPM. Have a done a bunch of diagnostics including a new timing belt to no avail.
Specifics:
I have 2001 Audi A6 with a 4.2L 40V engine (yes, I know it isn't a Touareg but the motor is the same!). Timing belt replaced about 1.5 years ago and it runs great. However, I'm getting some codes. 1) At high RPM (over 5,000 rpm) under load, I consistently get a P0300, P0305 and a P0307. Happens like clockwork. As soon as I hit 5,000 rpm, those three codes post. 2) After driving around for a bit, I get a P0340 (Cam position Sensor). Things I have done, all with no change: 1) Checked for Vacuum Leaks 2) Replaced all the spark plugs 3) Moved all the coil packs from one side to the other 4) Replaced the Cam position Sensors 5) Moved all the injectors from one side to the other 6) Inspected (as best I could) the variable cam timing system under the valve covers. Brown chain guides looked OK.
Finally, I changed the timing belt to no avail. When I disassembled, I found the motor was perfectly in time. My marks from the first change ~18 months ago were still in place and everything lined up. I was able to install the crankshaft lock and cam locking bar with the timing belt in place (it wasn't even off a fraction, the locking bar slid right in). I installed a new belt and all the rollers + tensioner. Didn't put in a new water pump but changed all the other pieces. The new install went great and I was able to get almost exactly the 5mm gap on the tensioner after spinning the motor a few times that Bentley talks about. Put it back together and took it for a spin. DARN!@ The same codes post at exactly 5,000 RPM: P0300, P0305, P0307.
View 6 Replies
I got a 2002 and its giving ma a po301. I know that means a misfire in cylinder 1. I replaced the Coils, Plugs and wires, and now its still there but the check engine light is flashing. What next?????
View 2 Replies
I have a 2008 Hyundai Accent that is giving me one heck of a headache. I keep getting a code for number 1 cylinder misfire. When you start it up it runs fine for a while then the CEL will flash and it will start running rough. As soon as I shut it off and restart it, it runs fine. I even experimented with it this morning on the way to work. It started running rough doing 60, I put it in neutral, turned the car off and then right back on, put it back in gear. It ran fine the rest of the way to work. I have swapped coil packs, fuel injectors, spark plugs, and have even hang tested another ECM. Still number 1 cylinder misfire.
View 8 Replies
2002 Montana code P0304 light was flashing now solid, swapped coils no change, new plug and wire no change, found air box plugged solid from hibernating mice cleaned out thats when light went from flashing to solid still misefire. I've been told its the injector.
View 3 Replies
I have a 1995 ford ranger 2.3 L dual coil packs new plugs, wires, coil packs, tps, idle air sensor, internal temp sensor, and a replaced mass air flow sensor from wrecker. That all said my one son missed a plug when i replaced it , it had no tip left on it , but since then i now have a misfire in cylinder 2 where the olther plug was found and replaced ...
Gap for plugs are .44
Used the wrecker maf to see if it would clear a p0113 which it did. I am stumped on why at approx. 30 minutes of driving that the cel will flash then set a p0302, no other codes no fuel smell. rechecked plugs all are clean haven't been able to check fuel pressure yet, and i out a can of seafoam in the tank to see if it clear out injectors.
Besides all, I will check injector to see if I hear anything but I'm stumped. Also we have to have an emission test so is it best to fail the test and will it show me what I'm missing.
View 14 Replies
I have a 2004 Jetta 1.8t 6speed, I recently bought it from a person(my first VW ever) so just trying to fix some things on it, One thing that I'm stuck at is My CEL, it keeps flashing the code P0501 and some random misfire on my cylinders, I have reset it and they keep coming back.
when I put about 10-15% throttle it revs up fine, no misfire or hesitation until the fuel gets cut off around 5500, which is 1k below factory red line, does not hit a thing like the rev limiter where it pegs off the top multiple times just fuel cuts off.
If i put anything above the said pressure the car then begins to misfire and lots of hesitation and that's what causes those codes to go off.
I've been reading many things pointing towards the engine speed sensor or the wiring. Occasionally my fuel/temp gauge quit working but I believe that is a separate issue all together.
So really trying to narrow down what is actually causing my engine to hesitate at low rpm.
Also i might note when I'm in neutral I can go wide open throttle and the car revs fine until the cutoff and only does the bog down when it's under full load. It sorta feels like the possible misfire is due to bad air/fuel but really do not know.
View 7 Replies
I know it is a random cylinder misfire code however I started my car in the morning and it was fine I moved it and put it back in my driveway. I started it up later and waited for it to heat up i came back outside 10 min later and my check engine light was flashing and my car was shaking like crazy you could tell the engine was misfiring like crazy. I had under a quarter of a tank but not empty yet. I shut it off and turned it back on and it was still doing it. I drove the mile to the gas station the way it was.
