Santa Fe (CM - 2007-12) :: 2008 Limp Mode - CEL / ESC And AWD Transmission Lights Blinking
Oct 2, 2011
I'm a little bit stuck here. This happened last night, and the dealer is closed today. I have a 2008 Santa Fe SE. It stalled last night, and when I turned it back on, I got a check engine light, the ESC light, and the AWD transmission light blinking. When I go to accelerate, it will not go passed 2000 RPM, and it is driving very sluggish. Its not knocking, or making any other kind of sounds. The air conditioning does not work, but the fan blows uncooled air. It accelerates extremely slowly, even with the petal mashed.
I plan on taking it in tomorrow, but I'd like to know if there is some way to reset the computer. I tried disconnecting the battery for about 30 minutes, but it didn't work.
View 2 Replies
Advertisement
My 2007 Santa Fe was acting up at one time, then stopped doing it, and recently started again. My wife is the primary driver so I'm not always in the vehicle when it happens. When the vehicle is started cold, it will run a short distance then the MIL comes on and it goes to a 5 mph limp mode. After pulling over and shutting the vehicle completely down for a couple of minutes, it will run normally with the MIL still on. However, by the time I get back home to pull the codes, the MIL goes off. I don't remember the exact codes, but when it acted up last time I believe the codes had something to do with the TPS, Pedal Pos Sensor, and one other I can't remember.
View 3 Replies
Driving on the motorway yesterday, all fine until i lost power..engine light came on, but I was able to continue driving for about 6 miles (trying to get to services) but eventually it would go no further, pulled over and found that the intercooler pipe had come off, replaced it but still no joy.
Recovery van attended and plugged in diagnostic and found a dpf fault and gas pressure valve fault, he cleared the light but i think the faults still remained.. so i had to be recovered home.
The engine will start but it does not quiet sound right, no response from the throttle and if i put it into drive the engine stops.. Its a 2007 2.2
View 5 Replies
33K and no problems until this morning. Wife gets 400 yards down the street, car "lurches" and goes into limp mode. Transmission won't shift out of whatever gear its stuck in (going forward) Car will back up. Only indication of any possible trouble is occasionally the very first time the transmission shifts in the morning from 1st into 2nd its a little spirited rather than silky smooth.
View 5 Replies
2002 Santa Fe, 2.7 AWD
The transmission has started going into limp mode and causing the check engine light to come on.
The codes given are p0750 and.... I think p0751, for shift solenoids C and D. There is also the generic Transmission Control Module code.
Limp mode only occurs at higher speeds although shifting feels a little rough at times in lower speeds.
If operated in manual mode the vehicle can be driven normally at all speeds without going into limp mode.
Fluid levels are fine.
With limp mode occurring in automatic but not occurring in manual mode, is it more reasonable to believe the solenoids are malfunctioning or the control module itself? I'm inclined to replace the solenoids but find it odd that the vehicle operates normally in manual. Also, can the solenoids be replaced without removing the transmission? It looks like I could get the pan off but am unsure if there is room to get the work done once it is removed.
View 2 Replies
I have a 2005 2.7L Santa Fe that was shifting poorly and getting stuck in limp mode intermittently. I read up on it and found that it was probably an issue with the input/output speed sensors. The codes confirmed my suspicions and I replaced both the input and output sensors. The codes cleared and the tranny shifted like a dream. Unfortunately after 2 days and 100+ miles the car suddenly started down shifting randomly on my way home from work. The CEL came back on and the car went into limp mode. Could the sensor have gone bad again? Or could it be the wiring harness that plugs into one of the sensors? I don't understand why the car would be fine for a few days and then all of a sudden be acting the same way.
View 6 Replies
I just got an Egde Evo which I installed and everything looked great. After a few runs, I noticed the ABS light coming on an soon after that my transmission goes to limp mode (the wrench lights up).
I receive the DTC error: P2106 on the Edge Evo.
I have gone back to Factory default, but it keeps coming back, ie. the ABS light lights up and the Trans goes to Forced Limited Power (according to the Evo).
