I am beginning to get a rusty colored leak at the interface between the transfer case and transaxle on my 2003 Santa Fe 2.7l 4wd. There wasn't any leak less than a week ago. What would make the transaxle and transfer case start leaking at the same time?
View 3 RepliesWell, I have the dreaded transfer case leak on my 112000 mile 03 2.7 santa fe. I have just returned from a 12,000 mile trip through Canada, Alaska and then back to Colorado. During that trip I was smelling a burning oil smell and after I came back I traced it to the transfer case. I think it is leaking both from where it mates to the drive train and a one inch seam along the transfer case plate.
It has leaked there for some time(and I had been diligent about filling it up), but this extended trip it has has been more bothersome. I called the local Hyundai shop and they want $1100 and won't guarantee a fix. Is there some product I could use on that one inch seam externally to stop the leak (I know that wouldn't seal the circular seam around the drive shaft)? I kept very accurate gas records and averaged 25.6 MPG for the whole 12k trip running from 55 to 65 MPH.
The dang thing leaks from the fill plug, I been reading about using liquid teflon on it.
View 4 RepliesI have a 03 Excursion 6.0 that just developed a transmission leak between the transmission and transfer case. It appears to be the transmission because the transfer case fluid is at the top. I started to notice transmission fluid leaking in my driveway. I have not had any driving issues with the transmission but I am not driving until I correct the problem. If this is the rear transmission seal, how had is it to change this seal? Must I remove the spacer between the transfer case and 5r110 tranny? Any special tools needed?
My temps have stayed at or below 150 if I recall. My fluid is slightly low in the transmission at about 134 operating temperature. The fluid is clean, red and has no burnt odor. My transfer case is topped off. Fluid ran out the fill plug when I removed it.
There is an aluminum square spacer than necks down. It is about 6" long between the transmission output on the excursion and the transfer case. The leak I see is where that spacer meets the transfer case. I see enough for the fluid to leak onto the cross member and to the driveway. I estimate that I have lost less than a 1/2 quart of fluid over a couple weeks.
Made a short run to get lumber yesterday and when I got home the truck smelled hot I checked it out and found a transmission oil leak at the rear of the transmission in front of the transfer case. can not really see what is leaking only has 22,000 miles. What may have happen. 2011 F250 4x4 6.7....
View 14 Replies2001 F250, 7.3L ... After much diagnosis, I've found that the 4 positive feeds to the transfer case relay base have no power to them. The fuse that feeds them (#17 CJB) is fine and when I jump from the fuse hot side directly to the transfer case motor contacts on the relay base, it shifts fine. As far as I can tell, there is only one wire leading from that fuse so there must be a junction block somewhere that splits it into the 4 wires that feed the relay block. I've looked underneath and found nothing. How the 1 wire gets split into 4? On diagrams this junction point is labeled, but I don't know where to find that.
View 2 RepliesI have a 2001 Santa Fe 2.7l automatic. I recently changed out the automatic transmission (transaxle) as the old one had died. Now the starter motor plunger is not disengaging quick enough on start up and a screaming noise is made as flywheel turns as engine first turns over. I have just put a new starter motor in with exactly the same (screaming) result. The flywheel looks to be in reasonable condition as I inspected it when being put in, no teeth mangled and all teeth there. The transmission replacement was from a wrecked vehicle, I was told from same model vehicle but maybe a 2003 Santa Fe.
View 1 RepliesI purchased a 98 dodge ram 4x4 v8 with automatic transmission. When I purchased it the guy told me there was an issue with the transfer case. From what he told me he got stuck and the transfer case is the result. I was told there is a fork in the transfer case that is probably bent? Does this sound correct? It is currently in 2wd. Do I have to remove the transfer case to replace the fork? What is it like to remove the transfer case? Drop the tranny?
View 16 RepliesLooking at another Ex but the owner says the transfer case does not engage. Says it can be locked into 4X4 by crawling under it and engaging it manually by removing a motor [Servo motor ?] Does this mean I would need a new transfer case or just the servo motor ? I know mine did the same thing last winter. It would go into 4X4 and then pop out.
View 10 RepliesI just replaced the transfer case BW 4405. And I noticed that the 2 sensors (front drive shaft and rear drive shaft) are bad. What is the name of these two sensors? I'm looking for a brand new ones...
