Santa Fe (CM - 2007-12) :: Hazard / Turn Signals On Randomly When Vehicle Off
Jun 1, 2015
I have had an ongoing issue with my 2010 Santa Fe Limited with the battery randomly being drawn down and would not start the vehicle.
I saw a post somewhere on the internet to remove the Negative connection on the fender and grind it down to the bare metal so that it has a good ground connection.
I have done that last week, but last night before turning in for the night i looked out the window and saw lights in my driveway. I went out to investigate and found that the Santa Fe's turn signal/hazard lights were all on front and back and not flashing.
I got in the vehicle and turned the lights on and off with no keys and they all went out.
I got the schematics for the Santa Fe and i believe it could be the Hazard relay that seems to be located inside the I/P Junction box or could be the Hazard Relay Control in the BCM.
View 1 Replies
Advertisement
I just bought a 98 passat sedan v6 four days ago. When I purchased it the turn signals and hazards were working. I was driving yesterday and they went out all of the sudden. Thought it was the fuse at first, changed it, still not working. I bought a turn signal flasher relay, but the repair manual doesn't tell me which one it is so I can change it.
View 2 Replies
I just found a nice Prius C for sale with little damage to the front right corner, no frame damage or anything, just some bodywork needed. So, after it was fixed up. I brought the car back and there is weird issue that I have - turn signals and Hazard lights dont work. When I turn it on, i can hear clicks from it, but I dont see lights blinking on the dashboard and my head/tail lights dont blink as well.
View 5 Replies
Recently my Infiniti G20's turn signals and hazard lights stopped working. I replaced the flasher relay and turn signal switch but it did not solve the problem. Here is the kicker or clue. The lights flash when locking or unlocking the car with the remote FOB.
View 7 Replies
Car is 2000 Corolla with 58k miles. Today, I had my hazard signals on while parked when suddenly....they stopped blinking. The signal lights in the dash just stay on...they do not blink. I also verified that both front and rear lights also turns on...it just doesn't blink.
The corolla has a fuse box under the hood in the drivers side. Here is the schematic for the fusebox: [URL] .....
From what little I know about mechanics/electricity, can I just pull the wiper fuse and put it into the turn signal fuse while I wait for a new fuse? Do I need to disconnect the battery?
How to confirm this is the part I'm suppose to install: [URL] ....
View 5 Replies
I have checked the fuses for the Hazard and the Turn Signals. Both look fine. I tried replacing the turn signal flasher (which was a task in itself). After all of this it is still not working. What else could it be? Simple short?
View 2 Replies
I have a 2006 F250 Superduty 4x4 that the brake lights hazards and turn signals have stopped working in the rear.. The middle cab brake light does not work either.. The running lights do work as well as the turn signal and all lights in the front.. I also checked the trailer plugs and both work for running brake and signal lights.. I have checked all fuses under the hood as well under the dash with a test light and i have nothing blown.. I have replaced the Brake switch as well as the flasher module under the dash and picked up a new multifunction switch (Turn signal/hazard) and that didn't work either.. I'm stumped at this point.. I have not checked the bulbs yet but wouldn't think they would all blow at the same time.. (will do this next)..
View 3 Replies
My 2007 F150's turn signals and hazard lights quit working. I checked the fuse and it was blown. Once I pulled the old fuse out the truck wouldn't start at all. What happened?
View 3 Replies
I was adding some more running lights today and tried to tie in to the front running/turn signal light. Next thing I know I hear a pop and now no turn signals, hazards or brake lights on my 99 F250 SD V10. My 3rd (center) brake light does work though when I press the brake, it's just the tail brake lights that dont work.
I can't find a blown fuse for the turn signals or brake lights (not really sure which fuse box it's in since the manual doesn't tell me what fuse is what)
I however did find what I'm guessing are the flashers behind the radio. What might have went wrong where before I start dumping money in to flashers and relays.
The next question is, can I jump in to the marker/turn signals and add another single LED light to them off the front? If I can which color wire does what?
