Sierra :: 1998 GMC With 5.7 Vortec Engine - Random No Start Condition
Jun 18, 2012
My Sierra has the 5.7 Vortec engine with 230,000 miles. Ever since I bought the truck at 208k I've been having a random No-Start condition... It can be cold, warm, or not ran for weeks. I've replaced the Fuel pump (just the pump, not the sender too), MAP sensor, ICM, TPS, and Camshaft position sensor. I'm still thinking its a fuel issue. I get 61 PSI at the test port when ignition is on, 55 when cranking, and 54 while running.
View 3 Replies
Advertisement
A friend of a friend has a 1990 Escort 1.9L automatic with a TBI setup. It has a random no-start condition that only seems to act up when its cold outside (below 20 F). I've only seen it act up once with minimal testing equipment, so I'm digging for answers.
The injector fires normally and flooring the pedal goes into clear-flood mode as it should. It has spark, but sounds out of time. It will attempt to fire unless the pedal is floored long enough to take fuel away. Starting fluid in addition to the fuel makes minimal difference, but results in intake backfires when you stop cranking. After a random amount of cranking, it will eventually fire and then the issue goes away completely.
Once it fired, I was able to shut it down and restart it indefinitely with no hesitation. While running, it shown no signs of being out of time, vacuum leaks, etc. I have very little experience with the EEC system, but friends suggest a TFI module. A weak or mistimed spark seems to be the cause, but I'd like a second opinion. I shook and moved every wire I could find and checked the TFI pins for corrosion - no change.
View 2 Replies
I am having a random hard start condition. it will happen once a week or with no rhyme or reason. It turns over real nice but does not start until the second or third trythe last time on third try i push accel pedal to floor and it started. This hasn't happen in a few day so I cant tell you if the accel pedal will always work.
View 9 Replies
1998 chevy vortec 350. replaced fuel pump(twice),fuel filter, blew air through the lines, replaced fuel pressure regulator. Getting correct voltage at pump. pump runs. still only get 30 lbs of pressure. Need 60. Thought I bought a defective pump took it back. Same result. Doesnt leak anywhere I can find. Pressure doesn't drop. Just plain don't get the 60 lbs it requires. New battery as well and new F.P. relay.
View 6 Replies
I have a 98 k1500 5.7 vortec. I was driving and the next thing I knew my truck lost power and would misfire at an idle but only when under a load (in drive with foot on brake). The last time something like this happened an injector came out of place. So that's where I started. I wound up changing the whole spider injectors and ALL the gaskets, upper and lower. I put everything back together and the problem was still there so basically I am back to square one.
I then pulled spark plug wires while running to see if I could isolate the misfire and found that I could pull all 4 wires on the passenger side without any difference in while it was running. So basically my truck is currently running on 4 cylinders and they all happen to be on the driver side. I checked my compression on the passenger side and all 4 cylinders have 180 psi so that rules out the head gasket being blown. I am getting 4 codes , 520, p1345, p0155 and p0161. I know that i have to get tge truck properly timed with a computer but i don't think that would cause my problem.
View 5 Replies
So I got a 98 GMC sierra and the ect sensor that is on it only had one wire running to it. Obviously the previous owner tried to make something work. I bought a new ect sensor and pigtail to rewire it but can't find the ground wire anywhere. Looking for a wiring diagram?
View 14 Replies
I recently had intake manifold gaskets replaced in my 98 gmc sierra 4x4 pickup 5.7 . The day I drove it home from the shop it ran fine, even day after but the next day I noticed it seem to idle a little rough and even at normal driving, sometimes seems worse than others. No service engine light has yet to come on. Could there be vacuum leak, trash in intake or bad wires and plugs. Plugs, wires, rotor button and distributor cap are only year and half old.
