Sierra :: 1996 SL V6 - Rough Idle After Tune Up / Skipping When Accelerate
Dec 21, 2011
1996 GMC Sierra SL V6. Owned since new. 100,000 miles, never tuned up. I decided to get a tune up in hopes of increasing mpg, and it was overdue really. New plugs, wires, cap, rotor. Got truck back and it runs rough, knocking, skipping, hesitating, bogging down when trying to accelerate, rough idle. Went from 15.5 mpg, down to about 14 mpg. They said they put in all AC Delco parts. Brought it back to them twice now and they cannot figure out the problem. It ran PERFECTLY before I send it in for a tune up. No problems whatsoever.
View 2 Replies
Advertisement
I did a tune up on my 20th last week, plugs and coil packs and oil change. now i have a strange idle that it wasn't doing before. i checked all the plugs over again and they are gapped fine and i have no CE light on. Every now and then my RPM meter will jump down and then right back up, same with the boost meter at the same time. i had it looked at at the garage i go to and they said they cant seem to find anything wrong. What might be causing the rough idle? keep in mind this only started happening RIGHT after the tune up.
View 24 Replies
I have a 2000 Alero w/ 2.4 103,000 miles auto. I have been trying to fix a problem for about 3 months. It all started one night when i got stuck in my backyard in about a foot if mud. I thought i could drive it out, but when the wheels would spin and traction control would limit the rpms. After getting out the car would skip every now and then going up an incline at highway speeds in 4th gear (drive) then it would skip while idling. I could get it to run smooth if i hit the pedal and made it shift to 3rd. I drive this car daily and the problem has got worse slowly. Now its hard to crank and when it does there is a small amount of white smoke with strong gas smell while the motor spudders for about 10 secs.
It will finally "clear" up and still misfire every few secs or just cut off. Gas mileage is terrible between 15-18mpg. The engine light and trac off light has only been on twice. Both times the code was for random misfire of multiple cylinders. I have put plugs, boots (wires), distributor, 2 fuel processor regulator, seafoam, all octanes of gas, pulled injectors (looked ok a little dirty but still could be one) and I have ordered ignition control module. Its getting hard to drive and even harder to sell. It has just started the white smoke and gas smell and i think its that's the pressure regulator, but the skipping and rough idle....
View 8 Replies
I've got a '96 Sierra manual transmission with 215K that's been running fine. I just ran it 400 miles without a problem. Recently I downshifted into fourth to go up a hill and I had a sudden loss of power and a rough ride like I had a flat tire. The harder I press the gas the rougher the ride and it idles almost normally. The check engine light came on and blinks 12 times.
View 1 Replies
Replaced the spark plugs and wires a couple months ago. Started skipping yesterday throwing the #4 misfire code so I replaced the coil pack, reset the check engine light but it's since came back on and has a rough idle and loss of power. By the way, it's a 97 F150 4.6L 4x4 with 200,000 miles.
View 4 Replies
2000 Sierra 1500, 5.3L engine. When he starts it in the cold (below 40 degrees) at first hits 1000rpm, then immediately drops to 400-500rpm. The idle is rough and wants to die if he tries to drive it. However after 10-15 minutes and the eng warms up, its fine no problems at all. There is no codes, so the scanner we had didn't tell us anything. He had cleaned the TB and intake system with cleaner, no dice. He also disconnected the IAC while it was idling rough, that didn't change the way it ran at all. We would like to toubleshoot it more before we start throwing parts at it.
View 1 Replies
I have a 2000 Corolla with about 147,000 miles. At idle it runs very rough, but can accelerate up to about 50 mph. Then it starts to cough and wheeze and run roughly again and won't accelerate any further. It feels like the engine will shake itself off its mounts, so I slow down and stay under 50 mph. I replaced spark plugs and a repair place hooked it up to a computer. They then told me it needed about 1800 dollars worth of repairs to replace the valve cam I think they said. I'm skeptical and wonder if it just needs a tune up, . It has not had one since I bought it at 128,000 miles, and II don't know how long it had been prior to that.
