Santa Fe (CM - 2007-12) :: Codes P0021 And P0022 After Oil Change And Alignment
May 31, 2015
I took my 2009 Santa Fe Limited in to Firesteone last Friday. After the oil change and alignment, I drove out without any issues. Current mileage is 61k+.
I was running some other errands and drove about 20 miles to the next destination and parked. Came back within 45 mins and started the car when 2 lights came up on the dash - malfunction indicator lamp and engine oil pressure warning light.
I called the Firestone service center who suggested another location closer to my current position. The guy at the other location checked the error codes with the scanner which came up with P0021 and P0022.
Now, I am not very handy with anything car related and my vehicle is just out of factory warranty by 3 months and 1200 miles. I am concerned that these error codes point to expensive repairs.
Are these issues common in my model? The car seems to run fine. Could this only be the sensors or oil valves?
Assuming the worst case scenario, how long should I be able to drive before immediate need for repairs or without making the issue worse?
View 7 Replies
Advertisement
2 error codes? Car runs fine - nothing seems wrong - the check engine light went on, so I pulled out the scanner which came up with the 2 codes: P0021 and P0022.
View 8 Replies
I have a 2007 F-150 5.4L and it started throwing codes p0012 p0022 p0345 and would knock and make popping sounds after it warmed up but I could rev it up and it would go away for the most part but would come right back when I started driving it. I have since pulled down the front cover and made sure it was in time, replaced both cam phasers, replaced both vct solenoids, and replaced both cam sensors. Same issue after doing all of that. I have searched the internet and have come up with nothing.
View 3 Replies
So I have an 05 Expedition (I know this is the F-150 forum, but more visibility) that is throwing a P0022 and P0345. I get these point to the cam phasers, so before I throw $450 on a phaser kit and oil pump, I want to make sure its a good fix.
I have done a lot of research on this forum and other where people have replaced their phasers and it doesn't end up fixing the issue. So I just was looking to get some tips before I endup shot gunning parts.
View 7 Replies
I have a 2009 Santa Fe Limited (2 wheel drive) that pulls to the left a little while driving.
Before taking it in for an alignment, need to know whether or not both the front toe and the camber are adjustable on this vehicle?
View 7 Replies
I'm having the well known situation with P0345, P0022
Replaced both phasers, replaced cam sensor, checked timing (properly aligned), assembled back still running rough and rattling, used 10w40 oil,
Complete rebuilt engine, we did head work new seals and springs, valves are straight I had it checked out twice for assurance. New pistons, new rings, new bearings, new oil pump and seals of course. If I disconnect cam sensor Bank 2 it works fine but still runs a little rough.
- Replaced one tensioner due to gasket wear.
- I was told to check on alternator ground (it's missing I know cause it got broken and I haven't replaced that ground that goes into the engine.)
- I also was told change oil to 5w20 and filter (Not FRAM), add some lucas and it should be the fix.
- Also told to disconnect the oil pressure sensor and it would fix the problem but it will throw a code for that.
- I haven't replaced the timing chains I feel they're a little loose but they haven't jumped the teeth, so I guess they're good.
- I saw in one thread to move a teeth on phaser giving me code bank 2 (moved one teeth back and then one teeth forward but it didn't work)
When I first rebuilt the engine I was having the rough iddle then I scanned it and it gave me the cam positioning sensor code P0345, then after I replaced it problem got fixed and code was gone, I was using the truck for 2 days with no issues, then the problem cam back with the two codes P0345 and P0022!
View 13 Replies
The wife and I took her Santa Fe to our local dealer yesterday afternoon for an oil service. I take them a Mobil 1 5 quart jug of 5w20, and they supply the factory filter.
At any rate, today while she was running errands today the battery light comes on. As I suspected, the alternator is not charging. The battery is good and strong, but I do not know if it will run the car for the 25 mile drive back to the dealer.
I also see that the alternator is directly below the oil snout where the tech would have put the new oil back in yesterday. I am wondering if he drenched it in oil, and thus the reason for the light.
View 20 Replies
My windshield washer tank is leaking, need instructions on how I can fix it myself? Does the phone bumper have to come off, or is there a simple way to remove/replace it?
View 7 Replies
I would like to upgrade my rims, from originally 18 inch Champion to the Omanyt, but I once heard that it is necessary to change the wheel alignment (german: spur and sturz) if you want to use the 19 inch VW Omanyt (ET40 255/40 R19) rims on Phaetons that were shipped with 18 inch wheels. Is this correct?
View 4 Replies
2010 UK Santa Fe manual box, suddenly will not set Cruise Control. At same time gear change advisory indicator also stopped working. OBDII tester will not initiate to check things out but first time I have tried this. Fuses checked all OK (I think).