View 1 Replies
2006 f-150 with a 4.6L. Its got 175k on the clock and ran like a sewing machine despite little maintenance other than oil changes. Recently it started running like crap; no power and missing so he borrowed a scanner and it was giving multiple codes. Here's what we have done so far, not necessarily in this order :
1.Checked for vac leaks with carb cleaner (this can be tough as engine runs crappy and hard to detect minor changes in rpms while your under the hood) no leaks detected yet
2. Changed the plugs, all looked good except for one which was heavily fouled and the electrode ate away mostly, I wasnt there and he doesnt remember which one but have a suspicion, more on that in a min
3. Changed most of the COPs and checked them all with a spark tester, all are firing.
4.Cleaned the MAF sensor with MAF cleaner
5. Checked back pressure on the exhaust by removing an upstream o2 sensor and holding a plastic fitting hooked to a pressure gage long enough to get a reading, about 1 lb idling to maybe 2 max when engine is reved, gage is not the best and fluctuates a 1/2 lb or so. Exhaust does not smell of rotten eggs.
6. Changed the fuel filter, it was terrible
7. Ran a bottle of Seafoam in the tank
8. Took the throttle body and egr valve off and checked for carbon stoppage, the holes in the egr were not blocked
9. checked the PVC valve and line and both elbows
7. checked the injector connectors with a noid light for signal, they all flash, checked the injectors them selves with a multimeter set for ohms, all about from 13.5-14.5. This should mean they arent fried but could they still be stopped up? They all sound like they are pumping when you listen with a mechanics stethoscope
9. Changed all 4 o2 sensors as this had never been done anyway
10. Compression check on cylinders, all within 10% of each other at about 180 lbs. When we pulled the plugs they all looked good except for # 7 which was heavily fouled ( I suspect the same on the original plugs) and again with a bad electrode, the part coming out of the porcelin. Intrestingly, this was an autolite plug, the rest were motorcraft, I hoped this was somehow just a bad plug but no change with a new MC plug
11. Changed the injector on #7
The scanner reads lean condition on banks 1 and 2 and random misfires on #4 and # 7 still. Per a troubleshooting tip online, we sprayed some carb cleaner in a small vac line coming off the manifold to induce a rich condition and the scanner showed the o2 sensors go to .900 which is what they are supposed to do per the guide. This means they are functioning correctly and a bonafide lean condition exists. I am leaning towards a vacuum leak around the plastic manifold under the aluminum one, maybe the gaskets but would like to rule out the egr valve, could it be the culprit?
I have even considered the possibility that the PCM is bad, though not likely. I have read to detect a vac leak you can hook the scanner up and spray the carb cleaner around on the manifold and lines with the scanner hooked up watching the scanner PID for the o2 sensors and when they detect the cleaner, they will hit that .800-1.0 meaning the engine sucked the cleaner in and you have found your leak. The exhaust smells rich. If it is a vac leak, you would think it should be a massive leak and not hard to detect, as crappy as the truck runs. I have searched the forums for days and exhausted about all I know to do.
Most important note: early on I suspected low fuel pressure as a possibility; with no schrader valve on the fuel rail and no easy spot to T into the system, we were scratching our heads how were gonna measure psi but the scanner reads absolute fuel rail pressure, gives about 40-43 psi. I hope the scanner is telling us what we need to know there, would prefer a mechanical gauge on the rail!
View 2 Replies
I have a 1998 Maxima with 57K miles on it. I just bought it about a month ago. Anyway, a week ago I noticed It felt very "choppy" when I shifted into Drive or Reverse. It felt like it was going to stall but it never did. The Service Engine Soon light has been on for about 3 weeks but now, when I go up hills especially, that light blinks. I can still drive it but I shift into Neutral at stoplights to avoid hearing the rough idle while in Drive. Went to Pep Boys yesterday - they had the car for about an hour and then informed me that they would need to keep the car for a full day because of the "complex issues involved" - especially concerning the codes. The codes they read were:
p0300 random misfire
p0325 knock sensor
p0440 evap emission
My car passed smog test abut 3 months ago. I can drive it OK it just is very choppy and so there's not a lot of power, especially going up hills.
View 1 Replies
2004 GMC Sierra 2500 HD, 227,000 miles 6.0L V8.
While driving up hills or increasing load, the CEL will flash multiple times, I pull over as I know CEL flashing is not good. I turn the truck off, allow it to sit for a few minutes, whip out the code scanner, only code that was there happens to be P0300. Truck has poor MPGS, idles rough, loss of power. this happens every time I drive this vehicle as I use this truck to pull my trailer that weighs around 4000 lbs. Problems come and go. Some days I can drive the truck for an hour with no problems, come up to a red-light, BAM, CEL is flashing, truck is bouncing side to side due to the poor idle, other days this happens while sitting in the parking lot of my job with the ac on.
