Santa FE SM (2001-06) :: Transmission Won't Move Car / RPMs Went Up
May 29, 2013
The other day I was driving my Santa Fe. I noticed the RPMs went up and then the car started slowing down, so I pulled over. Since then the car won't drive. Engine starts up but the car won't move at all. When I push the gas pedal I hear the engine revving, but no movement in drive or reverse. No check engine light, and I checked the transmission fluid, looks and smells good. I checked and it has no transmission pressure. I verified by removing the transmission cooler lines and shifted the truck in all gears. Nada. Could it be the filter, a sensor or the torque converter? Or am I looking at having to replace the whole transmission?
View 21 Replies
Advertisement
I just did a motor swap on a 2003 with 3.5 auto tranny and awd. engine runs great and every thing is running fine. Only problem is that the trans will not create any power. With no drive shafts on it still wont move the splines. With that said the trans was driving/running great b4 the swap.
View 2 Replies
I recently bought a 2001 Sante Fe 4X4, (my first Hyundai), that has transmission issues. It has about 135,000 miles on it. It will start easily, and go into Reverse just fine, but would not move in any forward gears. It would occasionally shudder a bit when put in 'drive', but only move forward a few inches. Recently, my mechanic backed it around, then decided to try it in forward again. This time it went forward a couple hundred feet, then quit moving forward. Do I need a new transmission, and if so, what vehicles use this same transmission? Or is there a sensor or valve that could be defective?
View 5 Replies
I have a 2002 Santa Fe V6. I'm getting the codes p1529, p0755, p0760, & p0765.
The car can start up & go, only for a short time. Engine will keep running, car won't move.
Kill the engine for 3 to 5 minutes, can start it up & go once again. Going 40mph increases the odds of the car not moving quicker.
View 4 Replies
I have a 2003 Santa Fe and it's been running fine except I just replaced my oil pan from damage from ice and just did front brake pads 2 days ago.( oil went onto the pads and caused a weird grinding sound) ...
After the brake pads were done it drove fine. I came home and the next morning I go to reverse and the truck will not move at all. I can go to any gear but it just will not move. I thought it could be the brakes were frozen because the front right was smoking after the pads were installed and had the guy who did them check it out. he figured it was a caliper on the driver's side and replaced it, but it will still not move. I am praying this is not a trans problem.
View 4 Replies
This morning as I get in to drive my kid to school (2005 2.7 2 wd auto) as I go to put it in reverse I noticeably have to pull it with some force. I have never had to "force it" before, it had always switched gears with ease. This time it felt very stiff but had no issues going into gear. After I dropped my son off at school I went through the gears up and down and it felt very stiff (at this point i have no issues with starting it or P).
At lunch I go out to get something to eat and when I go to start it up it won't start. I try and try and nothing. All the lights came on, it's not a battery issue at all (brand new). But after 10 tries it starts, so I'm pretty happy. Then I go to put it in gear (reverse) I can not press in the button on the side of the gear shift. It will not go in. I press with all my might and it wont budge. But again, after about 10 good tries at it goes in and I can then select my gear but still feels very stiff.
After stopping again I didn't shut off the engine and dicked around with the shifter basically figured out that my car is not recognizing Park. On the instrument panel each gear lights up but not P. It gets very stiff when trying to put it in P but it doesn't actually go into P. If I put it in P (or really the further up it will go) and shut off the car, it won't start again. I can start it up in N and only N.
View 9 Replies
I've got an 02 Santa Fe with the auto-dimming mirror. The tension that keeps the mirror in position has gotten loose, so the vibration from the road causes it to slowly move downward while driving.
Is there a way to tighten this up? Do I need to remove the mirror from the windshield to do this? (because, I can't even seem to figure out how to do that!)
View 2 Replies
My parents are having trouble with there 2008 Santa fe 3.3 L. The transmission won't shift and the rpm's climb really high. Does that mean the transmission is going or is it something else.
