Santa FE SM (2001-06) :: Stumble Or Surge On Light Acceleration
Jul 26, 2014
On light acceleration, it has a light stumble or surge and is very slow. On hard acceleration it makes a lot of noise, but isn't even fast enough. I can feel it shift through the gears, and can feel the converter lock up when it's supposed to. Any attempt to climb a slight hill or pass a car, it downshifts to what seems like 2 gears down, and has a loud roaring noise, but I don't feel the acceleration. At steady speed, it feels like it's hunting for a steady RPM, but can't find it.
I just had a timing belt replaced. Had the mech double check to make sure marks are correct. He did a cranking compression test and said they were all between 165-170 psi (is that a little high for a 150K mile car?). He smoke tested the intake system and found no leaks.
It does have codes stored for cat converter and a lean code-bank 1.
View 5 Replies
Advertisement
2003 2.4 base Santa Fe with 167k miles. It's having an intermittent stumble while idling and at take off once the engine is hot. I have replaced the plugs, coil pack, IAC, intake and cleaned MAF as well as replaced the PCV valve. Also checked and no vacuum hoses are misplaced or missing.
After some reading it appears it may be the EGR? I ordered it to replace just because I'm running out of things to try to replace without going to a shop.
View 5 Replies
My 2011 stick shift no air Accent has a hesitation or stumble on light acceleration that comes and goes. It may not occur for weeks then re-occurs. It is hard to reproduce intentionally. It never occurs in cruise. The CEL is not on. Most often occurs at 1400 to 1500 rpm with slight acceleration or a slight increase in load as coming to a slight hill. I tried injector cleaner a few times and changed air filter. It seemed more reloaded to induction airflow so I changed the MAP sensor. I understand the 2011 Accent does not have a MAF sensor. It is still occurring. It is fine in steady cruise as well as in hard acceleration. I am wondering if it is a TPS sensor problem. It has 60,000 miles and otherwise runs fine.
View 4 Replies
I recently picked up a 2000 Excursion with the 5.4 V8. Engine has 150,000. I got it cheap because it has a surging problem over 1500 RPM. This problem is intermittent.
I have 1 DTC. P1000 which is OBDII checks not complete. I cannot clear this even using the factory procedures. FYI..I have a snap on solus scanner. I think this is a voltage problem, If you try to start the engine with the scanner plugged in, the scanner shuts off, so I'm thinking the PCM loses battery power supply when the starter engages, resetting the PCM.
This problem is NOT a miss.... something isn't opening or shutting off above 1500 RPM. This truck doesn't have an EGR system, it has the EVAP system. This may be the problem, thats why I'm here. OK. heres a list of what I've replaced since I started working on it.
Engine oil and filter
air filter
fuel filter
8 COP's
8 plugs gapped properly
cam position sensor
IAC sensor
MAF sensor
Removed throttle body and cleaned.
Vacuum checks. 22" at purge valve,fuel dia, and vacuum canister
Checking with the scanner at 1500 RPM with problem
SFtrim1% bounces between5-15
SFtrim2% bounces between2-0
LFtrim1% bounces between11-13
LFtrim2% bounces between 5-6
O2S11(mv) bounces between 200-781
O2S21(mv) bounces between 200-800
Ssystem is in closed loop holding throttle at 1500 RPM... Note engine surges when at the RPM or above. I'm thinking the engine is lean, not sure how to read the trim numbers...
Idle is fine ... Problem is intermittent ... Also noticed that engine will only advance spark to 30 degrees @2000 RPM during this problem. I have seen it advance to 38-40 degrees when I do not have this problem, so I kind of understand the power loss,knock etc due to the timing, my question is whats causing it to do this?
EVAP question.... The purge valve should open according to PCM command a certain value, correct? I can monitor the duty cycle % but cannot activate and check proper duty cycle through scanner . When I try to I get an error message of module error -unspecified.
Disconnected hoses at purge valve,Full manifold vacumn on one, nothing on other, no flow through purge valve, but scanner shows 30% duty cycle. I would think the should be a little flow at 30% Maybe my problem? Troubleshoot procedure for the EVAP would be good.
View 14 Replies
So my 2005 elantra 2.0 CVVT has 189k on it 1 owner.
I got a check engine light one day and i read the code. Came out to be 02 sensor code bank 1. So i order a denso o2 sensor and replace the part.
I drive the car for about 400 miles to reset monitors and get a check engine light. P0420 cat code. At this point the car drives with normal power and pickup.
1000 miles later my car has lost power. It doesn't have any get up or power when driving normally. I take the car to my local shop and they recommend replacing front cat. I replace front cat, same issue.
At this point i'm not sure if it is a transmission problem or maybe my 2nd cat or something else?
On the freeway if I put my pedal to the ground the rpms surge up very very slowly,
Also seems like the car doesn't shift till around 4k rpms, seems like previously it shifted sooner.
