Sierra :: 2006 GMC 1500hd - No Reverse / Won't Move?
Nov 14, 2012
I have a 2006 gmc 1500hd with the 6.0l the tranny went on it so we replaced it with a brand new one that was installed by a dealer, well it works fine except when you go out in the morning and go to back out of the driveway it wont move but if i put it in park and let it warm up for 10 min and try again it works fine we have had it back at the dealer to have it looked at and they said its fine so i took it somewhere else and they said its fine. ive changed the tranny filter and fluid spent about a grand having it looked at and cant figure it out
View 2 Replies
Advertisement
I have an 06 Montana sv6 that clunks when I start to move forward or reverse. Not when I put it in gear but as I start to move. It also does it when I take off from a stop sign. It doesn't make any noise while driving or turning though.
View 1 Replies
I have a 2008 GS350. Been having brake clicking when I move from reverse to drive and lately been happening more when driving regularly. Brought it in to Lexus to get the complimentary 19-point inspection and they said I needed new brake pads and rotors. I did do a search and found it can be issues with front spindles, sway bar, bushings.
View 5 Replies
I have a 09' 4cyl automatic engine with 54k.
About 30min ago when when I parked the shifter would not move past neutral into reverse and go into park. I can go from D into neutral or the next slot over for manual shifting. Naturally this causes a problem as you can't take the key out of the ignition if its not in park.
I took a screw driver and popped open the cap for the shift release button and used that to move it into park. Turned car off, back on, etc etc seemed fine. So when I tried moving it into reverse and it wouldn't budge. It instead would make a electronic click or snap coming form the steering column but more back toward the engine. Like more into the dash area but back in it. It would make this noise every time I attempted to move it but it wasn't a continuous sound. Just once with each jerk to the side to move it out of park.
So the car works fine except for this. I used it with the screw driver/shift release to unlock it and it drives fine. Goes into reverse and back in park but if I move it into neutral or drive it will not go back into reverse or park.
View 1 Replies
I'm new here and I am having issues with my Lumina. It is a 93 Chevy Lumina Euro 3.1L 6 cylinder and has 192K miles on it. It has had one owner for the past ten years that I know for a fact.
Here's what happened. I was coming back home (2hr trip) The brakes had started making that roaring sound on the way down and had gotten worse when I got ready to make the trip home. Okay so I know the brake pads needed to be changed. No big deal. Well going down the road at 65mph I round a curve and my car starts making this REALLY LOUD grinding clattering noise. It took me forever to get it stopped. I will still in the road and I needed to get it out bc it was right around a curve. So I put it in drive and it wont move. So I put it in reverse and it moves just fine with no problems and no noises made. After backing it out of the road I tried to put it in drive. It moved forward a few inches and stopped like something was binding it up.
So here's the problem.. it will move in reverse with no problems at all and only creeps a couple of inches forward then stops. The harder you press on the gas the more it tries to lurch forward but will not move.. like it's caught on something.
We changed the rear brakes on it. Discovered that the driver side rear rotor and caliper were broke beyond repair so we replaced those too. Still the same.. moves forward a lil bit and stops but will go in reverse just fine. We don't seem to think its the tranny bc it pulls hard and seems to not have any problems pulling.. but its like something is bound up somewhere. That is the best way I know how to explain this situation.
View 8 Replies
My trailblazer will not move in reverse , and will barely move forward, i checked transmission fluid hot and it's not even on the dipstick but when it was cold. it was?? Do I add more or what?..
View 9 Replies
My passenger side power mirror won't move up and down anymore. It started out just moving very slow, now no moving. Side to side works fine, power folding is fine also. Does the up/down motor is replaceable or do I have to replace the whole mirror.
View 2 Replies
I have a 99' GMC 1500 Sierra SLT w/5.3 Vortec V-8 w/460,000 miles (yup !!) I bought the p/u w/59,000 miles, and the gear-selection lever on the column has always been hard to move when selecting gears. My daughter drives the p/u, and is hard for her to select gears.
