2004 2.4L 4cylinder manual transmission. I had a knock sensor code and replaced it. Then I had a code for the TPS and I replaced it with the new part today and after replacement the vehicle idles at 2000 RPM. what should I change?
View 5 Repliesmy old lady has a 2001 olds intrigue with the 3.5L in it. Sunday evening we replaced the Throttle Position Sensor and the Coolant Temp Sensor. Monday she was on her way back to Iowa and the tempature gauge spiked up to the Hot area. I looked it over and could not find anything wrong. I sent her on her way and she made it about a mile before it did it again. The car will spike up to the hot area but the motor shows no signs of over heating. I checked the temps with a heat gun while the car is idling and read out Thermostat housing-160, Rad-80, Rad hose-130, and coolant 170. I than ran the car up so it shows on the gauge its hot and than checked again, it than reads Thermostat housing-172, Rad-100, Rad hose-134, and coolant 184. If I am running it at 1500 rpms it will spike up but once i take it up to 2500 rpms it drops back down to normal on the gauge. I am lost for what it could be.
View 19 RepliesWe bought a 2006 Hyundai Sante Fe with the 3.5L and 4 wheel drive about two months ago, it has 94,000 miles on it. It was purchased from a dealership, and they had to work on it for a month before we took it from them because of some lights that were on, resulting in some sensors being replaced. We had it about a month when we took it to the grocery store, when we came back out I started it and it made a terrible noise, but was running, I immediately turned it off. Upon further inspection, the main serpentine belt had snapped, causing some damage to the secondary belt. We towed it home and I began to fix the belts.
When I pulled off the passenger side wheel and access cover, I noticed the remains of the belt were stuck behind the harmonic balancer, I tugged on it with about 5 pounds of force, and the entire pulley fell off of the harmonic balancer. I'm not sure if the belt stacked up behind and pushed it off, or if it just went bad, but the rubber between the portion that connects to the crank and the pulley was ripped, and missing in some spots. I replaced the harmonic balancer, and both belts, good to go, everything is running fine.
About a week later, the TCS etc. lights came on, but no check engine. I researched it a bit and came up with three possibilities:
1. Fuse
2. Tone wheel cracked/broken
3. Crankshaft position sensor
I checked the fuses and nothing was burnt, I never lifted the truck up to check the tone wheels.
I have searched and have not found any information on replacing the throttle position sensor. My Santa Fe was running normal. I changed my tp sensor and how it limps along. When I loosened the old TPS, not even removed it, I heard a noise inside the TPS. When I replaced it I adjusted the TPS to read between 9 and 10% on my reader. But when I push on the gas pedal with the key on position the percentage doesn't move. Also when I drive it now it limps along and does not accelerate.
View 2 RepliesGetting code P2125. Read on here to get some electric contact cleaner and see if that works by cleaning the connections.
If I do end up changing out the Throttle Position Sensor, what voltage value do I look for when installing the new one ?
SO, my Buick has given the code for bad TPS, and it was replaced a little over a year ago...and now after the same symptoms, replaced again.. However, this time, right after replacing, it gave the code again, and still stalls out /doesn't want to stay running especially when put in gear. My regular mechanic also recently just put on a new catalytic converter and a new fuel pump and fuel filter. I'm at a loss, and desperately need my car back.
A little back history...about 3 years ago a 'friend' was to work on my car to install the thermostat and power washed the engine...which shortly after started having all kinds of electrical issues. Right after that, my mechanic had to install a coil, spark plugs, new ignition panel and the 1st tps.
Replacing the tps themselves? Is it something a newbie at diy car stuff can do? I'm getting codes P2016, P1295 and P161B, and I see no problem with the car except one thing, when the engine is cold the shift from P to D is rough. Is the tps causing this?
View 9 RepliesI was reading the car's settings using the Torque app and an OBDII bluetooth dongle and I realize that at WOT the ECU is only seeing 85% from the TPS. O know on some vehicles there is an actual procedure like turn the key forward, hold the gas pedal at WOT, turn the key all the way forward w/o starting while pulling the turn signal stalk down or something crazy like that to force the ECU to re-measure while you keep the gas pedal pinned to the floor. I know on other cars when it doesn't read a full 100% you miss out on a small amount of power and MPG so if it's an easy procedure with these cars I'd like to reset it. I did some searching but mostly came up with info on how to replace it and a few related subjects but noting on this specifically for this car specifically.