View 10 Replies
Once warmed up, while sitting at a stop in Drive, there is what feels like an engine stumble every so often. Good guess is every 45-60 seconds, so it only happens once, maybe twice at long stops. There is a sudden change in pitch the engine, and the car - for lack of a better term - shudders. The thing I have noticed is that when it does this there is no indication anything has happened with the tachometer - RPMs hold perfectly steady. Additionally, there is no shudder when sitting in park or neutral, only drive.
I initially thought it might be an ignition fault, so when I replaced the balance shaft belt I also replaced the crank sensor. No change in behavior. I did some googling, which suggested the issue might be related to the EGR not closing properly. I changed all the vacuum hoses and removed the switching solenoid to test - it seems to be doing its job. I have not removed or inspected the EGR valve itself. However, because there is no symptom in engine speed and the sensation doesn't happen in park or neutral and only happens when warm, I am starting to suspect the transmission itself is the culprit - I can imagine if the torque converter quickly engaged and disengaged - and a little power made it to the wheels - the same result would happen.
There is nothing else odd about the engine or transmission. No codes. Runs like a top. Transmission always shifts perfectly. Fluid was changed two years ago, about 15,000 miles. What came out looked good as well. I'm okay with replacing EGR components, but I don't want to throw money at the problem unnecessarily. Maybe try driving around with the EGR vacuum hose pinched off or disconnected?
View 5 Replies
I recently noticed while driving my Santa fe the car started to stumble.Then a little while later the check engine light came on. Pulled the code came up with p300. It's a random misfire related code.
View 3 Replies
2004 Santa fe. Having issues with RPM running high. When car is started, RPM sits at 1500 for a few mins, then drops to 500. Seems to be having issues either getting into gear or staying. At any mph, car seems to surge and not feel like it's getting either gas or power. While on cruise at 55+ mph, car will also surge with RPM dropping 500, then kicking back in. This goes on every few seconds up to random times.
Had it looked at this past weekend at a dealer, and of course it didn't do it one time, after doing it for a half hour prior on the interstate. Tech found no error codes when he checked it as well. Car was fine for an additional 300 miles, then it started again out of the blue. Pulled out at a red light and I though I was going to stall.
Just got laid off so I'm trying to eliminate before putting a lot of money into it if I don't have to. 132,000 miles.
View 2 Replies
I have a Hyundai Santa fe 2004 6cyl 2.7 L , AWD. I am having problem of slow acceleration which is worse after a stop sign or red light. Sometimes while taking turns I feels like that I will not move and I was lucky to be not hit by a Car coming from opposite direction while taking a left turn today.
The Truck’s exhaust pipe broke recently and a auto garage welded it. But I am facing the above problem immediately after the repair of exhaust pipe. If I put more pressure on gas pedal then a mal function indicator comes and today I took it to another mechanic and he gets the error code of P0303 –engine misfire and wants to charge me ~ $600 $ to replace spark plugs and wires. The malfunction indicator goes off also while I am driving and can comes back after a while or a day. With the indicator on, the car drives erratic (minor jolts ) for few meters and then its fine. Since when I am driving on highways then I can go higher speeds without any problem. Is it still misfire issue???
View 11 Replies
So I was driving along at about 50 MPH and came to a normal stop for a red light. Sitting at the light for approximately 10 seconds and feel the engine stumble or possibly misfire.
I immediately look for any idiot lights and see none, however above the mileage range instead of the pages that are normally shown I see:
LIMIT --- MPH
I drove for about a mile and everything seemed fine, I pulled off into a lot and rebooted the car and now everything is back to normal.
View 6 Replies
My 2007 6.0 has a really rough (almost 'miss') during cold start up. After 5 seconds or so, it smooths back out and sounds normal. Until gauge reaches normal operating temp - there is a surge/lack of power during light acceleration. I also hear a frequent compressor coming on and running for a while which I am contributing to a possible vacuum leak. Maintenance is always done on time and I've already had a few costly repairs (both internally as well as externally) on the engine. I usually always wait for the glow-plug indicator to turn off before cranking the engine and let it idle for 5-10 minutes prior to driving it. Once the vehicle climbs to normal temp. everything seems to be fine but the compressor still comes back on every so often.IS it worth simply replacing the vacuum canister located behind the passenger side battery - or should I find someone to hook up a diagnostic unit first?
View 5 Replies
I just bought an 05' SE V6, with the 3.3 engine. Seemed to run good, had it checked by shop and they said it was a good buy, so i bought it. First day I owned it, took it to toyota dealership and had them do a 90, 000 mi service. did a timing belt, water pump, tranny flush, oil change. I got the car back, and it ran like crap! It would stumble on hard acceleration, and seem to even surge a bit at times. I took it right back? Service rep tried to say I put in diesel or bad gas. I only filled up with chevron premium, which is only gas i ever use. I know how to put gas in my tank!
