Silverado :: 1992 Z71 Truck Won't Stay Running
Jun 21, 2013
Drove the truck one week ago today and it ran perfectly fine. Drove it last night for about 20 minutes - ran fine. Drove it again today just 1 minute up the road - ran fine. Started it again this evening and drove it 5 minutes down the road - ran fine. Stopped and put gas in it - now it's not fine. After putting gas in it it refused to start but will turn over. Put a booster pack on it and it will start but would only stay running with the gas pedal pushed all the way to the floor, as soon as you took it off it dies. Now it will not stay running even with the gas pushed all the way down.
View 5 Replies
Advertisement
I have a 92 chevy truck with a 350 engine that came out of a 93 chevy my problem is my module in the distributor keeps going bad when i spoke with the previous owner of the motor he told me that he had the same problem and advised me to change the distributor. So I took my distributor out of the original motor and put in but the problem still exist, also I have noticed that I have nearly twice the exhaust coming from the drivers side tail pipe as I do the passengers side.
View 1 Replies
1992 Honda Civic Starts fine but kills as soon as you release the key. Hold the key in the position with the starter motor running and it keeps running. In the old days we would replace the resistor on the firewall. Today?
View 3 Replies
why my truck is running rough the problem I am having is when you push the gas peddle more than a 1/4 of an inch it shudders and has no get up and go and also if say I'm doing 40 MPH and hit the gas you can hear the engine rev up but I will lose all power and actually lose speed I thought maybe the cats were bad and I changed the plugs for good measure but I can't seem to figure it out also I had the fuel pressure checked and its pulling pressure is great/
View 6 Replies
My Dad has a 1992 Toyota Pick-up with a 22RE engine it is a 2 wheel drive automatic. The truck stopped running while idling, he did code tests on it and they came up clear. He can get it to run on propane but not on gas. He did change all the spark plugs, distributor cap and rotor, and spark plug wires.
View 13 Replies
I have a 92 ranger 6cyl 4L. The truck stopped running while driving then kicked on again, it did this several times over about 20 minutes then finally died and now I can't get it started. I recently replaced the fuel pump and filter and spark plugs and wires. I get spark if I ground the plug and some gas will pour out of the fuel pressure test valve when I stick a screws driver in. When I check engine codes I get an all pass. Truck will turn over and sometimes run for 2 or 3 seconds but that is it.
View 2 Replies
Began doing this on sunday and just finished up last night. Truck starts and runs for a bit then stalls. Here is what I did in this order:
1.) Washed truck sundday with purple power and a garden hose. I washed the wheel wells frame and underside, but DID NOT wash the engine at all.
2.) Painted the frame and wheel wells with black paint.
3.) Applied 1/2 gallon or so of fluid film all over the bottom of the truck everywhere I can. Again NOT the engine bay.
Where to start. When it stalled, I can restart every time by waiting 3-5 minutes. It was 13 degrees F last night, so i suspect fuel lines may be freezing but not sure.
View 5 Replies
I Have a 2002 F 250 That I recently changed the fuel pump. and now I'm having a tail light problem. when i start the truck, my tail lights and plate lights comes on (dim). if i turn my head lights on the truck stalls out. if i step on the brake or put the truck in reverse it stalls out. if i put it in drive it runs just fine. i checked my fuses and relays and the problem is still there even when the relay and fuse for the lights are out. when i turn the truck off all the light go out.
can't seem to find any info on this problem anywhere.
View 3 Replies
I Own A 92 Chevy Silverado, 154 K Miles. Runs Great! My Problem? I Experience Rough Shifting At First Take Off, After She Warms Up The Shifting Is Smooth. After Parking And Starting Again, Rough Shifting With A clunking Sound.
View 9 Replies
I have a 92 chevy pick up 5.7 with 159,000 miles. The truck runs and starts great but shortly after I bought it 3 years ago it developed a sort of misfire at higher rpm's, it's fine if I drive it normally but if I try to pass someone it will downshift then fall on it's face, (spit,sputter and slow down). some times I can feather the accelerator and it will come back again. I normally don't drive the truck in the winter but this week I was forced to use it and the cold weather is seriously affecting it, it took forever to get it up to 70 mph after getting on the highway. once up to speed it will do 75 all day without an issue.