View 2 RepliesI just posted last week that my check engine light was on and the dealer wanted to replace fuel injectors. But after the fuel throttle was cleaned and oxygen sensor was replaced the check engine light went off. However, yesterday the check engine light came back on. I am talking it back to the dealer, in a couple of days. Where can I go to get to get the error codes read so I have them before I go back to the dealer? Around 128,000 runs fine, around 40 miles per gallon. Last time I had the oil change dealer nothing came up on the 30 point inspection.
View 7 RepliesAfter heavy rain yesterday my 2005 2.7 Santa fe wouldn't start today. Had it towed to nearby dealer. The crankshaft position sensor needs to be replaced. He claims its melted to the block and oil pan needs to be dropped to remove it.
View 5 RepliesMy check engine light came on the other day and the code stated the the "throttle position is open" so after researching and everyone telling me that i need to change the sensor. I did everything after was fine running better but today only after 3 days replacing it i get the same problems. car has no get up and go hardly can push to 20 mph and when in idle i press the break it starts to bog down and almost want to shut off! and can be really loud...
Santa fe 05' 3.5L ....
2002 My friend's 2.7L sante fe crankshaft position sensor went bad and I went to replace it. Removed bolt, it was stuck fast, tried to pry out and it broke off leaving the last 1/2 inch stuck in block. Tried drilling a hole in it and using a screw to get it out but no luck. Afraid to keep drilling that I might damage something behind it. How to get it out?
View 9 RepliesI've a 2.0L Santa Fe CRDI 4WD, 2003. My Crank position sensor has blown. My question is, does the timing belt have to be replaced with the sensor, or can the sensor be replaced alone? I know the belt must be replaced with petrol models but I've been told it may not be necessary with diesels.
View 1 Replies2004 Santa Fe .... 2.7 6 Cyl 4WD 150k miles
Recently I started experiencing RPMs surging upon startup and driving before my engine warms up. The problem has gotten worse to where I push on the accelerator the RPMs jump to 2700 and the transmission feels like it disengages. My initial thought was the tranny was going bad and slipping. I checked the fluid level in the T and found it was maybe a half Qt. low. I topped it off, but this had no impact on the problem. On a side note, I am able to use the manual shifting feature on the "His and Hers" Shifter and drive the vehicle without any issue. Transmission works fine in manual. The surging RPMs which only occur in Automatic mode, triggered the CEL and I got a code of P0123 which is high side voltage on the Throttle Position Sensor. I replaced the gray TPS with a new black one.
Upon startup the RPMS jumped to 3000 just sitting in Park. I disassembled and reinstalled figuring I had something bound in the throttle. After reassembly the idle went up to 2200, still no good! I reinstalled the original gray TPS and the RPMs, upon starting, RPMs were 1500 with the old sensor...still too high. I did reset the ECU twice during the process of putting in the new sensor and reinstalling the old sensor. Right now I found that when I disconnect the TPS electrical connector, the engine runs normal. It starts right up with the TPS totally disconnected and idles at 750 RPMs! It will not shift to 2nd gear though, when I try to drive it in Automatic Mode. I can however drive in Manual Mode and drive normal and shift right through the gears. Who needs automatic mode right?!!!
I am having a problem with my 2003 Santa Fe I have taken it to have the check engine light codes read and I have a code for the crankshaft position sensor, random misfires, something with gear 2 and 3 (not sure what it was exactly) it makes a loud noise when in 1st and 2nd gear when I shift out of 2nd the noise gets less and less until its gone and then does not come back until the car sits for a little while and cools down. Its running rough and does not have any power when accelerating. I had the timing belt changed a few weeks ago and it started running funny shortly after. I don't think the guy that did the timing belt knew what he was doing because I had to have someone go behind him and tighten the pulley.
View 3 RepliesCodes P0210 and P0733 for throttle sensor and third gear mismatch came in.
Dealer is going to replace throttle position sensor and said the Hangar Bearing is bad needing replacement.