View 6 Replies
I have a 2008 F350 with a 6.4 Powerstroke diesel engine that just experienced total engine failure. It has around 65K miles.
There is a heavy burn star pattern on all 8 pistons, a few pistons are cracked, a few cylinder walls are scored, glow plugs are melted, both heads are cracked with multiple stress fractures in each head.
About 1 month previously, the transmission would not work in tow mode and caused the engine to go into limp home mode. The dealership just replaced the entire tranny as a warranty item. About 1 week before the engine failure, I put in a 5.25 oz bottle of Lucas injector cleaner with a full tank of gas.
The Ford dealership is saying that the star pattern on all 8 pistons is due to high pressure fuel overspray and is evidence that I had a tuner on this engine and that the warranty is invalid. I did not have a tuner. What might have caused this engine failure?
Also, they only ripped down the top half of the motor, not the bottom half. I heard this might have been caused by a cracked crank shaft, but Ford refuses to investigate this possibility.
View 14 Replies
I have been having a problem where the Santa Fe will drive great for a week, sometimes only a day and the engine light will come on and the car will go into limp mode. It will drop you from 65MPH to 10 MPH, if you put it in park the RPM's will race and stomping on the pedal will not affect the RPM's. After you turn it off for a couple of minutes it will drive ok again. I have replaced the Throttle Position Sensor and the Accelerator Pedal Sensor, cleaned all connections and checked wires in them. I have also cleaned the Throttle Body. The Dealer wants to replace the Throttle Body.
Had Engine Codes:
P0123 - Throttle Position Sensor 1 Signal Circuit High Imput
P1110 - Throttle Actuator Control System Malfuntion
P0222 - Throttle Position Sensor 2 Signal Circuit Low Imput
P1175 - Electric Throttle Valve Control System (ETS) Valve #
P1196 - Throttle Actuator Control System Limp Home-Stuck
View 3 Replies
My wife has a 2006 santa fe 3.5l limited over the winter it started acting up went into limp mode and would only go 20mph so I went and picked up a TP sensor well it went out of limp mode so I never changed the sensor well last month it started doing it again so I changed it out didn't work!!! comes up with 2 codes sometimes p2110 and p2118 but normally its p2110 2 times.
If I hit the break it kinda bogs down and pulsates.i took it to my mechanic since I couldn't figure it out and with advice from a hyundai mech. He changed APS didn't fix it so we changed throttle body with used of course didn't work I checked wires and didn't fined any open circuits what are the chances that i got a bad APS or TPS...
View 3 Replies
My Jetta mkiv transmission went into limp mode recently. Took it into shop. They checked it out and they replaced solenoids as well as the TCU. Car still goes into limp mode. It doesn't happen all the time but enough to piss me off. Any thoughts?? Car only has 140000 miles.
View 1 Replies
About a week ago my 2002 santa fe suddenly lacked performance and the check engine light came on . At the same time I noticed the speedometer stopped registering. I later discovered the poor performance was due to the fact that the vehicle was in 3rd gear "limp" mode. The code generated is 1602 "failure to communicate between the ecu and transmission control module". At this point I hoping its just a faulty speed sensor that's causing the problem and not the transmission control module.
Does it indeed sound like a bad speed sensor or does it sound like a faulty TCM or could it be a break in the wires between the ECU and TCM? Also, is it safe to drive the vehicle in limp mode until i replace the part later this week?
View 8 Replies
I have a Korean spec 2014 Hyundai Santa Fe 2.2L R-eVGT 6AT 4WD. Around a year ago it started to go into limp mode i had it checked and the error code was p0488 (EGR) Throttle Control Circuit A Range / Performance.
It has gradually become more frequent to the extent it goes into limp mode within a a minute or so . so far the dealer has changed the EGR valve, TCM , the whole turbo assembly and it is no different. They have also stripped and cleaned the intake manifold and egr cooler.
View 6 Replies
I have been having trouble with the shift solenoid and the trans going into limp mode. I recently replaced the shift solenoid and I now have the same problem but just when the temp outside is above 90 F or when I sit in traffic or idle for more than 3 or 4 minutes. The same code p0758 comes back up. I was thinking maybe the temp sensor?