View 1 Replies
My truck out of nowhere will start to idle low and die when put in reverse or drive then on other days sometimes it will start and run right. I got the code 44 witch it could be a o2 sensor but tomorrow I'm getting my catalytic converter took off and run straight pipe do I still need a o2 sensor without a catalytic converter or what's causing lean exhaust?
View 9 Replies
All the sudden today all the dash indicators died & the seatbelt indicator light is flashing. It drove OK, but something is definitely wrong. Fuse maybe?
2013 GMC Sierra 2500HD Duramax Diesel.
View 3 Replies
I have a 2003 Chrysler Town and Country and my problem started with no reverse after starting car. If I pushed it back and drove forward 10 or 15 feet then reverse would work fine and shift properly. As long as I could drive forward first then reverse would work. This was like this for a few days then the vehicle wouldn't move at all. There wasn't any error codes. The fluid is full and clean.
When the van was about a year old I took it to the dealer with harsh shifting and they said there was a broken wire to the trans, I am thinking this is when they came out with the 3 wire slice people where talking about.
I wasn't needing the van so it has been sitting now for almost a year. Now I want to get it working again...
View 1 Replies
My 2002 lincoln ls v8 140k miles doesn't move when put into reverse or drive 5 or even d4,3,2,1 , it just starts to roll back/forward when taken out of park. It has the gear selector with d5, d4,3,2,1 not the select shift. I was told needs new transmission, but before it stopped moving completely it was still driveable second slipped at lower speeds(mostly when looking for parking or in traffic).
I had made an appointment to bring my car to the shop and the same day is when it stopped moving. All this happen within a week during the week i constantly got an e where d5 was and on last day check engine light came on.
View 4 Replies
Last night when accelerating from 40 to 60 mph I felt a "whoosh" and then the RMPs went to 3000 when I had my foot on the pedal. They dropped to 1200 if I let off. This morning the car would shift into reverse, but punching the accelerator did nothing. Other gears are fine. I rolled out of the drive, stopped at the mech and diagnostics showed only a bad speed sensor. I saw a post elesewhere that had a similar issue in 2006, same model Toyota Sienna 2000 xle. Mech pricing the transmission replacement. Could it just be malfunctioning speed sensor sending bad data to the ECM?
View 1 Replies
2004 BMW 330i 140k miles.
We first noticed this problem a year or so ago. At first, it happened only on cool mornings if the car had been parked outside. The cold car would require 3-4,000 RPM to move, forward or reverse. After about one minute or 3-4 blocks, the transmission worked perfectly at the touch of the throttle for the rest of the day.
It only happens about half the time. Other times, even if cool and after being parked for days, the transmission engages normally from idle and up.
Once recently, it deviated from this pattern. After sitting overnight, it started and pulled into the garage normally. I shut it off for a couple of minutes to place ramps in front of the tires and restarted the car. It did not want to move on the second start. It took 3500 RPM to climb the ramps. That was scary. The car has never suddenly engaged, but if it had suddenly engaged at that moment, it would have shot me through the front of the garage.
Last week I took it to the transmission specialty shop with the best reviews in town. As life would have it, he kept it three days, driving it four times, and it worked perfectly each time he drove it. Fluid looks fine (replaced at 120k miles) and fluid level is perfect. No codes stored in transmission computer.
I thought it was intermittently draining the torque converter until this last time when it failed after being shut off for only a couple of minutes.
The transmission guy is not interested in rebuilding the transmission even if I wanted to try it. He worries that because he does not know what is causing the problem.
View 3 Replies
A friend of mine has had this 2000 Sierra since new. It has just over 100K and never had any cooling issues before. Last week when it was about 10 below zero she drove it home and it overheated and pumped a couple quarts of antifreeze overboard.
