My 2010 Santa Fe is only 2 month old and has 2000km now the check engine light is on. Went to the dealer and found out the code is P200A -Intake manifold runner performance. And they just clear the code. What does this code mean?
View 22 RepliesAt roughly 140,000 miles, my wife's '07 Santa Fe GLS has thrown a P0456 code. Does this code on a Santa Fe common?
It is "evaporative emission system leak detected (very small leak)." The good news, I guess, is that it is 'very small.' However, being small may make it more difficult to detect.
I've recently bought used Hyundai SantaFe 2007 and the engine check light lit up. I've bought EML327 OBD2 scanner, it showed P1405 meaning "EGR tempereature sensor incorrect". Some of my friends says it has something to do with CPF filter and EGR valve. They think, i should clean both CPF and EGR. Car service told me that DPF (not CPF) filter cleaning costs arround 350eu and one service told me to simply take it out and reprogram car computer. As far as EGR valve cleaning goes, no service wants to do this. I don't really know much about cars, so my main question is what would be my next step in trying to fix this error.
View 3 RepliesHave 2 problems that are giving me major problems.....especially with 100 degree heat in Dallas.
1. Ac stopped blowing cold last night out of blue. Still blows just not cold. Replaced bad fuse and drove for 5 minutes. Blew again. Checked out the control/ circuit board but looks ok. Really cant afford dealer.
2. Check engine light problem for months. Gas gauge wasn't working. Replaced fuel sending units and it fixed that but still light. Code says p441. Dealer said need solenoid valve. Replaced both the solenoid valve and the purge control valve. Still check engine light.
Check engine light on, car stalled once. Pulling code p0320 "Engine Speed Input Circuit Malfunction." Tachometer works intermittently. Where do I start?
View 2 RepliesRecently got check engine light fault code p0320
2005 3.5 with 172k miles
I have a 2009 Santa Fe, v6, and the check engine light and "ESC OFF" lights are on consistently.
I read the check engine light may be the gas cap so I replaced it but the light is still on. Took the car to Advanced Auto Parts and they said it was related to the cruise control.
I also read that the ESC OFF light may be due to alignment issues. I had an alignment done last Saturday but the light is still on. When they checked the check engine light they said it was related to the emissions. This was at a Firestone shop.
Any common cause for these lights to be on at 30,000 miles? I changed the transmission fluid also recently which the manual says to do at 30,000 miles.
I own the 2014 Santa fe turbo 2.0 litre limited which has 4000 km on it. Within 210 km the engine light came on 3 times. I took it into the shop and they ran a code of P0303 which is a misfire, they changed the coils #2 and #3 and cleared the code. The second time it showed the same code but the shop said it was in the history so that is why the same code came up again. They ran an update ECM? and all was good. Now the 3rd time they tell me no code has come up and can't do anything about the engine (they cleared it) but it was like chasing ghosts. My vehicle runs great so not sure why I am constantly having this issue.
View 68 RepliesMy check engine light came on the other day and the code stated the the "throttle position is open" so after researching and everyone telling me that i need to change the sensor. I did everything after was fine running better but today only after 3 days replacing it i get the same problems. car has no get up and go hardly can push to 20 mph and when in idle i press the break it starts to bog down and almost want to shut off! and can be really loud...
Santa fe 05' 3.5L ....
i have a 2008 santa fe with a 2.7 61,000 miles 2nd owner ,out of warranty. It started missing and the check engine light came on. I took it to a local parts store who put an analyzer on it an it showed the #3 spark plug was misfiring. I am hoping its the plug. I do my own work but havn`t been able to find a correct sequence to replace the plugs.
View 3 RepliesI recently bought a Santa fe 2007 Limited 3.3L, it has 101500 miles. The issue is that when i run the scan it has 3 minor sensors that needs to be replaced but my biggest concern is that the check engine light does not come on in the dashboard even when i turn the ignition to on.
I need to know if there is a fuse that can cause this or a bulb in the dashboard that i can replaced for myself or if it is something else.
I have a 2008 Santa Fe with 64341 miles on it. This past weekend we had it inspected at the dealer. Drove it home, in the rain/snow, and it sat in the drive way for a day while it was raining. This morning when I went to go to work, still raining, the check engine light came on and was flashing. Went to auto zone to get the check engine light code, the said that it was a P0303 which according to them was a misfire in cylinder 3. So I brought it to the dealer to leave it and have them check it out. On the way their the check engine light started to flash, when I walked in and told the service desk that they said that it was a catastrophic failure.
View 10 RepliesI have a 2011 Santa Fe 3.5 6, FWD, 54k miles, that has been having the check engine light go on and off. Recently with in the pass month and a half the dealership has perform the recall adjustment, changed the manifold intake assy, changed the ECM with all visits rendered a P200A code. After changing the manifold assy, check engine light was off and fuel gage was at a 1/4 tank. Stop by a gas station and filled up and the light comes on. Remove gas cap after turning off engine and secured gas cap as directed on the cap of one click and light stays on. Turning into the dealership for the 4th time.
