Santa FE SM (2001-06) :: Small Clunking Noises In Front End At Low Speeds?
Apr 4, 2013
I figured out what was causing my small clunking noises in the front end.. They were faint, but you could hear them at low speeds..
Front sway bar bushes and end links.. Replaced mine with auto7 bushes and moog endlinks.. They didnt "feel" loose or wobbled but replacing these parts got rid of my clunks..
Only downside was the bushes are really hard to replace, need to remove the rack, subframe, etc..
My car has about 150k miles, and the bushes were a little oval..
View 8 Replies
Advertisement
I recently had my manual transmission go out on my 2002 Elantra GLS. It has 208k miles and the tranny had been giving me shifting issues for years. It finally made some clunking and whining noises at certain speeds. I picked up a replacement tranny, but the car has sat in my garage for the last two months. I slowly worked on it over that time and have finally completed it. I went to start it up tonight and it idles normally for 1 second, then it revs up to about 5k. It does this over and over until I turn the car off, and a very hard to see white-ish smoke comes from the air intake tube as I have it only partially on for testing.
The car ran fine before hand. What could this be? I have never experienced this with a vehicle before and searching on the web only gives me links to people having idling and revving issues while at stop lights or on the freeway. The idle did used to stick around 2.5k RPM when I started it up from time to time. Although, a small blip of the throttle would set it back to its normal idle speeds. BTW, the engine runs well with no knocks and has great compression across all 4 cylinders.
View 22 Replies
02 v6 awd my power steering cooler had a leak and was spraying fluid all over radiator. I replaced it and did a coolant flush new thermostat and a new temp sensor. Was still getting hot gauge was touching bottom of red. Did some looking my ac wasn't working for some reason the fuse was loose. I pushed it in and the big fan instantly kicked on high along with the ac. The small fan on the front of the condenser isn't running. Could this be my problem? When is it supposed to be running? I swapped the relays around with no change. I might take it apart tomorrow and hardware fan to see if it shot craps.
View 25 Replies
Posted a while back about a rattling/clunking noise coming from my front suspension. Since my car had nearly 100k miles on it and was still all stock, I went through and replaced ever single part of the front suspension. (Control arms, ball joints, got some Koni coil overs, strut mounts, sway bar end links, swar bar bushings). Turns out the noise wasn't actually related to the suspension. I've got massive play in both of my front axles. They make horrible rattling/clunking noises going over any sort of bump, even the REALLY small ones.
View 5 Replies
My 20th just recently started making clunking noises around the front left wheel area. It sounds like when I let off the gas it sounds like something is shifting forward... I don't think it is the engine mounts I'm wondering if its something with the suspension. The suspension is the stock 20th suspension.
View 4 Replies
My 2001 jeep cherokee sport had a transfer case boot replaced a few months ago where the "oil spinner?" is near the rear portion. Before that went out i had periodic noise that i narrowed down to the transfer case using a mechanics stethoscope. Now i have a cluncking noise with gear grinding sounds periodically between 15-35 mph. I have annecdotal evidence from another forum that it may be the oil pump in the transfere case related to a TSB, yet i cannot find this TSB. Am i on the right track? It appears that i can get an oil pump for $60 but i have to consider dropping the case myself and pulling it apart.
View 3 Replies
I'm getting ready to do some maintenance such as flushing the brake fluid, new air filter, and changing spark plugs. I've noticed lately a noise from what I'm assuming is my front suspension that can be heard when going over small bumps on roads at low speeds. It sound like a squeaky spring, almost like something needs to be oiled. I'm still on stock suspension with close to 80k on the clock, so I was wondering if there is anything in particular I should look for when I'm messing around the wheels bleeding brakes, or if there is a common procedure to lubricate something so the noise stops. I can hear it from inside the cabin so I imagine you can hear it from outside the car.
View 3 Replies
This just started happening on the driver side. Going over bumps and slight road wobble type imperfections make a medium pitched clunk sound. The sound stops as soon as I press the brakes ( which I just replaced last week). I do have a worn out bushing on the curved lower control arm. Could that be it? Do I need to replace all control arms or can I do just the curved set? If thats the issue.
View 13 Replies
2010 chevrolet HHR clunking from front suspension, rough road, slow speeds. Is this typical of worn sway bar bushings or something more expensive?