Under partial throttle it was revving to 4500 and over 5, had to let of throttle to make the car shift up a gear. I filled up and started the car again performed fine after that however the check engine light was solid now and still on. I went to my local mechanic and he read that code P0300. I changed my spark plugs that day and they were crap the original spark plugs I have 65,xxx on my car now. Car is smooth now. I cleared check engine when i saw him first and it did not come back on all day even before i changed the spark plugs later that night. Why my light was flashing and why my car was acting like that till i filled up?
View 6 Replies
1997 Ford F150 - 133K Miles - 6cyl - 4.2L. This is a truck that gets less than 2K/year put on it. Has had "issues" with worn bearings and holding oil pressure for a few years now. Yesterday, the check engine light started flashing (as opposed to solidly lit) and the code came back as a cylinder #4 misfire (only the one code). The truck was clearly not firing on all cylinders and at idle, ran terribly (couldn't be driven). I just did a compression test on all the cylinders and all measured around 140-145psi except the #4 which read almost 170psi. I rechecked this a few times as well as a couple of the others and am now sure of the results. What could cause this one cylinder to have a higher compression ? Is whatever is causing this increase in the compression, also be the cause of them misfire ?? I'm stumped here and quite frankly, expected the compression on the #4 cylinder to be really low as opposed to the others.
View 13 Replies
My 2007 Ford F150 Lariat (5.4L) with 82k miles popped a P0307 (#7 misfire) code one chilly morning. It began stumbing and hesitating a bit between 25-35mph, and each time it occurred, the engine light would flash on and off. Hesitation clears and light goes steady. Cleared the code and didn't see problems again for a month...until the next cold day (freezing temps). Popped again and hesitation returned. Ford dealer wants to change plugs. I've read coils can also cause the issue. Not sure if I can do either myself.
View 4 Replies
2003 Ranger FX4 Flareside
4.0
Automatic
145,000 Miles
Here's my issue: My Ranger has been running like a dream until yesterday.
I took off on a parts run for my sons Ranger. I got to a stop sign and as I stopped, it started missing and barely running. I nursed it back home and checked the flashing CEL. It was giving me a misfire on #3.
Since I had been planning on changing the plugs and wires, I dove in and got it done hoping that was the cause of the misfire.
Started it up, same thing. I went to the next obvious item: coil. Replace it, still running like crap. Gave up for the night.
Today, I thought I would dig in using the tips here on the forum. Did the spray down...no errant spark anywhere. Tested fuel pressure: 65psi no drop in pressure on acceleration.
Started pulling wires off the coil one by one. Four of the wires resulted in running worse. 2 had no effect. #3 and #6. The coil was producing plenty of spark on all 6 ports.
At this point I was sure it had to be 2 bad injectors. Since I couldn't get injectors tonight, I moved them around after cleaning them a bit and tried my wire test again. The problem stayed on the back 2 cylinders!?!
I tested for voltage on the back injector plugs and I am getting voltage. I also used a stethoscope to listen to all of the injectors. The back 2 seem to remain silent. I have also unhooked the battery for 20 minutes to reset the PCM. Still missing and running rough....
Here's a list of what I have done:
Autolite Double Platinum APP5144 plugs. .062 gap
Autolite Pro Series wires #97051
BDW E97P Coil
New air filter
What should I do next? I really don't know where to go next.......
View 8 Replies
I have a 2002 Ford F-150 with a 5.4 Triton. 212,xxx miles. I replaced the cops and the plugs about 6 months ago. I was pulling a trailer up hill last week and the engine was under a load doing about 3000rpm. It began to misfire and give me a flashing mil. However, before I went very far the engine began to run fine. It happened 3-4 different times. However, there is no code recorded. I've driven the truck nearly 100 miles with no problems, but I'm going to be pulling that trailer uphill again next week.
View 8 Replies
OK, quick question. I have an '03 250 with the 5.4 and the OD light began flashing tonight. I looked in the forums here and everyone say's new tranny or sensor but over on the diesel forums the are saying that the alternator is a big cause of this (dirty power).
At the beginning of this year I noticed what I assumed to be a misfire when putting the motor under a load. Once up to speed it would smooth out and all was good. I was told that a plug job on these trucks is hellish and expensive since a lot of guys break the plugs off in the block. I put it off and the issue went away when the weather warmed up.
Now it's getting cold again and the misfire is back. Driving home tonight the truck died at a light. I restarted it and as I accelerated I noticed a difference in the shift from first to second and then saw the OD light blinking.
Again, the diesel guys are all talking alternator so my question is this: could the alternator cause both the OD light to flash AND the misfire? If the "dirty power" can cause the tranny to fall in to safe mode, can it also cause the ignition to be problematic?
View 4 Replies
My truck is an 2003 2500hd with the 6l engine and 89k miles. From time to time I'm getting message "reduced engine power". Usually at the morning after 10-15 minutes after starting. I have to pull over, shut it off, wait few seconds then restart it. The ses light goes off usually by end of the day ( or after few hours ). When scanned by chevy tech showing code P1516 Throttle Actuator Control (TAC) Module Throttle Actuator Position Performance. I have new battery with new main cable. TAC Module was cleaned.
View 14 Replies