View 5 Replies
My car has suddenly started stalling a lot. I can get it to start right up if I put the clutch to the floor and it will idle fine until I start coming up of the clutch even while it in neutral. At times it will idle in neutral then start to idle rough and stall. I can drive it in reverse but can't drive it forward except in first if i keep the clutch at a certain point and not release it all the way. However when I try other gears sometimes it's like it does't want to go stalls. What it might be?
View 1 Replies
1996 / 2.2 L4 / 186k / Upper engine rebuild 30k ago
Car was driven on a errand by my mother. Upon trying to leave for home, the car started running very rough, and stalling. From the description she gave on the phone, it sounded like a plugged up exhaust. I told her to get some fresh gas and ease it home after.
When I checked the car for codes, I got 2. A P0300 and a P0122. Okay, so the throttle position switch has taken a dump, that's easy enough. The car has 186k miles, but my constant nannying usually soothes her, so surely that's all, right? God, I wish that turned out to be true.
I pulled the plugs, and #4 was gas fouled and sooty, #2 and #3 looked lean, and #1 was partially wet fouled. There was also gasoline in the oil. When the car would run, it would run the gambit from idling semi rough then stalling out and refusing to restart, almost like it was flooded, to idling scarily bad and no pedal response, to running too high of an idle and idle searching.
Since I have:
Replaced the TPS
Replaced the IAC
Replaced the CTS
Replaced the MAP
Replaced the ICM
Replaced the FPR
Replaced both ignition coils
Replaced plugs and wires
Replaced the fuel injectors
Replaced the PCV
Replaced the fuel filter
Checked the pintle on the EGR (looked good, cleaned)
Checked for Vacuum leaks (as best I could)
Checked the Fuel pressure (40 PSI) (drops to 20 after shutoff)
Checked for exhaust restriction (ran open exhaust manifold)
That brings us to today. New injectors just in, and the engine will run, but rough and loud. It almost sounds like the firing order is off slightly (I am using 1342 or from L to R 4132) and throttle control is almost non existent. It also shuts off when its warm almost like its flooded. No codes are showing. (despite discovering a sensor in back being unplugged and the O2 sensor being unplugged at times).
View 19 Replies
I own a 1996 Buick Regal with 132k miles on it, 3.1L six cylinder. The other day I was doing some general maintenance and noticed that the exhaust smelled like sulfur (rotten eggs). Now, I am loosely familiar with the causes of such a thing but not well enough to diagnose it properly the first time. The car has been idling rough since I got it (almost a year ago now), I have a feeling that it could be the O2 sensor causing the rough idle and the sulfur smell but I am not completely sure. I should have one of those fancy three-part injector cleaners done?
View 6 Replies
I have a 95 Buick Regal, V6 3.8 Liter. The symptoms are the following: stuttering idle. And lack of response at times when I try to accelerate. Like sometimes I'll be driving on the highway, and having no problems. Then I'll be going up a hill at around 55 mph, and then the car will shudder as I try to maintain a speed of 55 mph. So I have to ease off the accelerator and slow down. At first I thought this was a transmission problem, but I am guessing it's the same problem that causes my choppy idle.
So I had this acceleration problem on the highway when I was going up a hill. And a weak idle. These problems have been going on for several months now. They were annoying, but didn't seem that serious. Then all of a sudden, on a rainy day, the car was really responding poorly to acceleration at all speeds. I was able to drive around, but I couldn't count on the car responding right away when I hit the gas pedal. And the car would shudder at times. Then, I didn't drive the car for a few days, and then it was dry, no rain, and the car ran better. So I am thinking humidity makes the problem worse.