I've replaced the plugs, wires, pulled the throttle body and cleaned it as the port for the pcv valve was plugged solid with carbon. I have not replaced the cap and rotor as they seemed to look fine. I have not checked the fuel pressure because it will break the tires loose upon take off and I don't think that would be possible if the pressure was low, would it?
View 5 Replies
I have been having some recent issues with my 92 bird lately. It started minor but now the car will not stay on. It originally started out as I would need to press the gas to get it to start and it would stay on, but now if I let my foot off the gas for anything it will just idle rough and die out. I took it into a shop and they said that I had a bad idle control valve and the pigtails need to be replaced. They also said that some wires were shorted out and they would replace those as well. They replaced the Pigtails and the idle control valve and the car started to work fine again, for about 4 days only. I drove to the store and when I came back out to start it back up it wouldn’t stay on unless I gave it gas.
I had to drive it home giving it gas and using my other foot on the brake so that it didn’t due out. I checked the job they did and doesn’t even look like they did what they said they did. I looked at the botched shrink tube job they did and it just doesn’t look that professionally done. I did call the guy and he gave me an excuse and said that they short must have traveled further and he was surprised that the car was even running when they were done. I of course just hung up the phone after hearing that. I did a little looking around the engine and I noticed that if you unplug a vacuum tube and press on the gas and hold it at 2000 rpm for a few seconds and let off the car will stay on, but the moment I plug that hose back up with my finger or plug it back in the tube slot, the car idles rough for a few moments and dies.
View 6 Replies
I have a 1992 volvo 940 about a month ago I started noticing a burning smell and it was my brakes, they also make a squeaking sound and I took it to my mechanic upon which they will need to be replaced. Today I notice my battery,brake and system lights all came on and stayed on while I drove about 4 miles. Can something to do with my brakes needing repair?
View 5 Replies
I have a 98 chevy truck that won't start. After it sits. It was starting after cycling the key a few times. But now it won't start. Could it be the pump? I hear it running.
Or could it be the regulator? It was running good after it started. No check engine light, no gas smell, and no rough idle.
View 6 Replies
I am having a bad time with my 2006 2500HD 4x4 with the 6.0. First the battery was beginning to act like it was running down, getting weaker and weaker every time I started up truck. So finally truck died at the gas pump. I pulled battery (optima red top), and took it over to NAPA to test. Battery tested fine on top posts, but was acting funny with the side posts.
So, I purchased a new Redtop, and installed and and clunk, truck wont turn over! So, back to Napa to buy a new starter, install starter, hook up battery and now the sucker turns over great but will not start at all. Truck threw 6 codes: P0335, C0035, U1026, U1041, C0040, C0055.
Wiring all looks fine, battery looks new, and I have changed nothing but battery and starter.
View 4 Replies
I have a 1997 Chevrolet Z71 4x4 truck. 350 engine.
This morning I went to start the vehicle and it cranks fine but doesn't turn over. It cranks at a normal speed and then every second or so struggles, and then cranks normally again. About 2 weeks ago I went to start it and the starter didnt engage, it just spun. I released, tried again and it started right up. It did that twice over about two weeks. I figured the starter had gotten too weak, so I replaced.... No change.
The truck has been running quite rough for a little while, and I was doing research to replace the valves and sensors that were recommended (EGR and Idle Air Valves), but the truck seems to have decided that I will do this maintenance now, whatever it is. By running rough, I mean, when it idles, it shakes some. Going down the highway, it runs fine and doesn't miss or anything like that. It is sluggish, but it is a 16 yr old truck with 230000 miles, so it just seemed somewhat normal.
I have checked for spark, and verified that. I can smell fuel when I crank, so I don't think its a fuel problem, although tomorrow I will see if it will fire off starter fluid to verify. I have had the rotor go out before, but it seems when it did that it didn't stagger when I crank.
