Silverado :: 1994 Chevy - AC Compressor Engages But No Cooling Really At All
Oct 15, 2012
The issue I'm having is the A/C. When I got the truck the A/C was completely freezing. Recently however, the compressor was having issues not engaging and I fixed that by simply plugging the cord to the accumulator thing. . Now the compressor engages, but is not cooling really at all. It is an old truck and the compressor is a little worn from what I see maybe 2mm space when not engaged. I checked the levels of freon/coolant with a gauge and the amount is perfectly fine. Plus there seems to be no leaks.
View 1 Replies
Advertisement
'07 Silverado with 38k (maybe I don't drive it enough). Recent problem when approaching a stop where the ABS appears to engage. Pulse is felt in the pedal and it obviously increases the stopping distance. Does this about 40% of all stops and between 5-10mph approaching the stop.
Haven't rear ended anyone yet, but on dry 100 degree Detroit pavement, I wouldn't think the ABS would be engaging prematurely.
No error codes with a OBDII scanner and the brakes appear to operate and are otherwise smooth. And I flush my brake fluid annually.
View 5 Replies
1983 chevy c10I bought this old truck about a week ago and I noticed a few things right from the start. Engine revs kind of high before the transmission engages (about 1,200+ rpms).at highway speed the truck shakes and vibrates really bad at times. the steering wheel doesn't vibrate so I dont think it`s ball joints or tie rods.The truck barely goes backwards when in reverse, the engine revs high (over 2000 rpm) but the truck barely moves backwards.It almost feels like the emergency brake is on.
yesterday the truck (transmission?) started slipping and then it stopped working. I was stopped on the side of the road and this old guy stopped.I told him what happened and he said it was probably the transmission but he knew a way to get it working again long enough to get me home. He picked up a handful of sand from the side of the road and put it in the transmission dip stick hole and then poured half a bottle of brake fluid in.He said the transmission is gone anyway so the sand and brake fluid wont do it any more harm.The truck ran again but not far enough to get me home I had to get it towed. Now I am wondering if it really was the transmission and not just the torque converter. I guess it doesn't matter now because the transmission is probably toast now.
View 12 Replies
I have a 2002 Ford Explorer with AC that is not cooling. The AC clutch engages, then cycles off and repeats the process over and over. With a gauge on the low side port, the pressure rises to around 65 psi when the compressor is off, then drops in seconds down to nearly 10 psi. Does this indicate low AC pressure? I have always seen the pressure pretty much stay static at a certain pressure....haven't ever seen it fluctuate like that from low to high as the compressor kicks in and out.
View 2 Replies
Weird A/C issue that started yesterday. Had ac on all morning, start my car after lunch, a/c runs for a few seconds, hear a squeak (like a belt sticking) no more a/c. Moving the temp knob makes no change just all hot air. Both fans engage, compressor and what I believe is the clutch engage, hoses get cold, and no CEL's. Really stumped here.
View 3 Replies
Ok I am at my wits end with this. I have a 2000 Mustang GT 5-speed with 80k miles. When the A/C is on it will occasionally misfire at steady, low (between 1-2k) RPMs and will have a fluctuating idle as well. Occasionally the fluctuating idle is bad enough that it stalls out. It only does this when the compressor is engaged. It sounds like a vacuum leak, but I have checked and cannot find any sort of vacuum leak. Also, it throws a P0300 (Random/Multiple misfire) code. When the A/C is off it runs like a charm. Here is everything that I have done...
Replaced COPs
Replaced spark plugs
Cleaned MAF sensor
Cleaned IAC valve
Replaced fuel filter
Replaced fuel pump (unrelated to this, the old one just died)
Ran seafoam through the motor
New battery (again, unrelated)
and maybe some other stuff I am forgetting
Also, I have taken some readings:
Fuel pressure @ idle ~32psi
Vacuum @ idle ~17in Hg
Had alternator tested - OK
Pressure in A/C system checked out OK (though I did use one of those AZ cans with a gauge on it, not sure how reliable that is)
Also, the A/C works great. It's like an arctic wind in there.
I am at a total loss for what to do. I would suspect it's something with the motor that is simply exacerbated by the added load of the A/C but I suppose it could be the A/C compressor? Is it possible that it needs lube? Doesn't the freon lube the compressor? (The pressure indicates it's fully charged and the A/C blows cold AF) ...
View 1 Replies
I've got a problem with my AC Compressor, with the AC on the compressor engages then disengages about every 5 seconds. Now I looked into it and some people said you can remove a washer to remove a gap. Do you think I should change the whole unit? Looked online and I can get one for $100. If I do work on the AC compressor to try and fix it or remove the whole unit do I need to drain any refrigerant etc etc. I have a hayness repair booklet and they said that to remove the ac compressor you need to get it drained by professionals. Although on the compressor I only see a electrical plug and no hoses.