View 15 Replies
We have a 2006 Santa Fe Hyunda with 100,000 miles that when we hit 80 mph on the highway the rpms drop to zero and stay there. We just had the camshaft and crankshaft replaced. Why this is happening?"
View 3 Replies
This all started out when I wanted to change my original plugs that had 200k miles on them. I have that part done now and new wires. Then it wouldn't start without me starting it while holding the gas pedal down. Then I would have to press the pedal down or it would die.
I may need to clean the throttle body. I bought some Valvoline Throttle Body Cleaner and cleaned the throttle body it was black inside and now it's nice and clean. After that the car starts up fine except on the first try. It starts up and idles at around 2,000 rpms. When I press the brake it drops to 1,000, then back up to 2,000. The strangest part is I have no acceleration power now. I can press the pedal to the floor and it will only go to 3,000 rpms. It will slowly get faster as I drive but there's no immediate response when I press the pedal down.
Why would cleaning the throttle body do this? It throws a code when I first start it and it dies the P1110 code but I think that is because the rpms are at 600 when it catches it. No misfire codes or anything, so I think the plugs and wires are working. Just the faster than normal idle now and no power when I press the pedal down.
Would the throttle body cleaner hurt the throttle position sensor?
View 7 Replies
Earlier this week, noticed that my car was surging on its own; basically, if I came to a stop, I could still feel the engine, like it wanted to just take off. And if I would have taken my foot off the pedal, it would have done just that. Also, I knew the car had gas, but sometimes, when starting the car it would not start at all. I would have to wait about 5 minutes or so and add major gas to it with the pedal and then finally it would engage. And then the last thing was that when I would get to my destination and put it in Park, the RPMs would go up to about 1500 or so, maybe a bit higher and then stay there and go back down to about 1000, without me pressing on the gas pedal at all. So anyway, thought it was the throttle position sensor, so I had my Dad install a new one on the car. It was a pretty easy process and thought that took care of the problem.
The surging part basically stopped, so the new TPS took care of that, but then it still had problems with starting. Took it to a car repair place the next day and they changed out the spark plugs, said that they were causing a misfire in the engine. Also changed ignition wires and a new gasket. So after they were done, drove away and all seemed to be fine, but then went to the dentist and Parked and then the RPMs went up again. Tried to start it immediately afterwards and it wouldn't start again. Tried a few minutes later, added gas with the pedal and it did start. Took it back to the car repair place, they drove it around, inspected everything and everything checked out fine. (Yeah, of course!) Ok, so just thought maybe the repairs were taking a bit to take effect. But later in the day, wouldn't start again.
So next morning, took it to the Hyundai dealer. They looked at everything for about 2 hrs, and said that there was a vacuum hose that was leaking, so they put on a new clamp but everything else checked out okay. Ok, so now it starts fine every time, but today it did that high RPM thing again when I put it into Park. It doesn't do it every time, but the RPM will just go up randomly then go back down and go back to normal. Should I clean the IAC with some type of carb cleaner to get out any carbon deposits? Or could it be a bad MAF sensor? Not sure what the symptoms are of that. Everything else seems to be okay now except for the random high RPMs when in Park and sometimes at startup too.
It's a 2 WD, V6 engine.
View 3 Replies
I have a 2001 Hyundai Santa Fe LX with 214,000 miles on it. In general, I am having two problems which are most likely related. I would like to get opinions on what is causing the problems, how to fix the problems, and what the cost might be for the fix. This is an older car and I don't want to bring it to a mechanic to just do searching.
1. RPMs fluctuate quickly at slower speeds in town stop and go traffic and while parking in Drive or Reverse. Fluctuation can be between 1000 to 2000 and 3000 RPMs back and forth.
2. Car stalls while sitting at stops when in Drive. When car stalls, RPMs have suddenly decreased to 0 (zero).
3. RPMs fluctuating and car stalling typically occur after I have made my first stop and have turned off the car.
There is also a Check Engine Light Code: P0304, Cylinder 4 Misfire Detected. I changed the vehicle speed sensor a few months ago.