View 9 Replies
Recently, I lost function of brake lights, turn signals, and hazard flashers. All happened at the same time. Some threads discuss flasher relays, short steering column wiring (position of steering wheel), and fuse failures.
I checked #18 fuse and a few others. All had continuity. I assumed my bulbs were all good. My hazard push-pull switch did not feel right. There didn't seem to be engagement. At this point, there was a good chance that the multi-function column switch had failed so I decided to try replacing it. I'm happy to report that this switch was the cause of all the light function failures and now, all is well again.
Removal is done by prying the key lock switch cover off,, removing three 1" Philips head screws that attach the lower column shield to the upper shield. At that point the upper shield can be completely removed. The lower shield was not totally removed because the tilt lever was left on. The switch is attached to the column with two 3/4" Torx 20 fasteners. The upper is easily accessible and the lower fastener can be removed by pulling the lower column shield down so access can be achieved. The two wiring harnesses have a conventional harness lock to depress and the connectors pull outward from the switch. Installation is the reverse of removal, noting the dowel locator and small plastic dowel on the lower shield.
View 1 Replies
So after a pretty harsh storm last night I was driving today and my wipers came on. Went to turn them off and nothing. My headlights and turn signals won't work either. When I pull the stalk to turn my high beams on my wipers go off. Parked the car and the dash lights stay on without my key and the wipers randomly go on and off. The blinkers in the rear remain lit with the car off as well. At work right now so nothing came up when I searched briefly but do any of you have any insight as to why my car is possessed? Going to check grounds when I get home.
View 4 Replies
I have a 2001 Econoline and the turn signals work in the morning but when the vehicle warms up they stop working. I have replaced the bulbs and the fuses. What I could try next.
View 4 Replies
My service advancetrac light comes on about once a month, seems random but when it does the turn signals will not work, you have to hold indicator in place for signals to work-not to safe. My local dealer has not been able to fix issue...
View 3 Replies
Checked bulbs and fuses: not blown.... Is there a recall?
View 3 Replies
I have a chevrolet optra 2007 and the hazard lights won't work unless the turn signal (left or right) is switched on at the same time. Turn signals work perfectly fine.
View 7 Replies
I own a 2004 hyundai santa fe and just recently my turn signals have stopped working. My bulbs are fine because they still light up when I lock my car and my hazards work too. The flashing arrows on my dashboard wont show up for my turn signals but they will show up for hazards. I checked the fuse and its completely fine. I am so confused with what is wrong. The only thing I was doing before was messing with my new head unit which involved unplugging a lot of the stereo and fog lights and hazards but that all should have no affect on my turn signals.
View 6 Replies
Upgrading my side mirrors. When I bought my Santa Fe I completely forgot about these. I have tried google them but nothing comes up. I don't mind doing the install myself. I would even buy OEM parts as I assume its probably just plug and play with the old ones.
View 2 Replies
I just changed the whole bulb set (front and back) to LED and now my turn signals are hyper flashing. I read about the additional resistors but I doubt there is any space, whether in the front nor in the back, to place this resistors. Now, I understand that changing the Flasher is not an option on the 2014 DM model.
View 3 Replies
So I lent my santa fe to a buddy to do some hauling, I got it back yesterday and the turn signals and the brake lights don't work...notta. Regular running lights are working without issue, but no turn signals, no hazards, no brakes. Even the "tick, tick, tick" of the turn signal is gone, it's just dead.
View 1 Replies
My 2004 Santa Fe seems to be leaking oil only when I turn on the vehicle. I don't see any oil under the vehicle, however, I see white smoke coming out mostly from under the vehicle on the passenger side and I can smell the oil inside the cabin. I haven't experienced any power loss. How to better diagnose the problem?
View 1 Replies
The hazard lights (4 ways) have a mind of their own and will randomly flash once and then few minutes later it'll flash again.
I've checked the dash switch, did a quick clean with electrical contact cleaner, that's working fine.
View 4 Replies
