Santa FE SM (2001-06) :: Transmission Started Going Into Limp Mode And Causing Check Engine Light To Come On
Aug 23, 2016
2002 Santa Fe, 2.7 AWD
The transmission has started going into limp mode and causing the check engine light to come on.
The codes given are p0750 and.... I think p0751, for shift solenoids C and D. There is also the generic Transmission Control Module code.
Limp mode only occurs at higher speeds although shifting feels a little rough at times in lower speeds.
If operated in manual mode the vehicle can be driven normally at all speeds without going into limp mode.
Fluid levels are fine.
With limp mode occurring in automatic but not occurring in manual mode, is it more reasonable to believe the solenoids are malfunctioning or the control module itself? I'm inclined to replace the solenoids but find it odd that the vehicle operates normally in manual. Also, can the solenoids be replaced without removing the transmission? It looks like I could get the pan off but am unsure if there is room to get the work done once it is removed.
View 2 Replies
Advertisement
I have a 2005 2.7L Santa Fe that was shifting poorly and getting stuck in limp mode intermittently. I read up on it and found that it was probably an issue with the input/output speed sensors. The codes confirmed my suspicions and I replaced both the input and output sensors. The codes cleared and the tranny shifted like a dream. Unfortunately after 2 days and 100+ miles the car suddenly started down shifting randomly on my way home from work. The CEL came back on and the car went into limp mode. Could the sensor have gone bad again? Or could it be the wiring harness that plugs into one of the sensors? I don't understand why the car would be fine for a few days and then all of a sudden be acting the same way.
View 6 Replies
I have an issue with my 2004 2.7 Santa Fe. I keep getting fault codes P0335 and P1372, the engine then goes into limp mode and is very hard to start.
So far I have replaced the crankshaft position sensor, the MAF sensor, the spark plugs, new ignition coils and leads.
I have traced the wiring and found no shorts, the only thing which does not match the service manual is that I get 5v on the CKPS sensor wire when the ignition is on, it said it should be 0V.
The car can sometimes run for 50+miles with no issues - then stalls with codes P0335 and P1372. I have a feeling its worse when the aircon is on but cant be 100% certain/
View 16 Replies
Truck: 2009 F-150 Lariat SCrew 5.4 4x4 with 6.5" bed
For the last few years, I've had this intermittent problem where the service engine light (wrench icon) will pop on and the truck will go into limp home mode. While it's in this mode, all of the indicators on the dash freak out. Low fuel warning will come on, temperature warning, low battery voltage, etc. Turning the truck off and back on (sometimes a couple times) is enough to get it back to normal, albeit with a check engine light that needs to be cleared. It's happened infrequent enough that I've just been dealing with it. I got the codes a couple years back, but there wasn't much information available on what the potential causes might be. The Checker Auto parts database suggested one might be related to a wheel speed sensor.
Well, this afternoon it happened again, and I was near an O'Reilly, so I took it in to pull the codes. There were 9 total in the system; 5 of which were unique:
B0025
B00D5
U0073
U0100
U0253
They didn't have any information on what was causing them. What could be causing this. I'm getting sick of having to clear the check engine light and worry about the truck falling into limp home mode when I'm at intersections.
View 1 Replies
Bought a brand new F250 6.7 it has 7000 miles in it now and the check engine light comes on and the truck goes into limp mode. I have taken it in to the dealership twice they said there is no code they can find and they just reset the check engine light and it does ok for a bit then starts the cycle all over again. It also is only getting about 6.5 mpg....
View 6 Replies
I have been having a problem where the Santa Fe will drive great for a week, sometimes only a day and the engine light will come on and the car will go into limp mode. It will drop you from 65MPH to 10 MPH, if you put it in park the RPM's will race and stomping on the pedal will not affect the RPM's. After you turn it off for a couple of minutes it will drive ok again. I have replaced the Throttle Position Sensor and the Accelerator Pedal Sensor, cleaned all connections and checked wires in them. I have also cleaned the Throttle Body. The Dealer wants to replace the Throttle Body.