View 3 Replies
I got a 99 Silverado z71. Well my problems started yesterday morning going to work when I got to work I tried backing into my parking spot I got to put it in reverse and to start backing up and the truck acted like it was in neutral. So without thinking I shut the truck off turned it back on and tried again and it worked like nothing ever happened. So I thought nothing of it sat there with the truck running since I'm there early I figured I had enough time to go get a bite to eat so I put it in drive And go to pull out and the truck was acting real sluggish taking off in 1st. Almost like it was slipping again restarted the truck and the problem was gone get back to work parked it.
Later that night on my way home on the highway I noticed the truck was shuttering periodically and the rpms were at around 2000 going 65. When the real problem started was when I came to a stop light and go to take off it was really sluggish and slipping pretty bad so I pulled into a gas station stop and restarted the truck and it temporarily fixed the problem tell I was five miles from my house this time it started slipping really bad. I was able to limp it home, I also noticed it skipped 2nd and went into 3rd. What I'm stumped on is why everytime I shut it off and restart it, it acts like nothing happens tell later down the road.
Could it be a computer problem or is the transmission done for?
View 5 Replies
But i have a 99 silverado 5.3l z71(new body style) bought a new key fob to program but my truck will not go into program mode. Ive tried the hold unlock then cycle ignition and the turn signal version but neither one worked....
View 10 Replies
My 2002 4.8L Silverado recently started having this intermittent starting problem.
A few days ago I got in to start it, turned the key and nothing happened. Lights, radio and power locks all were working fine but engine would not crank or turn over. Turned the key off and on a few times and then the truck started fine.
It started fine for about 3 days. Then got in to start it the next day and this happened again. Turn the key and nothing. Lights, power locks, radio all working ok. Turned the key off and on multiple times but still nothing. So I cleaned the battery cable connections and fully charged the battery, even though it checked out ok. Tried it again and same thing was happening.
This time I looked at the ignition and starting relays under the hood in the electrical box. I swapped a few of them around, tried to start it each time and still nothing.
So I had the vehicle towed to the dealership to be checked. The next day the service man calls me to tell me when they went to check it, the truck is starting fine.
I am not sure if this is a starter problem, ignition switch problem or maybe the computer. The thing is, I can't drive it like this because it is no longer reliable.
View 7 Replies
My silverado no longer starts and the fuel gauge no longer reads. so far figured out that there is no power to the fuel pump and sending unit. Looking for an engine wiring diagram for this truck with the 6.0 engine?
View 14 Replies
I have a 2000 Silverado Z71 with a 4.8 and Auto Trans. Here lately if the truck sits for more than a day with out being cranked the battery is dead. Put a new battery in last July. When i put a meter on it the Alt. shows 14 volts out put. once it is cranked it will start every time with no problem.
View 1 Replies
I have a 98 Chevy truck with a 4L60E. It has no second gear. I was sitting in park for about 10 minutes with the engine running, then put it in drive and it never shifted into second. It felt like it went straight to 3rd. I played with it manually until I figured out I had reverse, 1st, 3rd, 4th and torque converter lockup, just no second gear. My acceleration rate was medium and when I reach about 27-28 mph it would shift from 1st into 3rd. It has 230K on it so I rebuilt it with all the typical parts - frictions, steels, band, sun shell etc., still no second. I then pulled the pan back off and replaced the spacer plate and put in a shift kit. While I had it down I put a corvette servo in and did an air check. It worked fine. I could feel the band tighten.
Both the 1-2 and 2-3 solenoids checked good at 23 ohms. I swapped their positions to see if it would make a difference. I also checked to make sure the 1-2 accumulator piston wasn't stuck in its bore, the spring was new from the shift kit. It was fine. Put it back together...still no second gear. When I originally pulled the pan off for the rebuild, the pan was free of any debris and was very clean. I then drove it a couple of miles to a local transmission shop. They put their scan tool on it and drove it around the block. There were no codes and the ECM was calling for second gear. It doesn't sound mechanical since almost all the parts have been replaced, rebuilt or inspected that affect the 1-2 shift. It sounds electrical. Is there anything I have missed?
View 14 Replies