Truck has been to the shop several times as I'm no mechanic. Parts replaced are as follows:
- Fuel pump
- Throttle Body
- All plugs
- All wires-All Coils
- Intake Manifold Gasket-
- Battery
- Sensor 1 Bank 1 O2 Sensor
- Sensor 1 Bank 2 O2 sensor
View 9 Replies
I have a 2001 GMC Sierra with a starting problem: When you've driven it long enough for the engine to reach about 210 degrees, if you stop the truck it won't start back up until the engine has cooled down to about 200. It only does this when it's over 80 degrees outside, though.
View 5 Replies
I have a 1998 Accord, 4-cylinder VTEC standard transmission, 226,000 miles. Last fall I first experienced a problem with the car where within 5-10 minutes of starting the engine and driving, the engine seems to lose power/fuel and RPMs act as if they'll drop low enough for the engine to stall. If I take my foot off the accelerator, and reapply, the engine seems to gain power again.
Also, if I open the accelerator to full while the problem is occurring, it can occasionally "push through" and gain power again. Similar things will happen while stopped. In neutral, RPMs fall low and suddenly jump back up and then settle into normal idle. The problem never persists longer than 10 minutes within starting the car.
I took my car into a local shop that came recommended by a friend. They investigated a "check engine" light that didn't explain the problem and were never able to recreate the condition themselves. They replaced a few parts but lost the work order so I don't even know what they changed, but the problem seemed to have solved itself for a while. Recently it started up again and I would love to sort it out.
View 2 Replies
This engine will not start unless we dump gas into carburetor. Changed the fuel pump, fuel filter and fuel regulator. At the shraeder valve we are getting 20psi. I hear that it only needs to be at 10-12psi to run. What else is controlling fuel to being dumped into the engine!
View 3 Replies
I have a 1 ton 2000 GMC sierra (old body style 99') 7.4 liter V-8 Gasser with the Allison 1000 tranny, 4x4. the engine will not crank over..
Battery was dead so I charged it, battery was holding 9v, so i hooked up jumper cables to my new car, gauge showed 12v, so I tried to start the truck.. the fuel pump, antilock brake system, and gauges came on.. as well as the "check engine light", "service engine soon", and battery light... I ensured the trans was in park, even tried neutral.. no crank.
I hooked up the mini scanner tool I have, and got no codes.. cleared the ECU/ECM anyways.. no crank.
I also tried swapping out my starter relay with the A/C relay, and pulling fuses to the ECU/ECM for 20 seconds to clear any issues/codes.. no crank
My next option is to clean the battery cables & terminals (or replace the cables), and replace the battery... the battery is only 2 years old.. due for replacement, but I'm kinda broke right now. The battery is one of those stupid side terminal ones with poor connections to begin with.. is there a top post terminal battery I can get to replace this POC? or will the posts hit the hood?
This is a plow truck, single battery setup (at the moment).. and the fisher 8' plow when running the hydraulic pump severly drains the battery.. lights dim severely, been wondering about a higher rated alternator (factory is rated at 120-140amps), larger power cables... etc.. dual battery system...
View 4 Replies
I have a 98 gmc k 1500 350 5.7 . Was having an issue with the truck bucking it would die very briefly thought maybe bad gas. Added treatment and few days later it was doing the same this time back fire check engine lite came on checked code mass air and cam position sensor.
I pulled cap and when I was about to take rotor button out I noticed play I could actually push down on it. I pulled distributor and confirmed the play I replaced new complete distributor and yes I forgot to mark position so line tdc #1 compression stroke installed distributor timing was off.
But running rough so I re adjusted timing now it just cranks I have played with the timing alot so I tested the coil had some strange ohm readings ( high quality meter) and have voltage 12 vdc at coil and module replaced coil today still same thing I have fuel and 60 psi of fuel pressure and it holds with key off and it's not the pass lock security does not flash. Fuel pressure regulator can't be leaking.