I have also noticed over the past few months, that the car runs best when I start it up after a few days of not running it. Then if I drive the car a few miles and let it sit for about 2 hours or so, it would idle weakly when I would start it up again. The car's been doing that for several months now, but it wasn't really affecting the drivability or the response of the car when I hit the gas pedal.
Now it's gotten much worse. So, I've already replaced the following items myself to no avail: mass air flow sensor, oxygen sensor, and egr valve. I am guessing the next thing to fix is the pcv valve. But I also think it might be the fuel pump. My first guess though is the pcv valve. What else could it be? And is there any easy way to test to see if the fuel pump is going bad? Or should I just take out the pcv valve and see if it looks bad?
View 14 Replies
I have a 96 Mazda Protege DX. 1.5L engine, now with 161,000 miles. 5 speed manual transmission. I had it for 7 years. Originally bought it for $1900 with 121,000 miles.
This has been a problem for about 5 years. When I am at a red light or idling and I step on the brake, my idle gets rough and my engine feels like it is about to turn off. The idle does not bounce up and down. It just goes down to 400-500rpm from the normal 800-950rpm range.
Again, this only happens when I step on the brake while the car is not moving. It does not seem to happen when I coast in neutral and hit the brake to slow down. I raised the idle a bit, but it still does it. I could not find any vacuum leak around the brake booster and I know the brake booster works because I pumped my brakes while the car was off, and when I turn the car on, the brakes soften up.
Also, my brakes feel weak. I usually hit the brakes nearly to the floor board to stop the car. New pads, rotors are good. Brake fluid is at right level. Mechanics say nothing is wrong with my brakes.
Secondly, my belts screech at every start up. Lasts anywhere from 3-20 seconds. This has been happening for the entire 7 years I have owned the car. Mechanics replaced the serpentine belts twice in that time. Replaced a pulley and A/C compressor. I tried using WD40 but it doesn't effect it. Mechanics tell me that the belt tension is correct and they do not know why it still screeches.
View 6 Replies
My 1996 S10 2.2 liter pickup has been having some 'issues'. Truck has been kind to me over the years, but now is running a bit rough. It has an irreguler idle and continues to run this way through all speeds. The blinking code reads "cylinder 1 misfire". I did all the basics. I changed the plugs and wires, ignition coils and fuel filter. Here is where is gets tricky, after changing the fuel filter, it ran great again. Then it started to run rough again later that day. I thought I somehow clogged up the new filter, so I removed the new one for inspection. Realizing there was nothing wrong with it, I reinstalled. Truck ran great again. Went out to drive it to work a couple hours later and it started fine, then after about 10 seconds of running, it went back to the rough idle.
View 19 Replies
I towed my 32 ft/ 600lb travel trailer 115 miles into arkansas today. When I arrived at the campground, the engine was running rough and shaking the vehicle. I saw highs of 175 (trans temp) 1150 (EGT), 214 (ECT), and 224 (EOT).
I recently installed the canned trans tune from my new SCT X4.
I pulled codes (none), checked cylinder misfire count on scangauge 2 (none). In fact, all gauges on the SG2 were within spec. I popped the hood and let it idle for 15 mins. Temps all dropped down to what I usually see after normal driving (not towing).
The engine did start to calm down as it cooled, but still sounded a rough
View 14 Replies
I have a 96' 1500ec with 5.7L and auto trans. I have been fighting an ongoing code of multiple misc. cyl. misfire. I noticed a hesitation only when I start out in first gear, once it shifts or if I start out in second it's smooth. I have 138,000 on the odometer. Code-0300 with the mmcm , how about timing, distributor or stretched timing chain?
View 2 Replies
I went out to my 96 gmc k1500 this morning after auto-starting about 10 minutes before to let a/c cool the cab. It was running fine but when I got in I noticed the battery light was on and the electrical gauge was topped out past 19 into the orange. I turned the key into the "on" position and when I hit the brake pedal to put it into gear the engine started surging and then dieing down, back and forth (approx. between 500 and 1500 rpm) until it just finally died (lasted about 20-40 sec.). Ignition was still in "on" position but the electrical gauge returned to normal.
