Santa FE SM (2001-06) :: V6 Showing Error Code P2100 - ETS Relay?
Nov 6, 2014
My Hyundai Santa Fe 2006 V6 3.5L shows error code P2100. I cannot for the life of me find the ETS relay. Ive scoured the net but just found vague drawings and pics that didn't show ETS relay. I would also like to know is the ETS relay also known as the fail safe relay or is that a separate relay. Ive seen pics of the fail safe relay but none for the ETS relay. If there is such a relay, exactly where it is located?
View 2 Replies
Advertisement
I've checked the lines from the Purge Valve on the Passenger side of the Intake Manifold, Check OK
I've Checked that Valve OK
I've Replaced the Canister Close Valve
I've got the Gas Cap tight.
I've removed the rubber bushing holding the CCV to the Evap Canister, hoping to isolate the Filter and point the blame on it, no luck there!!
I'm thinking next is to drop the Tank and check over all the Goodies on top.... as much as I hate the thought of that, the two access holes under the seats, just don't allow access to enough of the tank!
any thing there that I could suspect, I see there's a check valve!
There's also the Fuel Tank Pressure Sensor, which may be at fault.
View 16 Replies
It seems that i'm most likely going to have to replace the entire plenum .
P1159 here are some details. [URL]..................
I've checked all connecting wires and none appear to be loose. When the issue started to occur and prior to discovering the P1159 code, I also replaced all coils. I replaced the coils because one was arching over to the metal of the engine. I assumed this may be my problem. The issue still persisted obviously. The check engine light never came on so I assumed I wouldn't get a code. I took it over to a friends house with a code reader and that's when I discovered that it was actually giving the P1159 code.
Are there any other model cars that utilize the same engine that I could use the plenum from? Getting this in working condition is going to be the difference in what I can get for it.
View 2 Replies
I have a 2003 diesel GS Santa Fe, every now and then when driving the ABS light comes on, not very often but it does, if I switch the ignition off and restart it goes out, I had it on a fault finder computer and it showed code c1274, I think its something to do with the G sensor and the way it breaks (ABS) is it an easy fault to fix? What are the costs involved and will it affect the driving of the car, like I say it rarely comes on and I don't notice any change in how it drives.
View 1 Replies
So the check engine sign came up on my car and using the OBD it tells me the error is P0113. After googling the information, it looks like I have an issue with IAT sensor.
I opened the air filter and what I believe what could be the sensor and there was nothing clogging up, so I'm assuming the sensor needs to be replaced
Question is where is the IAT sensor located and how do I dis-assemble it so I can replace it. Is it the piece that is located just before the air filter?
View 3 Replies
I just joined the forum mainly to care of my dads 2001 Hyundai Santa Fe but also I got a check engine light on my way home from work last night.
From last night I saw that oil was all over the timing belt. Today I inspected it with a Coworker and his OBD II reader.
Error Code was P0455, EVAP - Evaporative Emission Control System Leak Detected (gross leak).
Now the oil leak is stronger since the oil spills is on hood (inside hood). I will make a picture tonight when I get home.
I personal think it's leaking from a tube/ valve on top of the timing belt (picture will show more tonight). Thinking of cleaning the timing belt area, then drive a little around or leave it in idle to spot where the leak is from.
Common issue? I googled around but since P0455 is a common issue (on my 9-2x as well) I couldn't find anything about this I am also limited from my search since I am currently at my work PC incl. strong firewall.
I will see if google let me find a picture...
View 3 Replies
Engine light come on and everything is running great, this morning got this error code U0d00. Went to advanced auto and had them run a scan.
View 5 Replies
I got an Error Code of U0D00. What this is or means. The scan tool says to refer to your manual but I don't have one.
What the vehicle is doing is that it will work fine for a while then when you stop (in park) the engine will rev really high and back down all by it self for example. It will go up to 3.5 and back to 1 rpm repeated. Then when you start moving the car it will continue to idle higher like you are pressing the gas. During all of this the check engine light will appear?
View 3 Replies
I recently purchased a second-hand Prius T4 (2007 model) and I noticed that the red triangle exclamation was showing on the dashboard. Initially, my local mechanic found a P3000 error code and a B1801 error code.
I ran techstream on it just last night and the main errors that came out were:
Current codes:
Srs airbag B1801 - open circuit in driver side circuit
Air conditioner B1421
Transmission control - C2318
History codes:
HV battery - POA84
I also have just found out that this car was in a major collision in 2012. The air bag light is constantly on, along with the red triangle exclamation, on the dashboard. The fuses for the battery fan kit, horn, and air bag needed replacing (I think all three but definitely two of these).
View 19 Replies
Vehicle: 2003 Dodge Grand Caravan 3.3 Litre
I also have my CE light on. Hooked up my reader and got the "P1491 Radiator Fan Control Relay" code. I have checked my rad fan fuse and it is okay. My attempt to locate the rad fan relay took me from the rad fan wire to a device that looks like a heat sink. It is located on the vehicle frame between the rad. and front grill. Is this the rad fan relay? If it is I'm not sure how I would replace it. It seems riveted to the frame.
View 7 Replies
We have a '92 Pontiac Trans Sport with a 3.1L V6 TBI engine. Last Sunday evening it refused to start like someone left the transmission in Drive and the Park/Neutral switch was preventing it to start. There's the buzz sound from the fuel pump when you put the key on then nothing when you turn it to start the engine.
I checked the Park/Neutral swith by connecting an ALDL cable to the OBD port and it indicates correctly when I move the lever to Drive or Parking/Neutral. The only error code stored is "Fuel Pump Relay" but the Fuel Pump appear to be working?!
