Silverado :: 1991 V6 - While Driving Truck Seemed To Slip Out Of Gear And Not Go Back In
Jun 22, 2014
I drive a 91 Silverado, v6, standard transmission.
While I was driving my truck seemed to slip out of gear and wouldn't go back in. About 10 seconds later it shut off. I was able to ride the momentum and pull over. It tries to start when I'm turning the key, but nothing. I've ruled out the distributor and the battery. All I can think now is: transmission ....
I've had problems with my distributor rotor from time to time, but no real indication that my transmission was having troubles.
View 5 Replies
Advertisement
Seems lately when driving up a long incline the Trans seems to slip back to third gear from overdrive. I watched the tach and it jumps up like it's went to another gear. But goes right back into overdrive. It will keep doing this as long as we're under load, like going up an incline. If I put it manually into 3rd and keep it there it won't do it.
We went on a long trip last summer and it kept doing it and it threw a tourque converter code. I can't remember which one tho. I did a drain and fill and it made it better but it's doing it again. We have 167,500 miles on it. I was told by Hyundai that it would be around $2800 for a rebuilt tranny. If I was to need one. Don't think the TPS would cause the shudder right? Seeing it doesn't do it when I keep it out of overdrive.
View 4 Replies
97 Silverado - 5.7 with 4l60e trans. truck will not shift into 2nd gear while driving. stays in first gear until rpm are high and shifts into 3rd. under hard acceleration will stay in 1st until let off gas then shift into 3rd. manual shifting results in same, no 2nd gear until selector is moved into 3rd then shifts into 3rd. Haven't got any trans codes, fluid change netted no change in performance, fluid was pretty dirty but didn't smell burned, and there were no metal shavings in pan.
View 9 Replies
Have a 2009, 2500HD 4X4 23K miles that has an occaisional/intermittant trans slip when shifting from 2nd to 3rd (I think). It always seems to catch me by surprise so it may be 2-3 or 3rd to 4th. Shift point seems to be around 1800rpm, engine revs to about 2500 during the slip. It's always shortly after starting up and the trans is not necessarily up to full operating temp. I've noticed it happening in the dead of summer as well as the dead of winter.
View 14 Replies
I have a 98 Chevy truck with a 4L60E. It has no second gear. I was sitting in park for about 10 minutes with the engine running, then put it in drive and it never shifted into second. It felt like it went straight to 3rd. I played with it manually until I figured out I had reverse, 1st, 3rd, 4th and torque converter lockup, just no second gear. My acceleration rate was medium and when I reach about 27-28 mph it would shift from 1st into 3rd. It has 230K on it so I rebuilt it with all the typical parts - frictions, steels, band, sun shell etc., still no second. I then pulled the pan back off and replaced the spacer plate and put in a shift kit. While I had it down I put a corvette servo in and did an air check. It worked fine. I could feel the band tighten.
Both the 1-2 and 2-3 solenoids checked good at 23 ohms. I swapped their positions to see if it would make a difference. I also checked to make sure the 1-2 accumulator piston wasn't stuck in its bore, the spring was new from the shift kit. It was fine. Put it back together...still no second gear. When I originally pulled the pan off for the rebuild, the pan was free of any debris and was very clean. I then drove it a couple of miles to a local transmission shop. They put their scan tool on it and drove it around the block. There were no codes and the ECM was calling for second gear. It doesn't sound mechanical since almost all the parts have been replaced, rebuilt or inspected that affect the 1-2 shift. It sounds electrical. Is there anything I have missed?
View 14 Replies
I have a 2001 2500HD P/U with the 8.1L V8. I have owned the truck for ~5yrs and used it with everything towing. For about the last three years, I have noticed that when the truck is in gear (Either Rev. or Drive) the engine idle almost acts like it is missing. It doesn't do this at higher RPM's (say over 1K) while driving.
Last spring I did a tune up (Plugs and wires) and a few of the plugs had quite a bit of build up so I figured that was what was causing the issue. For about 1wk after the tune up it seemed to clear things up (at least I didn't notice it), but then resurfaced.
