I have an issue in my car (Santa fe 2011) and it occurred since it was new (ODO 3000 KM , ESP light is on and the 4WD Blinking) . the agency could not resolve the issue. and my car up to now been in and out from the workshop for more than 6 times . and more the error code ( C1627 ) that appears in the GDS(Global Diagnostic System) does not exist in the system (troubleshoot manual) .
View 5 RepliesI have a Low Oil Pressure warning light on. When it first came on, I stopped and check the oil level. It was low. I had to replace the oil 2 or 3 months ago, but then I had na accident (rollover) and just this past week i received the car and forgot to replace the oil. So that's what i did. Replaced the oil and filter.
The lights still comes on after driving about 3 or 4 miles. It starts by coming On and OFF a few times. Sometimes just blinking, than it stays ON until I shut of the engine. What it could be?
After the referred rollover, the engine shut off, but I turned it on less than 30 seconds after this (I know I shouldn't have done that) and drove for about a mile. Do you know if that would damage the engine or oil pump in 132,000 miles RX330?
I checked and found this error code P0346 (Camshaft position sensor). Would it be related?
Check engine light is on, when I went to get my car inspected it was showing an invalid vin code. How do get this off so I can get my emissions done?
2007 Santa Fe SE
I have a 2008 model 2.7 v6 with 80000 Km, and I would like to share my experience with several issues:
- Random misfire: brought the car to Hyundai, very bad response. I bought online the wiring of the spark plugs (according to them that was the reason of the misfire) and they installed it, did not improve. The car was still showing error code after clearing, and the fuel consumption at an average of 23L/100km.
- I then decided to change all the 6 spark plugs, no difference. The workshop told me the coils were in perfect condition. Still having a message like this: "ignition error on 2 or more spark plugs".
- I did a complete cleaning with contact spray of the MAF sensor.
- I bought online a couple of ignition coils, being original Hyundai ones, and changed them. When installing them i realized the existing ones were not original Hyundai and had a small marking, making me think they were recycled or chinese stuff.
- Having done that, the OBDII shown two more error codes: P341: error on camshaft position sensor, P2189: fuel idle (too much air, maybe caused by the first one). Changed both camshaft position sensors and then big change in the behaviour, more response, throttle, better gear switching.
- I so concluded that the 4 remaining coils have to be changed and ordered another time 4 of them online. OBDII showing now only one error code: random misfire. The engine going much better than all i got before.
- I have decided to take advantage of this order and also ordered a new TPS (seeing here that it was a common problem) and a Crankshaft position sensor (in order to prevent any other issue).
- I also changed previously 2 downstream o2 sensors that were giving an error related to emission. Emission here are not strictly controled so it is not a big issue.
My question is, what in all that sensors can more likely make my car burn 23L/100km??? Asian cities are quite similar to american cities, lots of highways. This consumption compared to what you describe is way over the normal one isn't it? I was assuming the ignition problem was the responsible, am i right?
I need to replace O2 Sensor which is Bank 2 Sensor 2 which needs to be replaced.
Where is this located on a 2009 Hyundai Santa Fe 3.3L
Month ago the malfunction indicator turned on. On checking it was found that wires over the engine were eaten by rats. Reconnection of wires solved the problem.
Today the malfunction indicator light is blinking. Could it be the same wires going loose?
I have a 2003 diesel GS Santa Fe, every now and then when driving the ABS light comes on, not very often but it does, if I switch the ignition off and restart it goes out, I had it on a fault finder computer and it showed code c1274, I think its something to do with the G sensor and the way it breaks (ABS) is it an easy fault to fix? What are the costs involved and will it affect the driving of the car, like I say it rarely comes on and I don't notice any change in how it drives.
View 1 RepliesEngine light come on and everything is running great, this morning got this error code U0d00. Went to advanced auto and had them run a scan.
View 5 RepliesI just bought a 2007 Santa Fe - There is a red light blinking at the bottom of the windshield (assuming thats the security) but there is also a strange blinking blue light right beneath the rear view mirror that is blinking on the windshield...
View 5 RepliesAt a bit over 43K miles the check engine light came on with a blinking cruise light. Dealer has confirmed that both secondary injection pumps have failed for reasons unknown. I think this is part of the pollution control system.
View 3 Replies2 error codes? Car runs fine - nothing seems wrong - the check engine light went on, so I pulled out the scanner which came up with the 2 codes: P0021 and P0022.
View 8 RepliesAt roughly 140,000 miles, my wife's '07 Santa Fe GLS has thrown a P0456 code. Does this code on a Santa Fe common?
It is "evaporative emission system leak detected (very small leak)." The good news, I guess, is that it is 'very small.' However, being small may make it more difficult to detect.