View 1 Replies
05 Santa Fe GLS 2.7L, auto, 2WD, 161K miles. Just bought it a couple weeks ago. Not much info about repair history, other than it appears to be well maintained inside and out.
Engine makes two kinds of noise - rattly top end noise and a low frequency thud-thud-thud.
I have shared some MP3 files on my Google Drive, but the forum blocks links for new users.
Apart from the noises, the engine starts and runs flawlessly, seems to have plenty of power (for a 2.7L, ha), and cruises at freeway speeds no problem. No tailpipe smoke or steam, whether cold or hot. Have searched the forums for this but nothing matches exactly.
I don't drive it much because I work from home, basically just around the corner to the grocery store and back. Haven't pulled the valve or timing covers yet, waiting to hear from all you Hyundai experts out there. Top end noise is one thing, but the thud really has me concerned.
Top end noise sounds like lifters not injectors - but I'm not sure I can really tell the difference, there's a lot of "sewing machine noise" going on. On cold start, it's not very noticeable, but becomes more pronounced as the the engine warms up. At operating temp it settles into a consistent rattle at idle. Seems to diminish slightly with higher RPMs, which also suggests worn/sticky lifters.
Oil looks clean and fresh. Haven't tried the Hyundai oil filter, but IMO this level of noise is well beyond the simple lifter ticking that others in the forums have described and reported cured by using the OEM filter.
I used the "long screwdriver with handle in my ear" trick to listen at various points on the heads and valve covers. At idle, it sounds like 2 or 3 lifters on the front bank that are making most of the noise, but maybe a couple on the rear bank as well, hard to get the screwdriver tip back there. Is there a particular spot where lifters can be heard best, distinct from everything else?
The low frequency thud-thud-thud is most audible when letting the throttle close after opening it up to about 2000 rpm. It can also be strongly felt through the throttle mechanism when operating it by hand. Still audible at higher RPMs, but not nearly as distinct, more of a subdued throbbing. Noise is coming from around the rear bank, about half way down the firewall. I fear it is number 3 rod, but is there anything else that would make this sound? I don't think it's a motor mount because there's no noise when putting it into gear, driving, or shifting. How can I tell for sure whether it's a rod? If it is a rod, can it be replaced without pulling the motor?
View 10 Replies
I've been told that the 2002 Santa Fe that I drive has a small leak in the head gasket and that this will be a major problem for the A/C compressor in the not-too-distant future. Supposedly the compressor is located below where the leak is and that over time (5-6 months) this can/will cause the compressor to need to be replaced. Does this seem like a credible scenario?
View 2 Replies
Daughter bought 05' Santa Fe 4wd 3.5L, from original owner ,car has 47,000 miles on it, was maintained by dealer, and was obvious that car was well taken car of.
So first issue was throttle hesitation, which was mostly corrected by software update.
Now, transmission is acting goofy. If you step on gas heavily, it's as if the front wheels - or tranny -slip, then catch. Almost like a limited slip, then as it up shifts, you get a clunk. If it starts out in 2nd (I dont understand this ) then it's clunking going into 3rd.
If you are gently taking off, tranny acts normal. If you're cruising and punch it, it upshifts well, car goes nice.
Daughter called dealer who said update to throttle programming should have corrected any shift issues
So tech takes it out for ride, is able to get it to act up and states : issue in internal, and we need new tranny. 47,000 miles and need new tranny. Nice
I'm wondering if a fluid change and battery disconnect would work. Seems to me the the tech did a quick and dirty diagnosis.
View 3 Replies
My son's 2001 Prius (Gen I) has squeaky noises in the front end. When I had the two front tires replaced yesterday, I asked them to see if they could diagnose the problem and he said he thought it could be the control arm because he had had the same noise in his Toyota Camry and that was what it was.
View 1 Replies
I can't find the obd port on my new 2007 SF. Also there is a clunking coming from the front suspension when i go over bumps, what is the most common cause of this?
View 13 Replies
Last summer my 04 SantaFe (140,000 mi, automatic) would feel like it was sticking and bumping when backing out of a parking space, then after shifting into Drive it would jerk and then make a huge thunking noise when applying the gas pedal. However, this would only happen sometimes, not all the time, and was not dependent upon the weather, surface, whether it had just been driven or not, etc. It would just happen when it happened. I brought it to the Hyundai garage and they replaced an axle and sensor. I continued having the same problem, brought it back to the garage and they replaced the viscous coupler.