Had Engine Codes:
P0123 - Throttle Position Sensor 1 Signal Circuit High Imput
P1110 - Throttle Actuator Control System Malfuntion
P0222 - Throttle Position Sensor 2 Signal Circuit Low Imput
P1175 - Electric Throttle Valve Control System (ETS) Valve #
P1196 - Throttle Actuator Control System Limp Home-Stuck
View 3 Replies
I have a 2008 F350 with a 6.4 Powerstroke diesel engine that just experienced total engine failure. It has around 65K miles.
There is a heavy burn star pattern on all 8 pistons, a few pistons are cracked, a few cylinder walls are scored, glow plugs are melted, both heads are cracked with multiple stress fractures in each head.
About 1 month previously, the transmission would not work in tow mode and caused the engine to go into limp home mode. The dealership just replaced the entire tranny as a warranty item. About 1 week before the engine failure, I put in a 5.25 oz bottle of Lucas injector cleaner with a full tank of gas.
The Ford dealership is saying that the star pattern on all 8 pistons is due to high pressure fuel overspray and is evidence that I had a tuner on this engine and that the warranty is invalid. I did not have a tuner. What might have caused this engine failure?
Also, they only ripped down the top half of the motor, not the bottom half. I heard this might have been caused by a cracked crank shaft, but Ford refuses to investigate this possibility.
View 14 Replies
My wife has a 2006 santa fe 3.5l limited over the winter it started acting up went into limp mode and would only go 20mph so I went and picked up a TP sensor well it went out of limp mode so I never changed the sensor well last month it started doing it again so I changed it out didn't work!!! comes up with 2 codes sometimes p2110 and p2118 but normally its p2110 2 times.
If I hit the break it kinda bogs down and pulsates.i took it to my mechanic since I couldn't figure it out and with advice from a hyundai mech. He changed APS didn't fix it so we changed throttle body with used of course didn't work I checked wires and didn't fined any open circuits what are the chances that i got a bad APS or TPS...
View 3 Replies
I'm a little bit stuck here. This happened last night, and the dealer is closed today. I have a 2008 Santa Fe SE. It stalled last night, and when I turned it back on, I got a check engine light, the ESC light, and the AWD transmission light blinking. When I go to accelerate, it will not go passed 2000 RPM, and it is driving very sluggish. Its not knocking, or making any other kind of sounds. The air conditioning does not work, but the fan blows uncooled air. It accelerates extremely slowly, even with the petal mashed.
I plan on taking it in tomorrow, but I'd like to know if there is some way to reset the computer. I tried disconnecting the battery for about 30 minutes, but it didn't work.
View 2 Replies
About a week ago my 2002 santa fe suddenly lacked performance and the check engine light came on . At the same time I noticed the speedometer stopped registering. I later discovered the poor performance was due to the fact that the vehicle was in 3rd gear "limp" mode. The code generated is 1602 "failure to communicate between the ecu and transmission control module". At this point I hoping its just a faulty speed sensor that's causing the problem and not the transmission control module.
Does it indeed sound like a bad speed sensor or does it sound like a faulty TCM or could it be a break in the wires between the ECU and TCM? Also, is it safe to drive the vehicle in limp mode until i replace the part later this week?
View 8 Replies
I have a 2002 prius with 143,000 miles. On Friday, I went to start my car and put it in gear and the check engine light came on and the "triangle of death" lit up and car died. I turned it off and waited about 30 seconds and tried starting it again. It started and I drove 1/2mile home. Went into the garage and got the Actron/OBDII code reader. Pulled the code P3125 which when I googled it, it was referring to the inverter. I cleared the code and all was well.