View 14 Replies
I have a 98 chevy truck that won't start. After it sits. It was starting after cycling the key a few times. But now it won't start. Could it be the pump? I hear it running.
Or could it be the regulator? It was running good after it started. No check engine light, no gas smell, and no rough idle.
View 6 Replies
Looking to get the A/C working on my '78 F150 with integral (factory) A/C system. It is complete, but it seems to be blowing warm air as opposed to cold.
When I turn on the A/C, the compressor engages and the blower switches to the dashboard vents. I waited for a minute or two, but no cool air.
The sight glass has a silver line running through it. I assumed this was full? It would be black if it was low/empty.
View 6 Replies
A high pitched squeal appears to come from the front of the a/c compressor whenever the clutch engages. When the clutch disengages the compressor stops spinning, and the squeal stops. I can watch and listen to this as the system cycles with the a/c switched on. If I turn off the a/c, no squeal. I'm guessing the bearings in the compressor are going out. However, the system still cools normally, so apparently no gas has leaked out.
Does this imply the compressor must be replaced, or could injection of some oil into the system possibly fix it...?
This car only has 73,000 miles on it. I've owned 2 other TB's and a couple classic Mustangs with much higher miles and never seen an a/c compressor bearings fail.
View 1 Replies
The cruise control on my 2002 Chevy 1/2 ton Silverado doesn't work. Went to boneyard and bought a module but it didn't fix my issue. Borrowed a multimeter and tested the cruise control module plugin. The only pin that came up with a incorrect reading was the first brake test. It's suppose to have 12 volts with brake pedal up but showed about 30, so I changed the brake light switch. Still no cruise control.
Since I have a high reading on the brake pin, do you think I have a wire issue there or would my problem be in the multi switch wires by the steering wheel?
View 2 Replies
I have a 92 chevy truck with a 350 engine that came out of a 93 chevy my problem is my module in the distributor keeps going bad when i spoke with the previous owner of the motor he told me that he had the same problem and advised me to change the distributor. So I took my distributor out of the original motor and put in but the problem still exist, also I have noticed that I have nearly twice the exhaust coming from the drivers side tail pipe as I do the passengers side.
View 1 Replies
On my 1999 Chevy Silverado Z71, a gurgling water sound is present everytime I accelerate. Are there any other Chevy owners that have had this same problem? If so, how was it resolved?
View 14 Replies
I have a 1993 Chevy Silverado, 350, 2WD. It has a 4L60E transmission. I just started having a problem shifting from 1st to 2nd. When accelerating the RPM's go way up and won't shift until I let off the throttle. Then it shifts into all other gears normally.
If I accelerate slowly. it will shift into 2nd at about 16 MPH. It will then shift into all other gears normally. I have replaced the Throttle Position Sensor, flushed the transmission and replaced the filter and fluid. This made know change in performance.
I am now suspecting that it might be the 1-2 shift solenoid. The check engine light is not on and everything else works fine.
View 1 Replies
I have a 98 Chevy truck with a 4L60E. It has no second gear. I was sitting in park for about 10 minutes with the engine running, then put it in drive and it never shifted into second. It felt like it went straight to 3rd. I played with it manually until I figured out I had reverse, 1st, 3rd, 4th and torque converter lockup, just no second gear. My acceleration rate was medium and when I reach about 27-28 mph it would shift from 1st into 3rd. It has 230K on it so I rebuilt it with all the typical parts - frictions, steels, band, sun shell etc., still no second. I then pulled the pan back off and replaced the spacer plate and put in a shift kit. While I had it down I put a corvette servo in and did an air check. It worked fine. I could feel the band tighten.
Both the 1-2 and 2-3 solenoids checked good at 23 ohms. I swapped their positions to see if it would make a difference. I also checked to make sure the 1-2 accumulator piston wasn't stuck in its bore, the spring was new from the shift kit. It was fine. Put it back together...still no second gear. When I originally pulled the pan off for the rebuild, the pan was free of any debris and was very clean. I then drove it a couple of miles to a local transmission shop. They put their scan tool on it and drove it around the block. There were no codes and the ECM was calling for second gear. It doesn't sound mechanical since almost all the parts have been replaced, rebuilt or inspected that affect the 1-2 shift. It sounds electrical. Is there anything I have missed?
View 14 Replies
I have a 1993 Chevy Silverado rwd automatic 350 5.7. It died on me on the way to work this morning. It slowly lost power and acceleration. The lights and radio all worked. When I tried to restart, it tried to start but then just cranked like it had no fuel or spark.
