Santa FE SM (2001-06) :: V6 3.6L Will Not Go In Reverse
Jan 24, 2014
My 2003 V6 3.6L has decided to not go into reverse today. My driveway is on a slope and the car is a few feet from the door so it is hard to tell if it goes into drive.
Obvious thought is that the tranny is gone. I would have thought that this would show signs before doing this as everything seemed fine last night.
Anything else that you can think of that I can look at? And if you are in the Reno/Sparks area, who do you take your car to for repair.
View 1 Replies
Advertisement
My son called me yesterday saying my 2005 Santa Fe 2.7 engine, 150,000 is having a problem.....car runs fine but when you put it into reverse it dies immediately. No check engine lights and I haven't checked for codes. I'll be getting home this afternoon.
2005 Santa FE
View 7 Replies
We have a 2001 Santa Fe. Very recently it began hesitating when put in gear going forward or reverse. Once the gas pedal is pressed, there's a delay of up to 2 seconds as RPM climbs, then the vehicle jerks into gear. It seems to run fine otherwise. Mileage is approx 128 k. Maintained very well by the same mechanic until very recently. Internet searches have gotten answers of use fuel additive, install some computer patch, fix an oxygen sensor, change tranny fluid and flush tranny, rebuild tranny.
View 2 Replies
I just did a motor swap on a 2003 with 3.5 auto tranny and awd. engine runs great and every thing is running fine. Only problem is that the trans will not create any power. With no drive shafts on it still wont move the splines. With that said the trans was driving/running great b4 the swap.
View 2 Replies
My 2003 Santa Fe makes a grumbling noise when first started, and put into drive or reverse. The noise seems to be coming from the passenger side of the engine compartment. The noise disappears when the drive train has warmed up.
View 4 Replies
2004 Santa Fe, clunking noise in drive or reverse. checked brakes and cv joints, replaced drivers front and still making the noise. Transfer case was a little low on fluid but not much. Put up on stands and turn wheels with no noise. Put in drive or reverse while in the air and rear wheels sit still. It is a 4wd so I would think that all 4 tires would be turning. While in the air the front both turn and no noise is made.
View 18 Replies
I recently bought a 2001 Sante Fe 4X4, (my first Hyundai), that has transmission issues. It has about 135,000 miles on it. It will start easily, and go into Reverse just fine, but would not move in any forward gears. It would occasionally shudder a bit when put in 'drive', but only move forward a few inches. Recently, my mechanic backed it around, then decided to try it in forward again. This time it went forward a couple hundred feet, then quit moving forward. Do I need a new transmission, and if so, what vehicles use this same transmission? Or is there a sensor or valve that could be defective?
View 5 Replies
Recently my 2004 Santa Fe 2.7 AWD (~86k miles) has started to give a sort of hard thump when shifting from reverse into drive. It's fine going into any other gears and it shifts up and down normally. If I shift from reverse to neutral and then to drive it's fine.
I changed the transmission fluid when we first got the car at 40K miles with Hyundai Liquid Unobtanium SPiii fluid and again at 80k miles with Valvoline's SPiii offering. I just checked the transmission fluid level and it's within the normal range.
I can't tell if this is just drive-line slop or something else inside the tranny.
View 2 Replies
2001 Santa Fe 2.7L 4wd ... In December I bought this vehicle it only has 95K on it. When I drove the car home I noticed it needed brakes so I put brand new pads and rotors on the whole way around. I changed the oil, air filter, wiper blades, and made sure all fluids were good. I had the front spring recall done and also put some new sway bar end links on the front. The car runs fine and I am rather impressed with it. It does have some rust but I'm not to worried about that. This isn't my everyday car just a winter/extra car. Recently I have been getting some clunking only when going from reverse to drive and going slow. You get a clunk..clunk pause clunk..clunk almost like you have a flat but once I get the car up to speed it is fine and you never hear it again until the car sits a day or so and then it will do it again. I don't know if I have a differential problem or a u joint or maybe something with the e brake or rear brakes? but it is -3 right now outside and I would rather know where to start so that when I can take a look at it I know some things to check or what it might be.
View 3 Replies
I have a 2002 santa fe 2.7. I just had the transmission rebuilt and since then have noticed a clunking sound when I shift into drive or reverse. It seems to be the lower motor mount is making noise from the motor moving the mount. I look at the mount and it appears to look good, but was wondering how I can really tell if a motor mount needs replacing or not.
View 3 Replies
Recently, my 2007 Santa Fe GLS (not AWD) has been experiencing a grinding noise coming from the rear of the vehicle while in reverse. What may be causing this?