My question is: should the "Coil" parts that feed each spark plug need replacing, or could they cause this symptom? The ignition system on this truck is a bit different that what I am used to seeing, so I am not sure where I should start looking for the problem.
Also, there are no error codes being thrown.
View 11 Replies
He has a 2002 Explorer 4.6. The truck is having a hard time going into reverse intermittently, hard shift in normal driving and thinks it has slipped in first gear going up his driveway that is steep. He is worried that he put slightly over sized tires and this may hurt his tranny. The overdrive has blinked twice with in the year. Possible problems that could create this he is thinking solenoid pack, servos, torque converter. The truck has 110k and never done fluids, Would lucas slip fix or hurt we have heard that these tranny's are finicy.
View 1 Replies
The truck sat since 2002 or so. Hasn't ran since, So my brother and me towed it home and I started working on it. I replace the tailgate, Replaced the lights, Did a oil change, Dropped the gas tank out and ran a gallon of gas and seafoam through it. Then I was driving it the other day and I decided to play the radio so I pressed the power button and I heard a pop noise. Like not a fuse pop noise. This happens every time you turn it on/change the volume. Its coming from the speakers and the louder the volume the louder the popping is. Is the radio just bad? Its a funny square shape and I haven't ever seen a radio that would fit this. I checked all the fuses and I found nothing.
View 8 Replies
i have a 1991 silverado k2500 with the 454 big-block in it as i was driving home yesterday getting on the high way the truck just died completely without warning i looked down because i smelled something like burning wires and there was allot of smoke coming from under the dash where the steering column is when i go to start it all it dose is crank and crank never fires up it has no spark at all ?
View 4 Replies
I have a 1991 Silverado C1500 and when I push the heater button to on, the thing just goes absolutely crazy. Instead of one little indicator light, that is suppose to show hot, it lights up all the way across, like a pinball machine that has tilted. The heater air does not get hot and the temp indicator on the dash (separate guage) will not move off of cold. I am going to replace the thermostat, but what is going on with the darn temp gauge?
View 1 Replies
My 2002 excursion 7.3 is acting weird when in drive. I have to get to around 2k rpm to get moving and hard shifts. But if I put it in 1st it has no problem but in 2nd i have hard vibration that shakes whole truck.
View 5 Replies
On my V6 tdi , the converter bypass coupling is closed very late : generally in the third gear arround 2200rpm. In second gear i found that the transmission slip a lot.
View 1 Replies
So long story short, my clutch is not disengaging all of the way, but only sometimes.... I have replaced clutch, flywheel, slave cylinder, new stainless steel clutch line and new clutch master cylinder all within this month. The same issue has been occurring prior to replacing all of this and also after replacing all of this. I've bled the system (with a power bleeder) more times than you can count on both of your hands so there is no way there is air in the system.
More details : The clutch doesn't slip in any gear. Stop and go traffic in first gear is really the only time I notice it not disengaging. I can't pull it out of 1st gear when it happens so I have to shut the car off to get it out of first gear. When it's stuck in first gear with the clutch pushed in (on a flat surface) and I let off of the brake the car creeps forward. Not at full speed like if I were to release the clutch pedal all the way but its still semi engaged enough to make the car move.
Replacing everything theoretically should have fixed all issues, but it hasn't. The only thing I didnt replace was this piece of the factory clutch line.
Tomorrow I am going to take the stainless steel clutch line and run it straight to the clutch master cylinder bypassing that weird silver box and hope that fixes it. As a side question what does that silver box do anyways?
View 12 Replies
2004 silverado, 2wd, V6, 150,000 miles on it. New plugs and wires 2 years ago. New fuel pump and fuel filter last summer. Truck was running fine but I did notice the last couple of mornings while I was driving the headlights would dim a little bit then go back to normal. Yesterday afternoon it started like it was 15 below out. Turned over kinda slow. But it wasn't that cold out. Anyway the headlights and dash lights were really dim. I got the truck in the driveway, revved the engine and they didn't get any brighter. The truck started running ruff and eventually quit. When I tried to restart it, it just clicked. When I turned the key off the dash lights got bright again.