View 5 Replies
I recenlty bought a 98 GMC sierra for a great price knowing it needed engine work. It has a constant misfire on cylinder one and it causes the whole truck to shake constantly no matter whether idle or acceleration or slowing down. At first I was thinking a burnt exhaust valve. I ran a compression check (the engine was cold though) and I heard a cold compression check means nothing. But in doing so I found that cylinder 1 has the highest compression out of all. I plan on another compression test tomorrow when engine is warm. But until then I was thinking maybe a bad injector on cylinder one? It is a "spider injection system" and I was wondering if it was possible for one injector to be clogged or not working and the rest be fine. I have seen where one will get hung up and cause hydrolock.
View 19 Replies
My 1998 GMC Sierra K1500 has developed an intermittent high speed miss. I doesn't miss while idling but with no apparent regularity it will jerk as though the engine lost power for just a moment. I just replaced the distributor cap and rotor and the plugs and plug wires appear to be fairly new (I bought the truck last May). The truck has about 213,000 miles on it.
View 6 Replies
2010 Santa Fe V6...about a week ago the starter started acting up. When you try to start the car, you would hear 3 clicks before the engine would start normally. The clicking is random and does not happen every time. The dealer could not find anything wrong other than the battery was reading 440CCA vs the 600CCA it was rated. Starter clicked first thing today on the way to local mechanic to get brakes replaced. They tested battery and it tested good. What could be the problem?
View 4 Replies
I own a 2006 Azera Limited. I've been experiencing intermittent problems starting it. It cranks fine but will not start? The battery is new.
View 1 Replies
Wants to crank. I notice when I turn the key switch on (not start) the gas gauge pegs out as if a super full tank and no fuel pump noise. At times, leading up to the crank but no start condition, I would turn the key on, hear the fuel pump and the gas gauge would indicate proper fuel level. When this happened, the vehicle ALWAYS started.
Here what I know now;
1. Fuel pump works. As indicated by the red auxellery jumper lead inside the engine well.
2. Good fuel pressure.
3. Starter checks good.
4. Battery hot and leads are cleaned.
5. Grounds in engine compartment and at fuel tank are cleaned.
6. Vehicle does have gas.
7. Air bag light stays on, even after pulling battery leads, letting set, and reinstalling.
This ABS light would come on and go off independently before the "crank but no start condition". So I'm assuming that the ABS might be its own problem; but not contributing to the crank but no start condition? There were problems leading up to the no start condition. Vehicle began to become hard to start (but would start). After starting (at idle) if the gas pedal was pressed aggressively, the "service engine" light would flash on and off rapidly and the "ABS" light would come on. At this point the vehicle wanted to die. No apparent codes were given.
Now the "crank but no start condition". Before this problem, the vehicle was sending the code for 3 o2 sensors. But a new fuel filter corrected this problem completely with no further apparent problems. Then (about 4 weeks later) the "crank but no start". I do not think the fuel filter and the "crank but no start" problems are related.? No other maintenance has been done to this vehicle that might cause this problem. At this point the manual I am using is useless...
View 14 Replies
2008 Chrysler Sebring V6 hardtop convertible ... Intermittent no crank / no start condition – when turning key to start position, either you get nothing as if there is no battery connected and or a slight click as if the solenoid was trying to engage. The pattern can be nothing, nothing, nothing, click, click, nothing, startup or any combination of clicks or nothing, always resulting with a startup. Sometimes it will only be 3-4 attempts, other times 15-20. This occurs anywhere from every 15-20 starts to driving 2,000 miles from NH to FL without one failure.Completely random occurrence – no pattern can be seen – has been ongoing since September 2015 to now March 2016.
I have tried moving the shift lever and the steering wheel while it occurs, no change.Facts – battery was replaced 2-3 years agoAfter the first occurrence I yanked the battery, cleaned the terminals as well as the terminals under the hood. Over the next couple of months brought it to the dealer who could find no codes and of course it did not fail while they had it so they did nothing. In December I appealed to the service manager to replace the starter as I thought is sounded like a bad spot on the armature. He did so and also had the WIN module replaced. No issues until I was in FL weeks later. Here the dealer has replaced the PTC and TIPM modules and installed a redundant ground wire. The problem is still occurring. I’m down to under 400 miles on my 100k bumper to bumper warranty?
View 9 Replies