Any how, they checked timing belt and said it was right, but the timing gear needed to be changed because one tooth looked rounded off. That didn't work either, still stumbled on acceleration, but idled perfect @ 675 rpms. So now the serv. manager gets involved, says he wants me satisfied. they then drained all my gas, then re-fill it. then flushed out all injectors. then put in all new plugs and PCV valve. I did a pressure test of fuel system, said it was good. While they were changing the plugs, they did a complete 6 cylinder compression test and scope analysis, and it came back good, too! I pick it up cause i got to go back. It ran a lot better but still stumbles on hard acceleration on highway. drove 1250 miles back, didn't use a drop of oil.
I did notice when I got 100 miles the temp gauge dropped all the way down to second mark on cold for a little bit, but went back to normal temp and stayed there through the last 1100 miles(that scared me, so i watched temp gauge like a hawk). And the outside temp was @ 62 degrees when the temp dropped at 1200 ft. Elevation...maybe it got stuck and is ok? My CEL has never came on through all this, and it does work, I have made sure of that.
I bought this car from original owner, and they had engine and heads just replaced in 2008 at 44,000 miles at toyota dealership under warranty fot 10,000 dollars. i verified this with that dealership 3 times with 3 different reps at that dealership. old owner said he was having problems with engine stumbling, and took it in twice and dealership said it was ok each time, not throwing any codes and sent him away saying car was ok.
View 2 Replies
It'll do okay when I am not flooring it, but when I do floor it there's a pretty noticeable lag and then VROM it'll take off like a bullet... This car has a manually operated throttle control, are there any adjustments I can make to make the truck more responsive? 2.4L 4Cyl....
View 3 Replies
My 2006 santa fe diesel 2.2 has started to be be a bit smokey when accelerating not even hard had the egr valve off today and gave it a good clean still the same it's not really bad but can see when moving off from parked...
View 2 Replies
What would cause a trouble code PO 300 on a 1998 Chevy Blazer. The truck will run good sometimes. When it runs bad it will stumble at low speed acceleration. It will run fine wide open. Dealer looked at it and thought it was egr vale. I replaced it and it runs a little better but still stumbles.
View 5 Replies
I have a 97 F150 4.6. The truck has developed a slight stumble/misfire when under acceleration. Once at speed it runs fine. It has not given any codes. I've checked for them several times. The plugs and wires have been changed. Is it possible that a coil pack could be bad without throwing a code?
View 3 Replies
2002 Santa Fe 2.7L AWD automatic
She was on the highway this afternoon and was accelerating to merge in with traffic. Apparently the car just reved up without actually accelerating. She said it felt like she was in neutral. I've driven the car a few times over the last week and it has been running perfectly - No hesitation anywhere at any speed. There are no CELs (yet). It is probably worth mentioning that it has been raining HEAVILY here for the last 24-hours and I would not be the least bit surprised if she hit a few puddles on the way. I can just about guarantee the CPS has never been changed and am suspecting it may be a short in causing her problem.
View 4 Replies
I just bought a used 2004 3.5l automatic Santa Fe. The vibration is most noticeable from 35 - 40mph during acceleration and deceleration. It's there at higher speeds but the car doesn't physically vibrate as much.
The vibration is there with the car coasting and transmission in neutral. It's there with the car coasting and the motor off.
The tires and wheels have been swapped out with other wheels and tires. No change.
The front driveshaft U-joint has been replaced. No change.
It seems to be in the drivetrain somewhere. I would like to fix it without slowly replacing everything.
View 6 Replies
So this happens fairly regularly. only during part throttle, cruising, the acceleration and rpm will dip and fall for a second, then comes back. if i let off the gas when it happens and get back on it, it comes back sooner. about a year ago i got TPS CEL, changed the APS but it didn't fix anything.
Weird thing is, when using cruise i don't see it. at least it's not nearly as noticeable. I had some idle and misfire issues recently and found a broken coil the culprit. changed that out and fixed those issues.
What would cause this issue when using the pedal but not the cruise? I think it has something to do with the accelerator pedal sensor...i do notice the throttle cable going to the APS has a small nut on it and it looks like it can be adjusted, would that cause this issue? research says TPS doesn't fail....
View 7 Replies
When I accelerate from a stop or turn left/right with my 2006 Santa Fe, I receive a vibration which feels like a sliding motion or skidding over rough pavement. Have just recently switched my tires from winter to summer and have had them balanced and aligned twice with no change in the problem.
View 2 Replies
I have a 2000 Tahoe with the 5.3L V-8, 351,000 (yes that is correct) miles. Runs great except it has recently developed a stutter, hesitation, skip, I don't really know how to describe it, under acceleration or at steady speed. This is an intermittent problem and it is driving me batty. The only codes are a P0420, maybe after 350k miles it needs replaced? Would that possibly cause this issue, or am I looking at something more sinister?
View 2 Replies