Tried starting it again and electrical gauge jumped right back up and battery light was still on but the engine didn't start surging again until I hit the brake pedal just like before. I'm going to guess my alternator/voltage regulator needs to be replaced but beyond that what else it could be. I'm not a mechanic by any means but I've managed to make minor repairs over the years myself following the Chiltons or Haynes manuals. I have a Hanyes manual for this vehicle but the troubleshooting section doesn't cover my problem specifically.
View 3 Replies
I built the 400 in my 79 a couple years ago and it runs very well...until yesterday. I'm about 80 miles into this tank, and on my way home from work, I thought I felt a vibration (not in the steering wheel, but in the front oc the truck). Then the engine became evident it was running rough and was skipping and surging. I stopped.
It idled pretty rough, then died. Fired right back up, ran rough, and died. Sometimes it would idle smooth for several seconds (20-30) then start surging and skipping and die. I could hold a little throttle and it would run about the same, except some backfiring in the exhaust (more like a big hiccup).
The carb is a 670 Street Avenger with nothing really done to it. The bores are really black (not sooty, more damp or so). I have always used the air filter, so that's odd. I took the carb off and removed the bowls. Nothing inside has a dirty or clogged appearance at all. Not sure if I should completely rebuild it.
View 6 Replies
I just completed a successful second spark plug change, using Motorcraft SP515 plugs just like last time. After reconnecting battery and starting engine, it ran poorly throughout a short road test. Felt like it was skipping. Checked under the hood and found that the #2 fuel injector was disconnected, so I reconnected the injector.
I took another short road trip and it still ran poorly as if skipping. So, this time I disconnected the battery for several minutes while removing the #2 plug thinking I may possibly have fouled the plug by the injector not being connected. I also checked all of the other injector and coil connections. Reconnected battery and took another short trip. It still runs poorly. No codes yet.
View 14 Replies
Our 2007 Avalon with 65xxx miles on it was skipping and running rough this morning. Running a scan with my VAG-COM gave me these codes.
Mode 07: Pending emission related fault codes Address 7E8: 2 Faults Found: P0305 - Cylinder 5: Misfire Detected P0355 - Ignition Control Circuit for Cylinder 5: Malfunction
Would you say it is time to replace the Coil for this cylinder, or should I do more troubleshooting first?
From what I've read on this forum, it appears cylinders 1, 3 & 5 are at the rear of the engine and are a PITA to change. Is there a good write-up or video on how to change these at the rear of the engine?
View 2 Replies
I have a 1995 GMC that I have owned since new. It has 212,000 miles on it, a 305 TBI, and a manual five speed. It started running bad all at once. It idles rough, at different speeds and never settles down, (between 900 and 1300 rpm. It smells like raw gas, smokes, and has no power to get started from a stop. I checked the vacuum, it is at 19" at all rpms. The MAP sensor reads 0.3VDC when off, 4.12VDC when idling, and 1.5VDC at WOT. It appears to have 12PSI fuel pressure (after a messy test set up!) on the fuel pump side of the fuel filter (filter replaced 10,000 miles ago). The EGR valve appears to cycle OK when I suck on the vacuum line so I assume it works OK. I found a bad TBI flange gasket and replaced it. It runs slightly better but still smells like raw gas and has no power. When I try to accelerate, it immediately has no power, like a big vacuum leak. The idle is close to normal (900rpm = normal). Do I just start replacing parts?
View 9 Replies
just bought a 01 f350 v10, 40,000 miles, plowing beast, anyways when taking off truck seems sluggish, give it more gas as its fine. At idle there appears to be a skip. There are no check engine lights on, could it be the coil pack or even maybe fuel problem? Have done plenty to this beast to get it close to perfect and this motor issue is it.
View 14 Replies