View 1 Replies
I was driving today and at a traffic light a severe smell of burnt plastic filled the cabin and the A/C blower started to change speed than stayed at full blast and even if I'd turn the knob from side to side or tried to shut everything off with the ""OFF""button nothing would happen........so we drove home and at some point it shut itself off...tried it again and seems ok now.....every dealer closed today and leaving for the USA tomorrow morning.... What the problem could be?
View 5 Replies
My wife has a 09 Santa Fe and we were getting code p0464 fuel sensor circuit intermittent. I changed both parts that need replacing. After about 20 miles now code p0442 small evap leak detected. I can only assume that it is coming from the fuel sensors that were replaced. Is there anything that I could have screwed up on?
View 1 Replies
My 2008 just showed the light at 108,000 kms. Its a long drive to the dealers. My old Hondas would flash a code number in the instrument cluster if I shorted out a pin under the dash. Is there a way to do this with the Fe?
View 6 Replies
2008 base model. A couple of years ago, I noticed whenever I changed my climate controls to defrost or bi-level, there was a 'gurgling' noise coming from behind the panel as the mechanism switched. Several months ago, the gurgling stopped as did the ability for me to change where the fans vents. Right now it is stuck on bi-level. something similar happened in a work truck the other day and I easily traced it to a small tube that had detached from a plug. I am wondering if the climate controls in the Santa Fe are also vacuum controlled and, if so, where might I find this tube?
View 2 Replies
My 07 3.3 SF is throwing P0154 and P0300 codes. Autozone said the P0154 is Bank 2 pre-cat O2 sensor. But exactly which one? The P0300 is random misfire. Could they be related?
View 7 Replies
I have been having this same problem over and over again. Check engine light comes on with P2127 and P2106 codes. 1st time they said they needed to flash the computer. Worked fine for maybe 6 months and then again. While this is happening you cant go over 2500 rmp with it floored and takes forever to get up to 60-80 kph which is the fastest it will go. Sometimes after starting stopping 5-8 times it will be fine. The second time they replaced the gas pedal because the sensor was deemed bad. Now about 8 months later here up it comes again. This time I was pulling my boat and I thought I wasn't going to make it up the hill. I don't trust this car anymore especially for long trips. So anyway they updated the computer again, and then 4 days later up it comes again. Also inner tie rod ends I have replaced 3, just so you know I only have 52000 kms on this 2008.
View 10 Replies
I have the 2011 Santa Fe V6 and it has the P0447 & P0455 codes popping up on my reader. I checked the pins to make sure that there is voltage getting to the solenoid, (about 11volts at the 2 pins) and it seems good. No fuel lines broken, or cap messed up, etc.
View 6 Replies
2007 Hyundai Santa Fe Limited, 3.3l engine, 2wd, about 110k miles
I recently replaced my neutral safety switch, but wasn't able to run codes at that time. The fuel level sensors need to be replaced, but haven't gotten to it yet. The usual P0463, P2068, and P0464 codes are active.
The following greyed out codes came up in a scan, and I searched this forum (and google) and found little info.
Mystery greyed out codes are: C2820, P2019, U1904.
Codes were reset with no problem...
View 1 Replies
I have a 2005 F-150 4x2 with 4.2L mojo. If I change the struts, is an alignment required due to slight changes in the top mount location? I plan on having it aligned but timing wise I may not be able to get it all done at the same time.
View 1 Replies
So a couple days ago i replaced the fuel level sensors in my 07 gls 2.7 liter santa fe and all was well for 2 days. I had finally driven it enough that the codes cleared from active status and the car turned off the cel. However, during the same ignition cycle the engine started missing a bit and the cel came back on and started flashing at me. Codes found now are p2187 lean bank one and p2189 lean bank two, plus p0302 misfire detected cyl 2. I've tried the carb cleaner trick looking for a vacuum leak.. but no luck. Air intake boot is good vacuum lines look good etc. What might be going on? Did i get debris in the tank and glog an injector with it? Fuel pump itself appears to be operational. No bogging down or loss of power under heavy acceleration.
View 1 Replies
We have a 2006 CM later model Santa Fe 2.2 CDX+ 7 seater. Engine light came on last week and since then car does not shift into 4th gear. It revs very high upto 5000rpm with no increase in speed, it's limited to 30-35mph.
I had this problem back in 2010 where the Hyundai franchise identified a fault with the EGR which was replaced under warranty, and then a year later a problem with the fuel sensor which was also replaced.
I had the local garage check the EGR and give it a clean based on the steps provided by a member here - no change. So I took it to Hyundai but this time, they are reporting fault codes P0733 and P0744 which point to transmission problems. I just had a call from the garage who say they believe the gear synchromesh is jamming thus not allowing the change of gears. He said that the diagnostics report that the car is sending the gear change command correctly (pulse generator ok) so does not believe it is an electrical fault.
View 29 Replies