Battery is good, fuel pump fuse intact and the Park/Neutral switch appear to be working. How we can tackle this problem?
View 12 Replies
I replaced the blower relay around this time last year. I noticed this morning idling that the vents weren't blowing then when i was moving i heard it tick back on and would blow normally. This happens when driving too but more noticeable when idling. The AC light also flickers and goes on/off.
I can go ahead and replace it again but this seems to have gone through this brand new relay pretty fast. What I can fix to stop going through relays?
View 8 Replies
I am on vacation and the AC has stopped working in my '01 Prius. I have run the HVAC diagnostic and it shows the "21" code. The only thing I can find related to this code is the solar sensor fault. I have located the solar sensor on the dash but am not sure how to remove (to replace) it. I have gotten the little black cover off of it but don't know how the rest comes out. Does it just pull out or unscrew or do I have to squeeze some tabs or what?
View 2 Replies
I have a 2001 toyota prius with 130k miles on it. 4 days back the triangle of death showed up on the dash board. The car would run fine for 3-4 miles, then brake light (on the dashboard) would turn on.
Sometimes the car would run fine with the brake lights, other times it would really slow down. Turning the car off and then on again gives me another 3-4 miles before the same story repeats again.
This triangle of death used to appear earlier too(6-7 month back), stay for few hours and then magically disappear, but this time I m not so lucky.
View 5 Replies
I replaced blower switch last year a couple of years ago. I recently starting to get clicking noise from blower relay, and fan turns off then comes back on.
Question:
1- Problem more likely to be from the relay or the fan switch? Should I just replace the relay?
2- I can see and touch the fan relay, but how do I get to it to replace it? What dis-assembly is required?
View 1 Replies
Check engine light is on, when I went to get my car inspected it was showing an invalid vin code. How do get this off so I can get my emissions done?
2007 Santa Fe SE
View 3 Replies
I own an '01 Honda Accord LX with the ULEV engine and 178k on it. My CEL light came on about 6 months ago. Ran the scanner and it showed a P1457 (EVAP Leak). Waited until now when my inspection was due and expected it to be caused by the EVAP shut valve as I read that's often the cause of the problem with this code. Mechanic said that it can't pass inspection because of the OBD fail but that the diagnostic scanner showed everything functioning properly, including my assumption about the faulty shut valve.
He reset the code and said to drive it the 50 miles for the system to ready itself and bring it back in. As I've reset the code several times over the 6 months to see if it would self correct, I'm pretty confident it will come back on. My questions are, is it possible I've done damage to the onboard computer by not addressing the underlying problem 6 months ago? Are there emissions problems that are not checked by the diagnostic tool that the mechanic should be looking for?
View 7 Replies
I have a 2008 model 2.7 v6 with 80000 Km, and I would like to share my experience with several issues:
- Random misfire: brought the car to Hyundai, very bad response. I bought online the wiring of the spark plugs (according to them that was the reason of the misfire) and they installed it, did not improve. The car was still showing error code after clearing, and the fuel consumption at an average of 23L/100km.
- I then decided to change all the 6 spark plugs, no difference. The workshop told me the coils were in perfect condition. Still having a message like this: "ignition error on 2 or more spark plugs".
- I did a complete cleaning with contact spray of the MAF sensor.
- I bought online a couple of ignition coils, being original Hyundai ones, and changed them. When installing them i realized the existing ones were not original Hyundai and had a small marking, making me think they were recycled or chinese stuff.
- Having done that, the OBDII shown two more error codes: P341: error on camshaft position sensor, P2189: fuel idle (too much air, maybe caused by the first one). Changed both camshaft position sensors and then big change in the behaviour, more response, throttle, better gear switching.
- I so concluded that the 4 remaining coils have to be changed and ordered another time 4 of them online. OBDII showing now only one error code: random misfire. The engine going much better than all i got before.
- I have decided to take advantage of this order and also ordered a new TPS (seeing here that it was a common problem) and a Crankshaft position sensor (in order to prevent any other issue).
- I also changed previously 2 downstream o2 sensors that were giving an error related to emission. Emission here are not strictly controled so it is not a big issue.
My question is, what in all that sensors can more likely make my car burn 23L/100km??? Asian cities are quite similar to american cities, lots of highways. This consumption compared to what you describe is way over the normal one isn't it? I was assuming the ignition problem was the responsible, am i right?
View 54 Replies
I need to replace O2 Sensor which is Bank 2 Sensor 2 which needs to be replaced.
Where is this located on a 2009 Hyundai Santa Fe 3.3L
View 12 Replies
I have an issue in my car (Santa fe 2011) and it occurred since it was new (ODO 3000 KM , ESP light is on and the 4WD Blinking) . the agency could not resolve the issue. and my car up to now been in and out from the workshop for more than 6 times . and more the error code ( C1627 ) that appears in the GDS(Global Diagnostic System) does not exist in the system (troubleshoot manual) .
View 5 Replies
I have a Korean spec 2014 Hyundai Santa Fe 2.2L R-eVGT 6AT 4WD. Around a year ago it started to go into limp mode i had it checked and the error code was p0488 (EGR) Throttle Control Circuit A Range / Performance.
It has gradually become more frequent to the extent it goes into limp mode within a a minute or so . so far the dealer has changed the EGR valve, TCM , the whole turbo assembly and it is no different. They have also stripped and cleaned the intake manifold and egr cooler.
View 6 Replies