I had it towed home and checked the following things. I removed the fuel filter, it is clear. I verified that the fuel pump was working by turn the key to the on position while the filter was off. Good stream of fuel. I verified that there was fuel to the TBI. Good spray while cranking. I verified that there was spark by pulling a plug out, connecting to the wire and cranking the engine. Spark seemed weak but there was spark. The front plugs were dry, but the rear plugs, especially #8 was very wet. I verified the timing by pulling the #1 plug, removing the distributor cap and checked the rotor position. I bumped the engine to get the #1 piston to the top of the cylinder and the rotor was point directly at the #1 plug wire. The cap, rotor, plugs and wires are only 1 month old.
I also tried to check the ignition coil by disconnecting the coil wire from coil, and slid the boot back to expose the contact. I held it just of the coil while the engine was cranked, but did not actually see a spark at the coil. I did not hear any arcing. I pulled another plug and checked for spark. Again i had spark. Just seems weak to me. I am on my way to the auto parts store to get a new coil.
View 3 Replies
I picked up a very clean 2008 Silverado 2500 HD. W/60K miles. The vehicle has been very well cared for as I know the orignal owner. I have zero complaints with the truck other than an annoying front end clunking. Its very reminiscent to the intermediate shaft issues of my 2003 2500HD.
Basically when hitting very small road imperfections, I can feel/hear a clunking in the front suspension. I can also duplicate the issue by rocking the truck left to right with the steering wheel while going 20-30MPH. I figured, stabilizer links. I put the truck up in the air, & can't find a thing wrong. Links are tight as well as the ball joints & tie rod ends. Were these trucks know for a common clunk like this.
View 14 Replies
My dad's 1996 Chevy Silverado will not shift into hi gear. The truck starts up fine and he can drive it but for some reason it won't shift into hi gear. Him and I are clueless as to why it won't. He has a 1996 Chevy Silverado, 6.5 liter V-8 automatic transmission, and its a diesel. We really want to fix the truck ourselves so we are trying to avoid taking it to a shop.
View 2 Replies
I have a 1999 Chevy Silverado 1500 extended cab. Two nights in less than a week, my horn has went off in alarm mode. Is there another reason for this other than an attempted jimmying of the lock? I live in a decent neighborhood with lots of pole lighting. Someone told me the keyfob battery was dying but I don't have the fob.
View 1 Replies
I have a '99 Silverado 1500 with a 4.3L V-6 amd 188,000. It picked up a problem recently that's been stumping me. Occassionally, and for no reason I can sort out, it starts to shimmy badly. This behavior has come about at several speeds. Sometimes just cruising down the road at 35-45 it starts to shimmy and wobble and the steering wheel shakes as if a wheel is horribly out of balance. Other times this occurs at highway speeds - it's noticeable and alarming. The problem can last a long while; othertimes the symptoms disappear in a few seconds. The first time it happened I thought I had a flat or was about to lose a wheel - this is not a subtle problem.
I've checked several things and came up empty. No delamination in the tires and nothing out of round, but just to be sure I had the wheels balanced and rotated - the balance was spot on when checked. Alignment is good. Did those things, but the symptoms continued. The vehicle is high mileage so I put in on the lift and checked the front-end. The steering rack has a very slight amount of play and the hub bearings have a very small amount of play too - I'll get after those, but they're not causing this intermittent problem. Everything else is tight. Shocks are fine, brakes are fine, I checked the rear-end as well - everything is straight and true. Air pressure is set correctly. I checked the driveshaft for runout and play - that's not the problem. The truck has never been in an accident and nothing seems misaligned.
The truck drives like a new truck most of the time, then suddenly, on a smooth road, it starts wobbling around. I'm starting to believe the problem might lie under the hood. I had a problem some time back with misfiring and the truck bucking - this turned out to be a worn distributor. A new distributor, rotor and wiring solved that problem. But these symptoms are not similar - this is not a bucking problem; the entire vehicle starts to shimmy and wobble with the steering wheel vibrating back and forth. It's hard to tell, but I cannot detect any misfiring or rough running in the engine when these symptoms appear and I have no 'check engine' warnings.
Are there any engine/transmission/drivetrain related issues that could cause intermittent symptoms that feel like an out of balance condition? A few other facts:- I have noticed the truck is a little down on power lately- The fuel economy has dropped off - I used to do around 20, now I'm down to 16mph highway- (Very) slightly rough idle
View 5 Replies
I have a 2000 Chevy silverado. I recently was having problems with the transmittion not switching correctly. Long story short the shop told me to fix the problem I had to put in
A new transmition as well as a new computer which I did, from another Chevy. It worked for a few days then The truck was not starting and had security light on. Had alarm specialist take look and he said the computer had to be reprogrammed. It was reprogrammed at merles. And was still not working. Its unable to start, starts at random once in a long while. ignition switch was changed and still gave same problem. Took to another shop they had a specialist take a look and he said the computer had to be reprogrammed again.
Also would it be possible to bypass the anti theft system by adding a remote start, or cutting some wires. I just really need to get this truck running.
View 14 Replies