View 13 RepliesMy '99 Suburban 350 with the autotrac 4wd is having electrical problems. The transfer case fuse always blows. I thought it may be the transfer case shift motor, so I took it out and tried and the fuse still blew. I tested the pins on the fuse, and sure enough they are shorted together, but only when the car turns on.
View 14 RepliesI own a 2006 mazdaspeed 6 with 90k+ miles, 2 weeks ago I had a 90k service done at the dealership. On the 14th of May, the 90k service was done (which includes the changing the transfer case fluid/oil). Car was not driven every day, but on the 23rd of May the car made horrible noises on the way home from work. I called a flat bed/tow truck, and have tried to lock in the problem. The sound seems to be coming from the transfer case.The question is could they have done something wrong or was it just the transfer case’s time to go up?
View 19 RepliesTook it in for the 10K service and squeak that started coming from under the treg. The said it needs a new transfer case.
View 12 RepliesWhere/how to check the ATF in the transfer case? I found the lower drain bolt,but I don't see anything up higher that looks like a fill hole.
'91 Aerostar 4.0L AWD
2003 ex 6.0 limited....300000 miles ...Automatic.Merry Christmas to all.My Transfer case will not shift into 4wd . Dash light for 4wd high and low works .I get no power to transfer case 2pin connector when key turned on.Also fuses 19,27,31,33,34,45,111 are all good when checked with meter.I also swapped 2 relays in engine compartment and no change.4 WD Switch on dash has power on Green/red wire I think it is for dash light and not for operation.
View 13 RepliesSwapped out my transfer case since mine was detonated and now my tranny is running hotter? Drove in town for about 10-15 minutes and noticed my temps climbing and once it got to 180 it felt like it was slipping when moving from a full stop. i went home and parked it. Checked my fluid level and it looked a little low so topped it off while running and went through gears to make sure it was good. Drove again and it still went up to 180 in 10-15 minutes in town driving. Before we swapped the transfer case it was driving fine and went on a road trip 6 hour drive and felt fine. I bought the excursion and it supposedly had a new tranny in it.
View 14 RepliesSo long story short I have a 92 Aerostar AWD which I'm pretty sure had the transfer case recall done (97V204000 1992 FORD AEROSTAR Recalls) it has the aluminum driveshaft but a couple of years ago the transfer case cracked and I replaced it with a "New OEM" transfer case off eBay. Fast forward to the present and my van has a strong vibration at 60+ my transmission guy says it all looks good so the vibration has to be from one of the driveshafts. My thought is that I may have got a transfer case without the recall done on it and its warped my driveshaft. I don't really know thats possible or what I could do about it if that was the case.
View 8 RepliesI bought a new to me 03 explorer 4.6 tow package XLT 136000mi. Rebuilt aamco trans with 10k on it. Been checking it over before i put it on the road.. No 4x4 but the button lites work and i got into low range once. (Had a hell of a time getting back to high but eventually it did). Question is if there is 12v at the brown wire on the TC the case should be fully locked? I figure when i check it if there is not 12v at the brown wire in 4x4 high i could apply 12v directly with a jumper wire to see if the case locks to 4x4. Am I correct?
View 2 RepliesAbout 9 months ago heard a strange noise when shifted into 4 wd , sounded like driving over those grooves on the side of the highway to keep people awake.
Had to pull over to stop , as it would not go back into 2wd with the noise still going.
Then it stopped , after shutting truck off and restarting.
Then earlier this year after trying to do it again in 4wd had bad clunking noise and was hard to get back in 2wd , I can here the shift motor engaging and the dash reads in 4wd, seems its not engaging fully in 4wd and not going back to 2wd, its a very bad clunking noise, shakes the whole truck.
I had sold my Explorers but just picked up a 2000 Excursion V10 plow truck. It has been hacked and slashed I find cut wires under the dash and hood. I have tried everything to get the 4x4 to engage and no luck. It is used just for my driveway no road driving...
So question is: Can I engage the 4x4 at the transfer case so it will go, and stay in 4 wheel drive. If so do I take the shift motor off or does that big bolt by the motor do anything.
I keep getting a check engine wrench on the readout, put a scanner on it and got the following code:
P183b transfer case code ...
What this means?