Saturn - Sl :: Coolant Leak After Replacing Belt Tensioner Assembly
Nov 15, 2013
We have a 97 Saturn SL2. The belt tensioner assembly cracked and after the guy replaced it, immediately upon driving, the low coolant light starts flashing.
Drove it this way a few times while keeping an eye on coolant level. Parked car for a few days, then notice a big puddle of green coolant under car. It has been sitting now for several weeks.
Could increased tension from the new tensioner pulley cause the water pump to die?
The car has never overheated, though. If water pump was toast wouldn't it overheat?
View 3 Replies
Advertisement
I got a warning light that the Toyota dealer said indicated that the Coolant Storage Assembly tank had gone bad. It's not leaking, just not working. It's a very expensive fix and in the little bit of research I've done I'm wondering whether it needs to be fixed. My understanding is that it takes warm coolant and stores it in a thermos-like container to stay warm a few days to assist cold starts. However, I live near San Francisco and the weather is very mild here. We might have a few below freezing days in the winter, but for the majority of the year nights are only 50 degrees, and usually only 40 degrees n the winter. So, do I really need this fixed? It seems that since the weather here is so mild it should be fine. BTW, I haven't fixed it since the light went on in January and haven't had any problems starting the car so far.
View 2 Replies
1996 Buick LeSabre 3.8L... Under the pcv valve housing is a short plastic 90 deg. elbow, about 3/4inch wide. The elbow looks like it comes from the upper plenum and goes into a metal housing behind the belt tensioner. This elbow leaks from behind the belt tensioner side. My question: what is this elbow called? How do I fix it?
View 3 Replies
I replaced a timing belt and related parts on a v 6 atq motor and three weeks later there's a pretty good oil leak, where its from or if oil leak can be related to timing belt replacement... leak seems to be in same area as crank pulley but not sure...
View 2 Replies
2006 6.0l ... I've read all over for tips on routing this belt and everyone plays it off as being some simple '20-minute' task. I'm on my 4th hour on this now.
I can't figure out how to route the belt around the tensioner pulley, circled in the picture (from another thread). Everyone glosses over how to do this and I can't figure it out.
It seems like the only way to get it on is to bend the belt and slide it between the pulley and the block, but that I just can't reach the blasted thing.
View 4 Replies
My 2009 Vue developed a coolant leak into the oil at 130k km. I had to have replaced. GM has a technical note about this exact problem with the recommended fix: Engine Replacement. The coolant was leaking into the oil at the water pump.
The Statement from the dealership states that there was a crack in the block near the water pump. The dealership was good but a block should not break like this. Is this a design defect with the block, and if so is their a class action already started?
View 1 Replies
I was driving my 2005 RX 330 (138k miles) North on I-75 through Atlanta in rush hour traffic when the car completely died in the left hand lane w/ no shoulder. GDOT stopped six lanes of traffic to push us up and over a couple of hundred yards to a right shoulder. It was determined that due to a coolant leak from the water pump the timing belt malfunctioned and shredded.
I had heard that the water pump should be replaced during the 90k maintenance when the timing belt is changed, but my water pump was not replaced according to my maintenance records. I understand from reading a couple of posts that this isn't always required but that they do check the water pump. Is this correct? And if so should they have noticed that there was a potential problem?
View 9 Replies
I replaced the belt tensioner. Today, after much prodding, I noticed the tensioner is rattling which is weird considering is only a year and some months old. The question is what can cause the tensioner to rattle? The belt is fine, is not cracked and it sits fine on the pulleys.
View 4 Replies
I needed to tighten the belt tensioner up, but couldn't find a DIY. So reaching out to see if this is normal? If not how do I tighten it up?
Here lately the car has been idling funny, kinda sounds like it has a cam or something, once I accelerate it smooths out fine. I thought it was a loose clamp on my intake to the turbo but once I got that clamped down correctly it still was idling this way.
View 2 Replies
My serp belt started squealing so I pulled the thermostat housing to inspect the rubber gasket. It looked OK, but I cleaned up both surfaces and replaced with a new gasket, and put it back together. The housing was replaced just a couple months ago along with new hoses. It was not corroded and OK to reuse.
