Santa Fe (CM - 2007-12) :: Gear Shifter Very Difficult To Move When Put Car In Reverse
Feb 25, 2015
Here is what I have:
2009 Santa Fe 3.3L AWD
70k KMs / 43k Miles
Temp has been very cold, -20C / -4 F
Car starts up without any problems. Try to put car in Reverse and the shifter is very hard to move, if it moves at all. When I am able to get it into Reverse, I then try to put it in Drive and it does not "engage" the "D" and the car behaves like its in Neutral. Moving the shifter back to Park, Neutral, Drive is very difficult and sometimes it will not go into Park. The dash lights do not illuminate the selected P, R, N, D.
However, once the car is warmed up (no longer on C on the temperature gauge) I can with a little effort move the shifter freely (but more effort than it should take) and the car behaves normally. Gear shifts are smooth and in general it is operating normally.
The dash lights do illuminate the selected P, R, N, D. I've checked the Trans fluid level and it appears to be normal and was planning to change it this w-e but I'm no longer sure it will work. Even if it has never been changed.
Also note that I have recently changed a wheel/hub bearing due to a noise that sounds a lot like loud tires on a highway. The bearing change did not eliminate the noise and I assumed that I've changed the wrong one. The noise does not appear to be coming from the Trans, but I cant be 100% sure. The noise is speed related and occurs only after about 20KM/h 16MPH. Unsure if they are related..
View 3 Replies
Advertisement
Got in to go to work this am, and the gear shifter was difficult to move. What to check?
I drove 70 miles to work and didn't seem like any issues with the transmission shifting.
Got in to go to lunch and it seems even more difficult to move...
Shifting back and forth in the selector seems to loosen things up a little.
A friend move the selector while I looked at the linkage and the bracket that support the cable is flexing while shifting between gears....More likely a transmission issue or something with the linkage?
View 24 Replies
This morning as I get in to drive my kid to school (2005 2.7 2 wd auto) as I go to put it in reverse I noticeably have to pull it with some force. I have never had to "force it" before, it had always switched gears with ease. This time it felt very stiff but had no issues going into gear. After I dropped my son off at school I went through the gears up and down and it felt very stiff (at this point i have no issues with starting it or P).
At lunch I go out to get something to eat and when I go to start it up it won't start. I try and try and nothing. All the lights came on, it's not a battery issue at all (brand new). But after 10 tries it starts, so I'm pretty happy. Then I go to put it in gear (reverse) I can not press in the button on the side of the gear shift. It will not go in. I press with all my might and it wont budge. But again, after about 10 good tries at it goes in and I can then select my gear but still feels very stiff.
After stopping again I didn't shut off the engine and dicked around with the shifter basically figured out that my car is not recognizing Park. On the instrument panel each gear lights up but not P. It gets very stiff when trying to put it in P but it doesn't actually go into P. If I put it in P (or really the further up it will go) and shut off the car, it won't start again. I can start it up in N and only N.
View 9 Replies
My cousin has a 2007 Ford Taurus with the pushrod 3.0L. It has the console shifter and it is hard to move the shift lever into Park from Reverse. The shifer moves out of park and to every other gear with normal effort. The gear indicator correctly displays the shifter position. It drives/shifts perfectly fine. The only problem is that it is hard to move the shifter from Reverse into Park. It feels like there is a rubbery, or somewhat mushy threshold/resistance that needs to be overcome with a moderate amount of effort to get the shifter into park. Once the shifter is in Park it feels normal meaning you don't have to hold or force the shifter to stay in park.
It is frustrating because it seems most other people have a problem with the shfiter being hard to move from Park to Reverse or Neutral, but she is having the opposite issue. Will it hurt the car to keep shoving the shifter into park when necessary without getting it fixed?
View 3 Replies
I have a Santa Fe Style CRDI Auto from 2011 which is not covered by Warranty and has only done 6000 miles.
The problem is that the Gear Stick Won't Move from the 'Park' position (with the engine on and brake fully pressed down).
There have been issues over the last couple of weeks where it was difficult to move the gear stick at times but it was fine after waiting a few seconds. Now it seems completely stuck.
View 7 Replies
I put the trans in gear it won't move and has a grinding sound and rolls unless I use the emergency brake. I bought this used from a friend at 80k miles, now it has 130k miles and has been factory serviced regularly.
View 1 Replies
I have a 09' 4cyl automatic engine with 54k.
About 30min ago when when I parked the shifter would not move past neutral into reverse and go into park. I can go from D into neutral or the next slot over for manual shifting. Naturally this causes a problem as you can't take the key out of the ignition if its not in park.
I took a screw driver and popped open the cap for the shift release button and used that to move it into park. Turned car off, back on, etc etc seemed fine. So when I tried moving it into reverse and it wouldn't budge. It instead would make a electronic click or snap coming form the steering column but more back toward the engine. Like more into the dash area but back in it. It would make this noise every time I attempted to move it but it wasn't a continuous sound. Just once with each jerk to the side to move it out of park.
So the car works fine except for this. I used it with the screw driver/shift release to unlock it and it drives fine. Goes into reverse and back in park but if I move it into neutral or drive it will not go back into reverse or park.