View 6 Replies
I have a 2003 Dodge Intrepid SE 2.7L with 170,xxx miles.... My check engine light came on and is showing the codes P0562, P1776, P0871, P0441, P0700, and P0440. While driving, the car jerks and then i only have 2nd gear. If i shut the car off and turn it back on everything runs normal again for a little while. i had my battery and alternator checked and both tested good. What could be causing these codes and why only 2nd gear (Limp Mode)?
View 1 Replies
2001 Ranger 3.0 liter has developed a transmission casualty. I was driving along at 30 mph and the transmission went into "limp' mode with O/D light flashing and truck will only barely creep along with high engine rpm. When I got the truck home I was able to retrieve a p0720, output shaft speed sensor signal fault. I had hoped that replacing the sensor would solve this casualty.
Of course this was not the case. I have read all the posts I can find for this particular fault and realize that I must electrically trace the continuity of this circuit and also ensure that it's not grounded. I have been unable to find the needed wiring diagrams or pin out information.
Before I have to try and blindly start pawing through the connectors I'm looking for the pinout for the PCM and perhaps the bulk connector above the engine between the PCM and the transmission wiring harness. I am also keen to hear of any diagnostic tips that I may have overlooked.
View 10 Replies
I just got an Egde Evo which I installed and everything looked great. After a few runs, I noticed the ABS light coming on an soon after that my transmission goes to limp mode (the wrench lights up).
I receive the DTC error: P2106 on the Edge Evo.
I have gone back to Factory default, but it keeps coming back, ie. the ABS light lights up and the Trans goes to Forced Limited Power (according to the Evo).
View 6 Replies
Passat 2008/09 TSI engine 16k miles. APR stage 2+
I was driving normally and suddenly EPC light comes on, and the engine goes to limp mode. I turn the engine off and then turn on again. Everything runs fine. Vag shows N276 intermittent fail. I had already this fail, but always when starting engine, and the engine used to run OK. Is this a "sign" that is time to replace the HPFP? Or can I take the chance and keep running?
View 3 Replies
While I am driving the car it will start to die and skip. Happens randomly. Today I was driving up a small hill and it went quits on me started lurching with check engine light coming on and off. The car will turn over and start, but only for a few seconds before dying again.
Seems to happen when the car is running for a while. Also the ABS light flashes on then off randomly while driving sometimes although It hasn't been an issue. Will be checking tomorrow to see if it starts.
View 1 Replies
Went out to start my car today it had a rough time cranking over and when It started had a cel and in limp mode.
View 8 Replies
My 2007 Santa Fe was acting up at one time, then stopped doing it, and recently started again. My wife is the primary driver so I'm not always in the vehicle when it happens. When the vehicle is started cold, it will run a short distance then the MIL comes on and it goes to a 5 mph limp mode. After pulling over and shutting the vehicle completely down for a couple of minutes, it will run normally with the MIL still on. However, by the time I get back home to pull the codes, the MIL goes off. I don't remember the exact codes, but when it acted up last time I believe the codes had something to do with the TPS, Pedal Pos Sensor, and one other I can't remember.
View 3 Replies
My '04 santa fe 3.5 v6 gls/lx, 79k miles, gas, auto, check light has just come on while I was driving a less than 10 mile journey. How can I check what is wrong. Do I need some sort of diagnostic code checker. Do any national outlets check it for free (Pep Boys or Auto Zone, etc).
Just 5 days ago (about 50 miles only) I had timing belt, water pump, plugs and leads replaced, brakes checked and lubes flushed; BUT not at above dealers. I would rather know what the code is saying before I go back to the shop who carried out the work.
View 12 Replies
How can i turn off check engine light (hyundai santa fe 2003 3.5) by fuse ? I do not have any code scanner.
View 10 Replies
I recently purchased a 3.5 V6 Santa fe. The Check engine light keeps going on. I took it to a few shops and I am getting the same code. It is the O2 sensor in bank one. (I think the the code was po170.) The light keeps going on and off. All I can find are the same problems with different Santa Fe engines (2.7, etc. )... My SUV has 100,050 miles on it.
View 1 Replies
