I have a 2007 Santa Fe crdi automaticl. When I push the 4 wheel drive button, the light in the dash goes on but the axels do not lock up. There is no code number that show up. Is this a sensor problem or what?
View 1 RepliesSo my Push Button 4 wheel drive wont engage. The light on the dash wont light up and it doesn't shift into 4x4. Where to start? I would like to check the simple stuff first. O and my heat only gets hot when im giving the vehicle gas. This is all on a 2003 Ford Explorer.
View 2 RepliesIts a automatic transmission with a v6 4.3 vortec. The front axle will not engage, it is not the acuator (I replaced it and the cable) you can pull the cable and the axle will engage. There is a low buzzing noise(coming from the drivers side) until you give it gas. This noise stops when the front axle is engaged. The transfer case will go from hi to low without any problems.
View 1 RepliesWhen I push the button or use the fob to open the trunk, it opens but the trunk lid does not pop up. I have to pull it up manually. Is there some trick I'm missing? I skimmed the manual but didn't find anything.
I found my answer. Apparently they don't pop open on the older models, which is ridiculous. They started putting that option on cars years ago! Unbelievable.
The gas door won't open. I hear clicking when I push the release button but the door won't pop open. I don't even have enough gas to get to the dealer.
View 12 RepliesNeed to change a starter of an ls460? My car died on me yesterday and i strongly feel its the starter. When i push the start button i get a loud click noise.. after playing with it for 20 min it actually started. Battery is good, no codes..
View 14 RepliesI have an 01 s10 with the 3 switch 4x4. When I switch into 4hi I hear the click at the dash and I hear the switch on the transfer case but it doesn't engage in 4x4. The lights o. The dash act normal and says its in 4 wheel. I've had problems with the switch on the front of the transfer case in the past and was able to clean it and it was OK for awhile and now nothing. I replaced that switch and hear it working but still not engaging. I did notice a bad vac line on the firewall but not sure where it goes yet. Is there an order I should be checking components? What should I look for next? Also should mention in 2hi I get a whining noise like a shaft is spinning but when in 4hi the noise goes away and it drives like its in 2hi.
View 1 RepliesSanta Fe 2013. I bought it a few months ago and soon after a strange issue appeared from time to time. When I push the start/stop button it spins the engine but it wont start no matter how much I wait. Usually it start fine for the second time. This happens sometimes and sometimes not. About 2 months ago it didn't want to start for about 5-10 minutes no matter what I tried (push the button with the tip of the key), so I decided to go to a service station.
There they connected the car to a computer to check if there were any error codes logged. But they haven't find anything, after the second time I visited the station they replaced the battery in the key, told that maybe that was the problem.
I really don't know much about cars but it was a strange idea as I would expect the same behaviour when the battery is low than when the key is not present: Car not doing anything but displaying a message that the key is not present.
Anyway, it kinda worked, or I was lucky. For more than a month everything was fine, not a single issue. And today morning it started again. I brought my car to a hand washing, and after they cleaned the outside with steam they wanted to park the car inside the building to clean the interior, and the same issue occurred. And after that it happened with me as well several times this day.
2007 Prius is not starting. The power doors, lamps, and headlights work. 12V battering showing 13v on multimeter. When you press power button with/without key FOB in, power button shows green but car does not engage.
View 3 RepliesI have a 2003 3.5 liter, AWD and I'm attempting to remove and replace the drive axle on the passenger side. I have the one end out of the hub, but the transmission end will not come out. I removed the bolts holding the bearing plate, and have been trying to pry out the axle with no luck.
View 3 Replieson a 93' 4 runner that will not engage 4 wheel drive. The 4 wheel manual shifter works fine, and the linkage underneath looks fine; however, the indicator does not light up - and it definately only has rear wheel drive.
View 5 RepliesAfter I push the switch for the 4 wheel drive, the light on the dash blinks but the front differential won't lock in even after driving around the block.
View 14 RepliesI bought a 99 ranger few months ago cant the 4x4 has not worked in the truck for about 4 years. Bought it off my dad. He hasn't figured it out the t case locks in the drive shaft spins but hubs will not lock in. Has new hubs in it and still not working. Trying to get it fixed so I can park the diesel for the winter and run the ranger.
View 3 RepliesI have a 1998 F-150 and when shifting into 4 wheel drive (manual floor mount shifter) the drive shaft from the transfer case turns but the wheels do not engage.
Looking for a diagram of how the axle works?
I have just switched from GM to Ford and have a new F250 4x4 XLT. I am wondering how to engage 4 wheel drive correctly. I have the manual shifter and the manual lock hubs. However during my test drive I shifted the lever into 4H and 4L and it seemed to engage just fine. Do I need to lock my hubs as well? Or if im just in a wet spot can i just shift into 4h without locking my hubs? I know if I am in anything serious I need to lock the hubs. I just want to be sure before I get into a tricky situation. My 02 GM all i had to do was push a button and it shifted automatically.
View 7 RepliesSo now that it is becoming colder out (40's in the morning 50's in afternoon) I have been experiencing signs that an inner joint on one of my axles is going bad. When driving while the vehicle is still cold, and even when it is just warmed up, I have bad vibrations while accelerating. I've ruled out other things and even had the car in the air and had it checked out at a stealership but of course they couldn't reproduce any of the vibrations. It was warm out the day of the appointment.
View 6 RepliesI have a 2001 f250 7.3 powerstroke it is an automatic. It has the switch on the dash to engage the 4 wheel drive. When I turn the switch nothing happens.. no lights come on or anything. it has warren locking hubs. What my problem is???
View 2 RepliesI recently purchased a 2003 F350 FX4 Dually with the 7.3L Diesel. It has locking hubs and electric shift in the cab.
I have had locking hubs before that you had to engage to shift into 4 wheel drive and I have had trucks without locking hubs.
My truck didn't come with a manual, so I am looking for instructions for the proper use of this system.
So the other day I was changing the oil on the SF, and I noticed a glob of grease (fist sized) on the passenger side of the frame. After cleaning up the mess it appeared that the grease was coming from the inner CV boot on the passenger side. From my position under the SF I could not see any obvious crack in the boot, and I also squeezed the boot and ran my finger around it in each of the bellows. I still didn't find any rupture. I then began to wonder if the boot had slipped off of the base of the axle. I pushed and pulled on the boot and could not really budge it.
In full disclosure I did change the front struts 2 weeks prior. My only thought is maybe I pulled the boot off somehow during that job. If that was the case though wouldn't I be able to move/dislodge the boot now?
FWIW there is no noise coming from the passenger side that would indicate the CV joint is bad or on its way out.
I have an 8 month old vehicle that will not lock the driver side door lock (using the power lock, fob and/or when you take the vehicle out of park). The issue seems to go away, but returns usually right after I get it back from the dealership. On a side note all of the other door locks activate and deactivate fine.
View 7 RepliesI have 2007 Santa Fe LTD which will intermittently not start. All electrical devices work fine but when you turn the key the starter will not engage. Keep trying the key and after 5-10-100 try's the car will start. The next time it may start on the first attempt or it might not. Sometimes it will go weeks without a problem then it will not start again. I have checked the starter relay, battery, and cables. It seems like the alarm is faulty and not letting the power get to the starter.
View 16 Replies