View 5 Replies
I have a 98 Suburban with a 4l60e rebuilt 13 months ago, less than 15000 miles since. I have no second gear at all, but still no apparent slip at all in fourth. R,1,3 are fine. The fluid is a bit dark red, smells normal. There was a bit of the grey paste on the magnet but no obvious trauma. I did find a very small copper wire in there. It's about a 22 gauge, looks like it could have been a 3/8" ring or retainer.
I've replaced the servo, and of course fluid and filter. I pulled off the housing for the 1-2 piston but didn't have the right part to replace. I did not see anything cracked or cocked, it came out and went in fine. The main o ring did look fairly warn, but seemed all-right.
A transmission tester showed second gear being called for on a test drive. I did get a P1870 slippage code a couples weeks ago, I have since cleared it and it has not returned. Could the copper 'ring' be a retainer for something related? I'm guessing the solenoid, but I believe it also applies to 4th gear.
View 8 Replies
Having a very pronounced hesitation/slip between 2nd and 3rd gear shifts. It happens in both "D" and "S" modes. I've had the tranny flashes and they fixed the throttle hesitation and the general harsh shifting. Still have a slip when going from 2nd to 3rd.
View 5 Replies
I own a 2002 W8 passat b5.5 that had issues from the used car dealer i had bought it from. I had 2 new motors installed over the period of about 13 months . The first motor had a bad torque converter and seemed to also cause my trans to slip. I am not sure if that is the direct cause of the trans slip going from 2nd to 3rd gear. The second motor dropped 4 valves in the cylinder "3" and cracked the starter. I had all the work done by the VW dealer that i used to work at.
As of today i seem to hear a knocking from idle to 5,000rpms, which is the highest ill push it. Now I know that a lot of of the W8 had issues with the torque converters. my current engine has just about 4k miles on it and I know vw warranties this motor up to 12k miles. That is not my concern, my concern is why do these motors keep failing under normal every day use in my particular vehicle?
View 2 Replies
Got a weird problem with my 2008 2500HD 6.0L silverado. The problem is more noticeable within the first few miles That I am driving it. The cluster will basically power out for a split second & come back on. I notice it from the sound of the stepper motors all dropping off, then all the indicator lights illuminate & the gauges go back to the normal readings.
After this power cycle,the airbag light will be lit, & I will have to unbuckle, & rebuckle. then the airbag light will go out. I have a feeling if this isn't a common issue, its going to be a tough one to find seeing it happens so intermittently.
View 2 Replies
RX 350 (mine is 2013) produce a slight bump in revs as you decelerate moderately going from 2nd gear to 1st? It goes away after the tranny is warmed up. Wondering if it's just a result of the cold weather.
View 5 Replies
I got a 2000 ford explorer with 151k on it... Since iv had the truck (5yrs) its always had a slight slip around 3rd going to 4th. The tran is auto!!
I use to be able to jump in and take off but here lately i have to let the truck idl for a few sec or up to a min before i can take off (warm or cold). This just started a month ago...
The trans fluid smells burned and it has be 2yrs since iv changed fluid and filter in the tran...Everything other then that iv kept up to par. What do you think should i start looking for something new or just change filter and fluid????
I know the truck has had a good life so I am starting to think the tran maybe trying to go.... My friend has a 85 dodge ram charger suv not sure the miles but its auto as well....It has a 318. Other then a small dent the thing look good... It has some kinda vacuum leak major but doesn't effect running. He told me the leak is from something he had removed when we left CA that they said he had to have for smog?
View 3 Replies
I have a 2005 Passat TDI with 2500 miles & this car was wrecked and I recently got it back from the body shop. Well I now have a transmission problem. When I first take off the car feels like it is in a high gear. Then the transmission will slip. I have taken the car to the local VW dealer and they have given me the following information.
-Incorrect Ratio 4th gear #Code P0736 & 17110
-Incorrect Ratio 5th gear #Code P0735 & 17118
This leaves me with two options according to VW.
1. Replace the transmission
2. Replace the computer
2005 Passat TDI? Which would be more obvious as a problem?
View 1 Replies