View 9 Replies
I have a 2008 HYUNDAI SANTA FE 2.2 CRTD CDX MANUAL. It jumps when reversing, especially when turning in reverse. Is this normal or is there a fault?
View 4 Replies
This is the 4th time this has happened.While in reverse it will suddenly lock up as if I hit a large object,and the anti skid light will come on and also the all wheel drive light will come on.I will then shut off the engine and start the vehicle were the lights on dash will reset and go off.
View 7 Replies
I recently noticed that both reverse lights on my wife's 2010 Santa Fe are dead.
It's odd that both bulbs would burn out at the same time. So I checked them and they're both good. The bulbs are not burnt out.
What should I check next?
I looked up the fuses in the owner manual, checked those, and everything looks good there. There is a relay as well. I swapped that with a similar relay in the fuse box, but that made no difference either.
I suspect it's the reverse switch on the transmission. Ours is a manual transmission. How to locate and access that reverse switch?
View 12 Replies
I have Hyundai Santa Fe, 2009 (automatic). when I start engine in the morning everything is fine except the reverse gear. the reverse gear moves to position easily but the car does not move. After 5 minutes of starting engine, the reverse gear works again.
View 1 Replies
Here is what I have:
2009 Santa Fe 3.3L AWD
70k KMs / 43k Miles
Temp has been very cold, -20C / -4 F
Car starts up without any problems. Try to put car in Reverse and the shifter is very hard to move, if it moves at all. When I am able to get it into Reverse, I then try to put it in Drive and it does not "engage" the "D" and the car behaves like its in Neutral. Moving the shifter back to Park, Neutral, Drive is very difficult and sometimes it will not go into Park. The dash lights do not illuminate the selected P, R, N, D.
However, once the car is warmed up (no longer on C on the temperature gauge) I can with a little effort move the shifter freely (but more effort than it should take) and the car behaves normally. Gear shifts are smooth and in general it is operating normally.
The dash lights do illuminate the selected P, R, N, D. I've checked the Trans fluid level and it appears to be normal and was planning to change it this w-e but I'm no longer sure it will work. Even if it has never been changed.
Also note that I have recently changed a wheel/hub bearing due to a noise that sounds a lot like loud tires on a highway. The bearing change did not eliminate the noise and I assumed that I've changed the wrong one. The noise does not appear to be coming from the Trans, but I cant be 100% sure. The noise is speed related and occurs only after about 20KM/h 16MPH. Unsure if they are related..
View 3 Replies
Our 2009 Santa Fe AWD Limited shifts hard first thing in the morning when my wife shifts into reverse to back out of our parking space. This is a real hard THUD kind of shift, where the car jerks. After that, all shifting is normal. We don't have any other problems with the transmission when driving.
View 6 Replies
I started noticing that when I shift the car into reverse to back out of the driveway, the car door locks sound like they are trying to lock/unlock repeatedly for a couple of seconds. I know the car automatically locks the door when I shift out of park, but the multiple retries is a new behavior. All doors do lock. I do have the child locks enabled for the rear doors and that hasn't changed in 3-4 years. I also disabled them and the retries persist.
I have also noticed that around the same time (past month?) I must push the unlock button on the keyless entry remote twice to unlock all the doors--including the driver side door. In the past I only had to push the button once to just unlock the driver's door and the side lamps would flash, but one push doesn't do anything anymore. I've never changed the battery in the remote, but does the car care that the remote battery may be running low to exhibit this behavior? It's a 2010 SF with 52K miles.
View 5 Replies
I was driving my santa fe at 80 k's per hour when the revs started to climb towards 3500 thousand revs. I pulled of the road and stopped, I had noticed the engine light stuck on. then i lost drive and reverse, let it idle for 4 min and they come back. What's gone wrong with the car?
View 3 Replies
I was driving out of a parking lot and as I accelerated onto the main road my vehicle stopped. I heard a grinding sound and could not go forward or reverse. While the car is in drive, park or reverse my car will roll any which way. It pushed it across the street. I tried to locate my tranny dipstick via visual inspection and manual. I could not find it. Could the stick have never been put back at some point in service and caused this issue. That seems unlikely but the thought occurred. Could it be the velocity joint? Whatever it is it certainly sounds like a transmission issue.
View 1 Replies
I have santafe 3.5 2012 4WD , it's 51K on odometer, the problem when cold startup , Noise and small vibrate form front side , its look like from gears
When put to reverse (R) sound is louder and strong vibration from front side, all this problem gone when drive about 15 minutes.
I have visit 3 local shop they check the engine, gear box, everything normal, no check indicator appears.
View 5 Replies
