Santa Fe (CM - 2007-12) :: High Mounted Stop Light Bulb Replacement
Dec 31, 2015
I need locating the locking clips that hold the high mounted stop light assembly in place. Are there any diagrams?
View 6 RepliesI need locating the locking clips that hold the high mounted stop light assembly in place. Are there any diagrams?
View 6 RepliesHow to replace the bulbs of the rear high mount stop lamp on a 2009 Santa Fe?
I got the bulbs already, located the 2 nuts on the inside directly behind the brake light, but when I remove them, the assembly won't pop out.
I know the manual says they recommend getting these particular bulbs replaced at an authorized Hyundai dealer, but since I already bought the bulbs, I'd like to try and do it myself if at all possible.
I have a blown LED on a 2007 LS460. Bought a set of the Stop Lamp and started to embark on my little DIY today.
Both side covers are held on by a little plastic hook underneath near the row of LED bulbs. Hence, you will have to press down firmly to unhook and slide the cover towards you and lift it up to remove. (watch my youtube link below).
The center piece is held on by 2 screws (nearer to the row of LEDs) and 2 plastic clips (nearer to the C-pillars). Remove the 2 thumb screws and the plastic clips (twist or turn them 90 degrees and they should come off easily). At this point, remember to unhook the plastic connector.
Replace the center Stop Lamp piece and install everything in reverse order.
2008 Santa Fe. Removed 2 bolts and 1 nut as shown in manual. cleared the clip at the bottom outboard corner. What else am I missing? I'm still Unable to remove the headlight bucket. It will only come out about an inch or so then feels like something else is holding on.
View 8 RepliesAfter losing 4 bulbs trying to put the new light in from the bottom on my 07 Sonata's high brake light, I finally figured out, that if you take a dremel or other small cutting tool and cut of the tab on the bulb socket, the whole assembly will slide back into place from the top. Cut the tab even with the holes where the two wires go into the socket, and you should have no problems.
View 23 RepliesJust had new tires mounted and balanced on my 2011 Santa Fe. I purchased Toyo Celsius tires. I purchased the tires on line and had Faulkner Hyundai in Harrisburg PA mount and balance them.
When I drove to work 2 days later, I found that the vehicle starts to vibrate above 65 mph. When I get to 80 mph (typical traffic speed on I83 in the morning), the vehicle vibrates so badly that I shake in my seat.
This shaking leads to a feeling of lack of control. I'm hoping the dealer just screwed up balancing the wheels. Faulkner Hyundai uses a road force balancing machine.
My old near bald tires (the factory original Bridgestones) had a tiny vibration around 65 that went away as speed increased. With the new tires, the faster you go, the worse the shaking gets.
My 2011 Santa Fe still has under 30,000 miles on it!
My high mounted rear stop light and driver side real stop/tail light seems to be burned out. After checking manual, I found nothing mentioned about replacing 'high mounted rear stop light' at all. It's weird enough. From hmaservice.com, I found how to replace bulb, but, still could not find how to open that light box or package. And referring to 2005 model of Sonata, it says there are two nuts to be unscrew to open light box. However, I'm trying to find those nuts in my 06 Sonata.
View 89 RepliesYesterday i noticed that the right rear brake light and high mounted brake light does not work when i press brake only the left one work, although the right tail light work well when parking light is turned on. Is it a matter of fuse or wiring cut.
View 6 RepliesRecently I noticed that three LEDs in my 05 SantaFe's high mount stop light glow even without the brake applied. When the brake pedal is depressed, the entire light glows as it should. But only the three LEDs glow at all times.
View 13 RepliesI own a 2007 Camry LE and one bulb behind the temperature dial is burned out. It is the bulb for the indicator on the outside edge of the dial. I am curious how to remove the panel and rotary dial to access and replace the bulb. I've searched the forums but cannot find a description with pictures (hope I didn't miss it somewhere).
View 6 RepliesOne of the small bulbs in the corner of the headlight assembly is burned out. does any one know how to replace it?
View 1 RepliesI have a santa fe from the year 2008 and recently i had a trip where i would get tons of white smoke every time the car was at idle at the stop light. upon inspection, i saw that the coolant level was below the low line so i had it topped up and the problem disappeared. Everything was fine until today when the problem occurred so i checked the coolant level on the side of the road but the coolant level was fine and still is upon inspection when the car was cooled off. After i stopped to check the coolant level and restarting the car, the smoke was gone and did not appear again. I checked the internet for solutions and some suggest blown head gasket but many of the symptoms do not make sense in my case since the engine never overheats and the coolant level hasn't gone down in the past week.
View 3 RepliesI have searched everywhere, but I can't find the information I need for anything newer than 2007. I have the instrument cluster removed, and I can't figure out how to get to the bulb. In previous years, it just twisted out, but this one is different.
View 7 RepliesI can't seem to find a DIY on our generation RX to replace the fog light bulbs.
How did you do it? Under the front bumper, or pulling back the wheel well covers?
How to replace the fog light bulbs? I have a 2016 and would like to install LED bulbs.
View 3 RepliesWhile I was replacing courtesy light bulb, i got VSC light in my 2010 Prius. It doesn't go off. What can be the reason?
View 6 RepliesI have really taken care of this 2011 SF Limited with the 3.5 V6 but it has always seemed to idle rough at a red light/stop sign while in drive. Is this common for all the 3.5 V6 engines? I run a fuel cleaner through it before every syn oil change and also use top tier gas. It drives nice but like I said, at a stop in drive it seems to run rough at around 500-550 rpm's.
View 10 RepliesHow to easily remove the old one to install new bulb?
View 11 Replies Lexus IS: How to Replace Your Tail Light Assembly
Step by step instructions for do-it-yourself repairs
Browse all: Lexus IS Lighting Guides
My wife has a 2012 Avalon Limited. I also see that it comes with a side marker light as well. What is the bulb for the side marker light and how to replace it as well.
View 3 RepliesI was wondering, what the replacement bulb for the reverse light on the 2014 is250 f sport was..
View 1 Replies