She refilled it the next day and it was fine but got it looked at by a local independent mechanic. I had told her that it was likely a sticky thermostat and it ought to be changed out anyways due to its age. The mechanic thought I was wrong and that she had driven it off to quickly in the super cold weather.
View 2 Replies
The gear shift works fine, and we lifted the hood and saw that the mech. arm IS working when we shift. However, the van will not move into any gear. won't go forward, reverse, etc... it acts like it isn't shifting.
i was driving down the highway, and noticed it wasn't accelerating and stepped on the gas.. .and nothing. I stopped the van, put in park, turned it off. Started it again, and put in D and wouldn't go, just engine revved. then put in reverse and same thing... didn't move but engine revved.
View 3 Replies
I replaced the front hubs and bearings on my brothers 2002 Camry today. He drove less than a block and developed awful grinding noise and it won't move in reverse or drive. It rolls when I put it in park. I had to pull it back into my shop. Is it possible the inner CV came loose and i didn't realize it? It all seemed to go back together fine. The new CV axle nuts were quite tight and slow to put on with my impact gun.
What else could possible go kaput when I re & re hub/bearings? And what a long ugly job to replace those bearings. Don't even think about doing this without a good hydraulic press. Up to the point of getting knuckle off, it was easy job.
View 10 Replies
I just changed my oil in my mk4 jetta 1.8L and after draining the oil, changing filer, and adding new oil, the car will not move in drive or reverse. Once I give it gas it will move but that's at the higher rpms. I am almost positive I didn't remove the transmission oil but I am just not sure.
View 12 Replies
Here is what I have:
2009 Santa Fe 3.3L AWD
70k KMs / 43k Miles
Temp has been very cold, -20C / -4 F
Car starts up without any problems. Try to put car in Reverse and the shifter is very hard to move, if it moves at all. When I am able to get it into Reverse, I then try to put it in Drive and it does not "engage" the "D" and the car behaves like its in Neutral. Moving the shifter back to Park, Neutral, Drive is very difficult and sometimes it will not go into Park. The dash lights do not illuminate the selected P, R, N, D.
However, once the car is warmed up (no longer on C on the temperature gauge) I can with a little effort move the shifter freely (but more effort than it should take) and the car behaves normally. Gear shifts are smooth and in general it is operating normally.
The dash lights do illuminate the selected P, R, N, D. I've checked the Trans fluid level and it appears to be normal and was planning to change it this w-e but I'm no longer sure it will work. Even if it has never been changed.
Also note that I have recently changed a wheel/hub bearing due to a noise that sounds a lot like loud tires on a highway. The bearing change did not eliminate the noise and I assumed that I've changed the wrong one. The noise does not appear to be coming from the Trans, but I cant be 100% sure. The noise is speed related and occurs only after about 20KM/h 16MPH. Unsure if they are related..
View 3 Replies
I just did a motor swap on a 2003 with 3.5 auto tranny and awd. engine runs great and every thing is running fine. Only problem is that the trans will not create any power. With no drive shafts on it still wont move the splines. With that said the trans was driving/running great b4 the swap.
View 2 Replies
When I started my car and put it in reverse, it didn't move. It felt like my front, right wheel was in a divet or was being blocked somehow (intuitively it seemed like if I accelerated enough, it would eventually move, but since there was nothing physically stopping it - that I could see - I didn't want to break something by doing that). I tried putting it in drive and neutral and the same issue was still there. I put the car up on a jack and checked one wheel at a time - I could move each wheel completely around in both directions.
I could move the steering wheel all the way to the right and to the left. I tried turning off the 4-wheel drive and that didn't do anything. At this point I'm concerned it could be the transmission or the drive shaft, but I'm not sure what to look for in order to know if I need to get it towed to a shop (hoping I can avoid this) or if there's a simple test I can do, or a way to "reset" something if it may be locked. I haven't had anything happen to the car that would have been of concern.
View 2 Replies