Here are the details of what has been happening, when it happens, and what I have tried.
- When RPMs fluctuate, the car slowly accelerates and slows down and I can hear revving high and low. This happens when the RPMS fluctuate just a few RPMs around 1000 and when the RPMs are fluctuating up to higher RPMs.
- After the car has been driven for about 45 minutes and car is at slower speeds, RPMs will fall to zero while at stop and in Drive, and the RPM fluctuation will begin.
- RPMs jump to 2000 or 3000 and stay there but do not fluctuate when car is put in Park and Neutral.
- When car is in Park and at 2000 or 3000 RPMs, car takes a few extra seconds to turn off.
- Car accelerates without pressing gas pedal and will accelerate up to 40 mph.
- Car will sometimes lurch at slower speeds of 15, 25, and 35 mph when RPMs are fluctuating or when the gas pedal is pressed.
- When RPMs are fluctuating and at 1000 or higher and I am pressing the brake to slow down, the car fights in Drive and in Reverse.
- RPM fluctuation does not occur at interstate speeds.
- A couple days ago, when I was at interstate speeds of 60 to 75 mph and pressed the gas pedal, the car would stutter and jerk.
- RPM fluctuation and stalling primarily do not occur when the car is started at the beginning of the day or when the car has been off for several hours.
- Twice In the last week the RPM fluctuation and stalling occurred even after car was not started for several hours and after only about 5 to 10 minutes of driving in town stop and go traffic.
- Sometimes car stalls when I'm at a stop and slightly press the gas pedal to start driving.
- There are times in town traffic when the car is operating normally and is at 750 RPMs at stop, then the RPMs suddenly decreased from 750 to 0 (zero) and the car stalls.
- From Neutral, sometimes when I simultaneously put the car in Drive and press the gas pedal either by feathering or forcefully pressing pedal 3/4 to the floor, the car would have a delayed reaction to accelerate but would not shut off.
- After car has stalled, if I try to start it right away, the car cranks but does not start for about 5 minutes.
- The time between stalling and being able to get the car to turn back on has increased over time from starting up at first crank to not starting for 5 minutes.
- If I let the car sit for 3 to 5 minutes after it has stalled, the car starts up but takes a couple seconds to start while pumping the gas pedal.
- Issues have been happening since November but are getting more frequent.
- Stalling is happening more frequently and within minutes of each other.
View 10 Replies
Codes currently on ecm: P0134, P2125, P1174, P0735 My 2003 Santa Fe 2wd 3.5l with 160,000 miles was driving fine, then all the sudden whenever I reach about 3500 rpms there's a grinding noise that sounds like its coming from near or in the automatic transmission. As for the codes: P0134- I just replaced the o2 sensor with an oem part from autozone, so not sure why that's popping up. The connections look fine. P2125 and P1174- I'm trying to figure out whether the accelerator position sensor or throttle position sensor needs to be replaced. I have a multimeter but don't know if that will be able to tell me which one is out. The P0735 gear 5 incorrect ratio and grinding noise at 3500 rpms is what I am mostly worried about though. Could a transmission flush work with that?
View 2 Replies
2004 Santa fe. Having issues with RPM running high. When car is started, RPM sits at 1500 for a few mins, then drops to 500. Seems to be having issues either getting into gear or staying. At any mph, car seems to surge and not feel like it's getting either gas or power. While on cruise at 55+ mph, car will also surge with RPM dropping 500, then kicking back in. This goes on every few seconds up to random times.
Had it looked at this past weekend at a dealer, and of course it didn't do it one time, after doing it for a half hour prior on the interstate. Tech found no error codes when he checked it as well. Car was fine for an additional 300 miles, then it started again out of the blue. Pulled out at a red light and I though I was going to stall.
Just got laid off so I'm trying to eliminate before putting a lot of money into it if I don't have to. 132,000 miles.