View 4 RepliesMy 2008 just showed the light at 108,000 kms. Its a long drive to the dealers. My old Hondas would flash a code number in the instrument cluster if I shorted out a pin under the dash. Is there a way to do this with the Fe?
View 6 RepliesTo start off with I am not car smart! I have a 2008 Santa Fe 3.3L V6. Last year about this time (December) I had problems with the vehicle upon start up would be miss firing and the check engine light would come on. I would turn the vehicle off and restart and it would be fine and not happen again sometimes for a week and sometimes for months. I hooked it up to the computer and found that it was missing on the #6 cylinder. I had the coil pack replaced and that seemed to fix the problem (replaced spring 2011). About a week ago it started doing the same thing (December 1). Upon initial start up when the car is cold and the outside air is very cold it started missing again and having a rough idle. Would turn of the car and restart and would run fine but check engine light would come on.
Hooked it up to the computer once again and it read random misfire. This has happened twice now in two weeks with the same reading each time. Always when it is cold (engine and outside temp) and seems to reset itself when turned off.
I spoke with a mechanic who recently had this same issue with a different vehicle and after trying many things replaced the engine coolant temp sensor and that did the trick. He said it was a cheap start therefore i bought the part and now am looking to replace it. The only problem being i am car dumb and cant find it. I have done many searches and the diagrams i have found don't do me any justice. The past posts on here have given pictures of older models that dont match what i am looking at. It probably is right in front of my face. Any picture of a 2008 that will show the correct area I should be looking at? The vehicle only has about 57,000 miles on it.
My 2007 Sante Fe had problem this week. Took 6 attempts to start engine, then ran smoothly the rest of the night. The check engine light came on while trying to start vehicle.
Next day I changed the spark plugs but now find that the vehicle jerks when idling. Runs fine when going but jerks and bucks at stop lights and stop signs. Just added fuel injection cleaner to see if that may support the situation.
Engine light has come back on again since resetting. I have read several suggestions on internet regarding leak in vacuum line, Coil Pack damage due to faulty hose, even faulty 02 sensor.
I have been having this same problem over and over again. Check engine light comes on with P2127 and P2106 codes. 1st time they said they needed to flash the computer. Worked fine for maybe 6 months and then again. While this is happening you cant go over 2500 rmp with it floored and takes forever to get up to 60-80 kph which is the fastest it will go. Sometimes after starting stopping 5-8 times it will be fine. The second time they replaced the gas pedal because the sensor was deemed bad. Now about 8 months later here up it comes again. This time I was pulling my boat and I thought I wasn't going to make it up the hill. I don't trust this car anymore especially for long trips. So anyway they updated the computer again, and then 4 days later up it comes again. Also inner tie rod ends I have replaced 3, just so you know I only have 52000 kms on this 2008.
View 10 RepliesI have an 08 Hyundai Santa Fe. Check engine light comes on, fuel gauge goes from empty to full, to half, to 1/4, just all over the place. Even ran out of gas a few times on the side of the road not knowing how much fuel I have.
What exactly causes this problem? I've heard "fuel sender" I've heard "fuel pressure sensor" etc. All are different parts. Need to get this repaired asap.
My wife's car has 83000 miles on it. We bought it as a factory certified pre-owned vehicle with about 1800 miles on it and it came with the warranty. For the last two years the check engine light comes on with code 441 I don't worry about it till time to get inspection sticker here in Texas. I have been about to reset the computer and drive it till the computer is ready to be inspected and it has passed for two years. Now it won't reset and I have tried to test the vacuum switch and it seems to click when I apply voltage but light won't go off. This code can cost up to about 2000.00 to try and detect. I am not interested in having the dealership keep guessing on my dime.
View 2 RepliesI have an '09 LS SWB AWD with 86k miles on it. A few days ago the check engine light came on with a message on the dash for me to check the VSC system. The next day the check engine light and VSC warning went away on their own. A day after that they came back on. I pulled the ODB codes and got the following:
P0012 - "A" Camshaft Position - Timing Over-Retarded Bank 1
I took it to my local Lexus dealership and they determined that my VVT-i motor assembly needed replacing. Total cost would be $1,222. Apparently this part regulate the camshaft for variable valve timing. I asked if I should notice a performance dropoff since it's related to valve timing but they said no. They said I wouldn't make it worse by driving it so I took my car back and they would order the part for me.
The next day the check engine light and VSC warning went away on their own again and have not come back on for 3 days now. I don't understand why the warning and check engine lights keep going off on their own if this motor assembly needs replacing. Once again it has been 3 days now and no lights have come on.
I am the proud owner of a 2008 LS600hl with 141,000 miles. The check engine light is now on permanently and the estimated repair charge from my lexus dealership is outrageously expensive. Here is the official diagnosis and recommendation.
"Code P1083 - HCAC Valve Stuck Open in Bank 2 .
Recommend Replacing Y- Pipe With HC Adsorber .
Possibly May Need Exhaust 2 Sensors.