View 2 Replies
My tranny is stuck in limp mode. I can manually shift it, but it won't shift on it's own. The 'automatic' part of the automatic transimission is definitely not working right.
I searched and checked for the usual suspects, low battery or alternator output (measured over 14v at batt. when on), and the range selector switch. I removed the switch, took it apart, cleaned it up, and reinstalled it. It looked like it was in decent shape inside, although it appeared to have had a bit of oil of some sort that had leaked into it. There was a bit of oil on that side of the tranny, around the gear selector and switch, but not enough to actually drip as I don't have any stains on my driveway where I always park. The only thing I haven't checked is the atf fluid level, as I can't seem to find the my wrench that will take off the fill nut. I'll get that figured out tonight.
The tranny hasn't been taken care of like it should, I've had the fluid replaced two or three times over 100k of ownership, but I'm not sure about the filter. Would the need for a filter and fluid change cause it to go into limp mode? Also, it's not throwing any CEL codes either.
View 14 Replies
We have a 2006 Passat, 30K miles, live in northeast on a Great Lake. We bought it used in 5/07 with 11K miles on it. The other day, a whole mess of warning lights came on, and the car went into "limp mode." The dealership diagnosed corroded wires where they connect to the throttle valve controller. We usually keep our cars for years, and we've never had corroded wires before. Is this a typical problem of VW's? The service mgr said he'd seen about 6 come in in the last year, but I don't know if that's a lot or a few compared to other brands. We're getting ready to shop for cars again, and we'd consider a new Jetta, but not if it can't go out in the rain. Also, if the wires corroded once, what will keep them from corroding again? Should we expect this to keep happening?
View 2 Replies
My transmission control module has gone bad, resulting in the car being in"limp" mode. I am advised not to drive the car in this condition as it starts out in 3rd and the transmission will be damaged. Thus far, my local dealer has, on a preliminary basis, been advised that there are none of these parts available anywhere in the world according to the computer and VW may have to manufacture one. This does not sound possible. Meanwhile, the dealer says no rental car will be offered so I am contacting VW North America to escalate. It could be up to a month to get a new part. Meanwhile, the car is in the garage just sitting.
View 7 Replies
So yesterday, this had happened for the third time in 3 years owning this car. Unhooking the battery for 20-30 minutes resets the computer and it is ready to go for a while with no issues. This has become annoying though. What is causing the car to enter "limp" mode and stay in third gear? One time it happened, I brought it to AutoZone and they did a scan and came up with the speed sensor. I haven't replaced it because it didn't happen for a while after that.
View 11 Replies
Turn air conditioner on transmission goes into limp mode??
1999 ranger 2 door 2,5 engine long wheel base,,auto trans.
2wd no power windows no power seats....
View 12 Replies
I have a 2008 ISF with a k&n intake and QTP exhaust cutouts. About a month ago my car died on me and when I restarted it, the car went into limp mode. The "check vsc" light is on along with the traction light and CEL. I took it to my mechanic and he said I needed to replace the MAF sensor and I did. 100 miles later the car went into limp mode again. So I took it to a mechanic that knows Lexus vehicles very well apparently, and he diagnosed it to be my intake. So he replaced it with the stock intake. Now I've driven another 100 miles and the problem has come back again. The car is throwing all kinds of codes when I connect the obd2 scanner to it.
It is throwing p0031, p0037, p0051, p0057, p0102, p1360, p1361, and a whole bunch more.
View 14 Replies
I have an issue with my 2004 2.7 Santa Fe. I keep getting fault codes P0335 and P1372, the engine then goes into limp mode and is very hard to start.
So far I have replaced the crankshaft position sensor, the MAF sensor, the spark plugs, new ignition coils and leads.
I have traced the wiring and found no shorts, the only thing which does not match the service manual is that I get 5v on the CKPS sensor wire when the ignition is on, it said it should be 0V.
The car can sometimes run for 50+miles with no issues - then stalls with codes P0335 and P1372. I have a feeling its worse when the aircon is on but cant be 100% certain/
View 16 Replies