I've recently bought used Hyundai SantaFe 2007 and the engine check light lit up. I've bought EML327 OBD2 scanner, it showed P1405 meaning "EGR tempereature sensor incorrect". Some of my friends says it has something to do with CPF filter and EGR valve. They think, i should clean both CPF and EGR. Car service told me that DPF (not CPF) filter cleaning costs arround 350eu and one service told me to simply take it out and reprogram car computer. As far as EGR valve cleaning goes, no service wants to do this. I don't really know much about cars, so my main question is what would be my next step in trying to fix this error.
View 3 RepliesMy 2010 Santa Fe is only 2 month old and has 2000km now the check engine light is on. Went to the dealer and found out the code is P200A -Intake manifold runner performance. And they just clear the code. What does this code mean?
View 22 RepliesHave 2 problems that are giving me major problems.....especially with 100 degree heat in Dallas.
1. Ac stopped blowing cold last night out of blue. Still blows just not cold. Replaced bad fuse and drove for 5 minutes. Blew again. Checked out the control/ circuit board but looks ok. Really cant afford dealer.
2. Check engine light problem for months. Gas gauge wasn't working. Replaced fuel sending units and it fixed that but still light. Code says p441. Dealer said need solenoid valve. Replaced both the solenoid valve and the purge control valve. Still check engine light.
About 4 months ago, I had the battery replaced since the car was not starting easily and they said voltage was not good. They also shimmed the ignition coil at the same time. I thought it was a bit early for a new battery but ok.
Last Friday I started getting a flashing battery light on the console but no other issues. Thought I would bring it in Monday.
Sunday I was driving on the highway and all warning lights came on, flashing, console died then came back on with a bunch of warning lights and then the car died. I managed to get off the highway with about 10% power and park in a lot. Car would not start once I turned it off, click, click, click, click like no power etc but rest of power in car seemed fine. Started fine Monday morning and I drove it to the dealership.
The dealership says the code was P2502 (Charging System Voltage). They are going to replace the Battery Sensor first and then if that doesn't work replace the Alternator.
I've checked the lines from the Purge Valve on the Passenger side of the Intake Manifold, Check OK
I've Checked that Valve OK
I've Replaced the Canister Close Valve
I've got the Gas Cap tight.
I've removed the rubber bushing holding the CCV to the Evap Canister, hoping to isolate the Filter and point the blame on it, no luck there!!
I'm thinking next is to drop the Tank and check over all the Goodies on top.... as much as I hate the thought of that, the two access holes under the seats, just don't allow access to enough of the tank!
any thing there that I could suspect, I see there's a check valve!
There's also the Fuel Tank Pressure Sensor, which may be at fault.
2012 Santy V6 GLS Stock 17"
Lately in an intermittent fashion my TPMS indicator light will blink when I first start the car. It goes away within a minute of driving (might even go away if I just idle but I am always in a rush so I don't know...). At first I thought perhaps it was the cold weather but it happens even on warm days. I've checked all the pressures all around and they are good (not even borderline).
In the manual it says a malfunction is when the light blinks and then stays on. What would blinking then non persistent light mean? Communication issues?
It seems that i'm most likely going to have to replace the entire plenum .
P1159 here are some details. [URL]..................
I've checked all connecting wires and none appear to be loose. When the issue started to occur and prior to discovering the P1159 code, I also replaced all coils. I replaced the coils because one was arching over to the metal of the engine. I assumed this may be my problem. The issue still persisted obviously. The check engine light never came on so I assumed I wouldn't get a code. I took it over to a friends house with a code reader and that's when I discovered that it was actually giving the P1159 code.
Are there any other model cars that utilize the same engine that I could use the plenum from? Getting this in working condition is going to be the difference in what I can get for it.
So the check engine sign came up on my car and using the OBD it tells me the error is P0113. After googling the information, it looks like I have an issue with IAT sensor.
I opened the air filter and what I believe what could be the sensor and there was nothing clogging up, so I'm assuming the sensor needs to be replaced
Question is where is the IAT sensor located and how do I dis-assemble it so I can replace it. Is it the piece that is located just before the air filter?
I just joined the forum mainly to care of my dads 2001 Hyundai Santa Fe but also I got a check engine light on my way home from work last night.
From last night I saw that oil was all over the timing belt. Today I inspected it with a Coworker and his OBD II reader.
Error Code was P0455, EVAP - Evaporative Emission Control System Leak Detected (gross leak).
Now the oil leak is stronger since the oil spills is on hood (inside hood). I will make a picture tonight when I get home.
I personal think it's leaking from a tube/ valve on top of the timing belt (picture will show more tonight). Thinking of cleaning the timing belt area, then drive a little around or leave it in idle to spot where the leak is from.
Common issue? I googled around but since P0455 is a common issue (on my 9-2x as well) I couldn't find anything about this I am also limited from my search since I am currently at my work PC incl. strong firewall.
I will see if google let me find a picture...