View 1 Replies
My 1996 Buick Park Avenue had problems finding reverse. You would have to move the shifter in and out of reverse and get it in just the right spot to go into reverse. once it is going in reverse you can hear a slight ticking sound like the park gear isn't totally disengaged. now it is nearly impossible to find reverse and when you put it in neutral its like it is in park.
View 2 Replies
I need removing the console on a 2005 Malibu Max. The switch on the shifter will not move the transmission down to 2nd or 1st gear. There was a post by "shadow5599" on 05-05-2009 stating that this problem was caused by a broken wire in the harness under the console leading to the shifter +/- switch. He said it was easy to fix but the console needed to be removed. Later on the same day he posted that he had just posted the instructions on how to remove it. I'm a first time user on this site and I haven't been able to locate those instructions.
View 1 Replies
I have a 2004 2.0L Jetta with a 5 Speed manual transmission.
When shifting into third gear sometimes I push the shifter forward and it does not want to move all the way forward. It feels like I am pushing the shifter knob against a wall, or more accurately the bottom of the shift that pulls the cables feels like it is hitting a wall. If I pull it back out and press it in hard it will go into place sometimes.
This also solves the problem: While the shifter is mid shift into third, at the wall/ at the point of resistance, I let off the clutch slightly to give the flywheel some friction. This rolls the transmission a bit and allows third gear to slide into place.
I have experience with a MK4 Audi TT 1.8T that cam with a 6-SPD and it at had a 1-2 and 2-3 synchronizer issue (The one where the nipples are worn and it grinds at higher RPMS because they can no longer make a firm handshake). The issue I am experiencing is not that.
Could it be the transmission cables? Could it be some other cogs in the transmission? - If so does this mean I need to buy a used one? My car has 180K miles on it with the original clutch.
View 5 Replies
My 2004 expedition wont go into any gear the shifter will not move I changed the stop light brake switch and a 30 amp buss fuse I found blown and also the check engine light is on now too this was after I parked it I also changed a 30 amp buss fuse I found blown out but it still don't work the only way I can get it into gear is to push the little button under steering wheel...
View 2 Replies
My 2000 ford excursion gauges fuse keeps popping. It started earlier this year and I couldn't pin point when it would pop. Now I'm sure after 30.00 worth of fuses that it happens when I change the gear shifter from park or rev to drive.
View 5 Replies
I have Hyundai Santa Fe, 2009 (automatic). when I start engine in the morning everything is fine except the reverse gear. the reverse gear moves to position easily but the car does not move. After 5 minutes of starting engine, the reverse gear works again.
View 1 Replies
So my friends 2002 camry has a problem where she shifts the shifter into drive, but the gear position indicator in the cluster still shows her in park, and the car will still be in park with parking pawl engaged. is this a sensor that went out, or a deeper transmission problem to be dealt with?
View 1 Replies
Experienced problem with the Automatic locks on the doors? The doors on my camry lock as soon as I move the shifter out of park. The owners manual indicates that I can get the doors to lock automatically at 20 km/hr. I have tried following the instructions in the manual to make this happen but without any success.
View 14 Replies
I have santafe 3.5 2012 4WD , it's 51K on odometer, the problem when cold startup , Noise and small vibrate form front side , its look like from gears
When put to reverse (R) sound is louder and strong vibration from front side, all this problem gone when drive about 15 minutes.
I have visit 3 local shop they check the engine, gear box, everything normal, no check indicator appears.
View 5 Replies
My '08 2.7 has difficulty starting in the morning. It makes the normal cranking noises but won't fire up immediately. I typically let it try to catch for 5-10 seconds, pause, and try again. Then I wait a minute, try again, and everything starts fine. Then it'll start normally the rest of the day.
Pardon my ignorance, but isn't there some sort of compartment that holds fuel into the engine with a check valve that keeps it from releasing back into the tank? Could it be that this valve is leaking?
Or does it sound like I need a whole new fuel pump? I tried to find schematics, but had no luck. I tired hmaservice.com, but I'm not willing to install the Adobe SVG app (obsolete and security risk) to view the documents.
View 2 Replies
I just did a motor swap on a 2003 with 3.5 auto tranny and awd. engine runs great and every thing is running fine. Only problem is that the trans will not create any power. With no drive shafts on it still wont move the splines. With that said the trans was driving/running great b4 the swap.
View 2 Replies
The shifter will not usually stay in 5th gear for very long. The clutch and flywheel were replaced a few weeks ago just before i purchased the car but this problem has only cropped up in the last week. Could it be shifter linkage adjustment?
View 3 Replies
The gear shift works fine, and we lifted the hood and saw that the mech. arm IS working when we shift. However, the van will not move into any gear. won't go forward, reverse, etc... it acts like it isn't shifting.
i was driving down the highway, and noticed it wasn't accelerating and stepped on the gas.. .and nothing. I stopped the van, put in park, turned it off. Started it again, and put in D and wouldn't go, just engine revved. then put in reverse and same thing... didn't move but engine revved.
View 3 Replies
My reverse lights and back up alarm will not engage unless i hold up on the shifter while in reverse the only thing i found was a adjuster for the indicator....
View 14 Replies