Started the truck up and saw a slowish/steady drip of red Cat ELC dripping on the driveway. Opened the hood up again and carefully inspected around the thermostat housing - no coolant is leaking there.
I did notice the same slow/steady drip coming from just behind and beneath the thermostat housing. See in pic, this is where it is dripping. One other question, what is this plug for on the side of the water pump?
View 14 Replies
First off I have a issue the Timing Belt Tensioner Stud / bolt that holds my tensioner on is stripped and came out with my tensioner. I don't want to risk putting it back into the engine because some one prior to owning my car stripped the nut that holds it in. Where I could get a new one of these bolts. I have a 2000 VW Golf GL with a 2.0l. I've searched high and low on parts sites and cannot figure out where to buy this item.
View 3 Replies
I've replaced the serpentine belt on a 06 Pontiac G6 (6cyl) and I noticed at idle the tensioner has a slight bounce to it... Is that normal? It goes away when you hit the gas. Apparently the tensioner was replaced less than a year ago
I attached a short video. [URL] ....
View 2 Replies
During the 120000km (75000mi) service my Toyota local service said I have a noisy Prius and that the sound is from the belt tensioner bearing.
As I bought it used and always heard the same sound. I've made a video ....
View 4 Replies
How to replace the belt tensioner. It's not putting out enough tension when the engine is cold. So, the belt makes chirping noise for couple of minutes idling when cold with AC on.
I had the AC inspected and everything checks out according to my mechanic.
He believes that the issue is with the tensioner since I had recently had replaced the serpentine belt.
View 6 Replies
I own a 2008 santa fe SE, the belt tensioner start to making noise recently, just wonder if it's covered under the warranty so I don't have to pay out-of-pocket to get it fixed. This car have 68000 miles so far.
View 19 Replies
I am deep into replacing the timing belt on my 08 Elantra 2.0, and am nervous about taking the tensioner off since it is not obvious how to set it. I could use a fool proof explanation on how to set the tensioner.
The Haynes manual talks about 1/4 deflection but that seems too imprecise.
I can not see the marks in the video : DIY 2008 Elantra timing belt video 2 of 2 - YouTube
And this post 2008 Elantra Timing Belt does not quite seem to explain. I am contemplating putting it all back together, just changing the accessory belts and handing it to a shop. I could use a fool proof explanation on how to set the tensioner.
View 7 Replies
I had my timing chain tensioner replaced. When they do this do they touch the serpentine belt tensioner? 1000 miles after the timing replaced, my serpentine belt shredded and they say I need a new serpentine belt tensioner. Does this sound correct?
View 3 Replies
I have a 2008 F-150 with a 4.6. I have a sequel and I believe it is the belt tensioner pulley and / or the idler pulley above it. Looking for proper procedure to change one or both. It is pretty tight in there. How much stuff do I have to remove to get in there. Should I replace both pulleys at the same time.
View 2 Replies
So car not turning over after replacing (right side) headlight assembly. Was turning over prior. Replaced the battery, same result.
View 4 Replies
I've got an 06 XLT 4x4 with the 4.6L. I'm replacing the wheel Hub bearing assembly this evening and got the old one removed. Opened the new on to find no grease! I was shocked considering I just replaced the IWE and they come pre-greased. I plan on adding some grease around the hub gear but wondered if i should some how get grease in on that inner needle bearing? I have to have this put back together in a couple of hours so I can drive to work tomorrow.
View 6 Replies
After finally identifying a bad serpentine belt tensioner for being the the culprit for my engine noises, my mechanic said that the 'thru-bolt' is siezed. Since the replacement job was at my budget limit he said he doesnt want to get into it in fear that he has to brake the bolt and drill it out (requiring 2-3x more labor cost according to him).
If this is the case, and the 'thru-bolt' is seized, is this in any way something I can make a an effort to tackle? I have a jack and jack stands, and plenty of time.
View 3 Replies