I continued to experience the same problem after that, brought it back to the garage and they had the car for 10 days. I was told they had to get a mechanic in who was familiar working on 04 Santa Fe's and they determined the axle they replaced was bad, so they put in a new one. Everything ran great until I brought the car in early February for an "off balance ceiling fan" noise when accelerating. I brought the car to the Hyundai garage again and had the transfer case replaced.
Now the "clunking/grinding" is back when moving from R to D!!! So I brought it back to the garage again Monday and they said they cannot find anything wrong, and they are convinced it's just a symptom of the age and mileage of the car. However, it happened again today, but worse than ever before. This time it felt like it might not even move from R to D, and then it continued the grinding and bumping after accelerating and then the car felt "sluggish". I am convinced something is really wrong, although they assured me at the garage that the transmission is good, the axle, sensor and boot are all good etc. What else could it be?
View 1 Replies
2004 Santa Fe, clunking noise in drive or reverse. checked brakes and cv joints, replaced drivers front and still making the noise. Transfer case was a little low on fluid but not much. Put up on stands and turn wheels with no noise. Put in drive or reverse while in the air and rear wheels sit still. It is a 4wd so I would think that all 4 tires would be turning. While in the air the front both turn and no noise is made.
View 18 Replies
I'm trying to figure out a small leak on my mothers' Santa Fe. Recently I smelled coolant after my mother had gone for a long drive. I checked the Radiator and overflow... need maybe 1 qt of coolant.
Now I'm trying to find the cause of the missing coolant ! While it's running, I see no leak. Shut it off and it starts to drip from a small plastic tube on the firewall inside the engine bay area (on the passenger side). It drips down onto a rubber boot covering some steering stuff. Is this from the heater core?
View 4 Replies
2001 Santa Fe 2.7L 4wd ... In December I bought this vehicle it only has 95K on it. When I drove the car home I noticed it needed brakes so I put brand new pads and rotors on the whole way around. I changed the oil, air filter, wiper blades, and made sure all fluids were good. I had the front spring recall done and also put some new sway bar end links on the front. The car runs fine and I am rather impressed with it. It does have some rust but I'm not to worried about that. This isn't my everyday car just a winter/extra car. Recently I have been getting some clunking only when going from reverse to drive and going slow. You get a clunk..clunk pause clunk..clunk almost like you have a flat but once I get the car up to speed it is fine and you never hear it again until the car sits a day or so and then it will do it again. I don't know if I have a differential problem or a u joint or maybe something with the e brake or rear brakes? but it is -3 right now outside and I would rather know where to start so that when I can take a look at it I know some things to check or what it might be.
View 3 Replies
I have a 2002 santa fe 2.7. I just had the transmission rebuilt and since then have noticed a clunking sound when I shift into drive or reverse. It seems to be the lower motor mount is making noise from the motor moving the mount. I look at the mount and it appears to look good, but was wondering how I can really tell if a motor mount needs replacing or not.
View 3 Replies
I have a 2001 f250 4x4 about 4 months ago I replaced my pass. side front wheel bearing unit and here recently about 3 to 4 weeks ago I get a grinding/ rubbing sound when ever I turn right it gets louder the harder the right turn I do not seem to notice it as much moving at speed but driving through parking lots and slow speed right turns I can hear it. I have checked everything and nothing is loose and I can not see any signs or fresh rub marks on anything. I am getting to the point of just buying a new unit and replacing the one I just replaced. What my problem could be?
View 3 Replies
I had to replace a seized caliper last month on front driver side. Replacement went without a hitch. However I recently noticed pulling to the left pretty severe on the driver side. Also at speeds between 5 and 15 MPH I hear chatter from the front end.
*Every boot on the suspension is in good shape.
*Nothing rubbing against the rotor
*Chatter does not occur when turning the wheel
* Feel some play pulling from 10 and 3 on the tire
* Tires up in the air and spinning I don't hear any chatter
* Stabilizers are tight and sound
Im not good at diagnosing suspension, how to properly diagnose? Based on my prior experience with vehicles I am thinking Ball Joint in this case?
View 7 Replies