View 2 Replies
2004 Santa Fe .... 2.7 6 Cyl 4WD 150k miles
Recently I started experiencing RPMs surging upon startup and driving before my engine warms up. The problem has gotten worse to where I push on the accelerator the RPMs jump to 2700 and the transmission feels like it disengages. My initial thought was the tranny was going bad and slipping. I checked the fluid level in the T and found it was maybe a half Qt. low. I topped it off, but this had no impact on the problem. On a side note, I am able to use the manual shifting feature on the "His and Hers" Shifter and drive the vehicle without any issue. Transmission works fine in manual. The surging RPMs which only occur in Automatic mode, triggered the CEL and I got a code of P0123 which is high side voltage on the Throttle Position Sensor. I replaced the gray TPS with a new black one.
Upon startup the RPMS jumped to 3000 just sitting in Park. I disassembled and reinstalled figuring I had something bound in the throttle. After reassembly the idle went up to 2200, still no good! I reinstalled the original gray TPS and the RPMs, upon starting, RPMs were 1500 with the old sensor...still too high. I did reset the ECU twice during the process of putting in the new sensor and reinstalling the old sensor. Right now I found that when I disconnect the TPS electrical connector, the engine runs normal. It starts right up with the TPS totally disconnected and idles at 750 RPMs! It will not shift to 2nd gear though, when I try to drive it in Automatic Mode. I can however drive in Manual Mode and drive normal and shift right through the gears. Who needs automatic mode right?!!!
View 4 Replies
My mother has a '04 Santa Fe 3.5. Her automobile makes a rattling/grinding sound when around 1000rpms/idle. However, the sound disappears when accelerating and drives like a charm. The sound returns once again around 1000rmps at idle or stop. I have changed the oil pan, replaced oil and filter and even put in a new battery. I'm not an aficionado when it comes to Hyundais (Subaru driver here).Car also has 180k miles.
View 6 Replies
I have a 2005 Santa Fe that for the last week or so has been slipping/jerking at about 2500rpms (2nd and 3rd gear). This only happens after the car has been warmed up and running for 20 minutes or so. I have put it into manual and it does not do this, only when in auto.
View 2 Replies
2004 2.4L 4cylinder manual transmission. I had a knock sensor code and replaced it. Then I had a code for the TPS and I replaced it with the new part today and after replacement the vehicle idles at 2000 RPM. what should I change?
View 5 Replies
I have a 2003 Santa Fe automatic transmission that sometimes will not shift out of 1st gear. Sometimes it works great. I took it to my local garage and he told me that it needed a transmission control module and to take it to the dealer. I took it to the dealer and they said nothing wrong with it at all. I brought it home and still some days it works great and some days will not shift out of 1st gear. What part needs replacement?
View 2 Replies
I have an 02 AWD 160k miles with a 2.7l V6. The car was driving fine then the transmission just stopped, no noise, no bucking just stopped as if it were shifted to neutral. Fluid is good, no codes. when the car is started and put into gear the RPM's drop as if its going to move but nothing.
View 7 Replies
Daughter bought 05' Santa Fe 4wd 3.5L, from original owner ,car has 47,000 miles on it, was maintained by dealer, and was obvious that car was well taken car of.
So first issue was throttle hesitation, which was mostly corrected by software update.
Now, transmission is acting goofy. If you step on gas heavily, it's as if the front wheels - or tranny -slip, then catch. Almost like a limited slip, then as it up shifts, you get a clunk. If it starts out in 2nd (I dont understand this ) then it's clunking going into 3rd.
If you are gently taking off, tranny acts normal. If you're cruising and punch it, it upshifts well, car goes nice.
Daughter called dealer who said update to throttle programming should have corrected any shift issues
So tech takes it out for ride, is able to get it to act up and states : issue in internal, and we need new tranny. 47,000 miles and need new tranny. Nice
I'm wondering if a fluid change and battery disconnect would work. Seems to me the the tech did a quick and dirty diagnosis.
View 3 Replies