I was just curious how long those jobs take to do roughly?
02 Santa Fe 2.4L/ automatic/2 WD. I replaced the fuel filter (only) and have had a nightmare ever since. It takes multiple tries to start, running a little longer each time. When it will finally stay running, only the most delicate of throttle feathering will allow any RPM's to be built up. Any attempt to do otherwise will result is sputtering, bucking and other unhealthy behaviors until the throttle is closed. It also gives off the smell of running rich.
I borrowed a scan tool and got P0136 and P0141, which I expect since the O2 sensor wiring was cut in two by the heat shield shortly after my daughter bout the vehicle. It also is giving me the P0340 Camshaft Position Sensor Circuit code. I had replaced the CMPS and its connector a couple of month ago. I replaced the sensor again to no avail. I have checked the Orange/Black wire from the connector to the ECM and it reads 0 ohms. I get battery voltage at the connector on the Blue supply wire but only get 1.86 to 2.0V when I check the signal with the engine running.
2004 VW R32, No engine mods. I did have the vacuum line sealed off for the flapper mod for about 3 months but is is now back to normal.
I've got the MIL, ESP, and EPC lights on and scanning codes as follows:
Code-P0222
Definition:
- Throttle pedal position (TPP) sensor/switch "B"
- Circuit Low
Explanation:
- Open or short circuit condition
Probable Cause:
- Poor Electrical Connection
- Faulty TPP sensor
- Faulty throttle valve control module
I don't know much about the situation but I took it to my friends shop first where we replaced the Throttle body, intake, and MAF. Didn't fix the problem so I took it to my local VW dealership and the tech's exact words were.."the codes coming up as a throttle pedal sensor. Is there perhaps a sensor by the pedal that I could check?
Am getting an EPC light + limp mode + code for accelerator position sensor (implausible signal). I have swapped out the pedal assembly, so it isn't the sensors themselves, and we've checked the wiring to the pedal assembly... I can feel in-car, and I can see via VAG-COM that one of the two sensors is basically toggling between a sensible % reading of pedal position at one moment, and then zero % the next, and of course every time the sensor reads zero, the ECU notes the error and cuts power... but this only happens when the steering wheel is straight or when turning to the right; I can drive around in a leftward circle all day and night without this occurring.
Why? What is there in the steering (either in the column or at the wheels, or basically any place in between) which, if malfunctioning, could affect the accelerator position sensors in one way or another (i.e. either through the normal operation of a safety system, or through a short or other electrical gremlin)?
The Problem: When I start my Ranger it dies right away, I do this about 10 times or so (worse when it is wet or has rained) then I can finally keep it running, by hitting the gas. Once I get it running it will cut out while driving as well. The idle is normal and if fires properly, I just took it in to the shop (non-dealer) and they said it fires normal and has normal fuel pressure, and the their computer returned no error codes. Their sugestion was replace the throttle position sensor. Do you all think this part could be the cause and where is the this sensor and is it hard to replace?
View 12 RepliesFord catalog does not list the TPS for a 1999 7.3 Super Duty as a separate replaceable part which leads to replacing the whole throttle pedal assembly. I found this to be incorrect. If you have a throttle pedal assembly with separate TPS (separate 3 wire connector) and IVS (Idle Validation Switch 2 wire connector) just the TPS can be replaced.
This is a pic of my 99 with new TPS installed : [URL] .....
Without removing the whole assembly you only need to remove the 2 T25 screws and the connector to replace.
Since this part is listed for more then 20 Ford trucks I figured it would work in my 99 7.3. I bought a brand new TPS from Pete (F250_) that he could not use. He has a 2002 with one 5 wire connector. It works perfectly in my 99. Not sure if it will work in a 2000 or 2001 but if the TPS and IVS each have their own connector it should. Make a visual inspection to be sure.
Part DY-967 or F4SZ-9B989-AA - Potentiometer
I was going to go with a Dorman TPS but like PartsGuyED likes to say "OEM Baby". The OEM TPS through Ed is actually cheaper then the Dorman.
Side-by-side pic of the old and new TPS. Only the center rotating part is different but it fits and works just fine. It also has a better fit so there is less slop and almost immediate response.
NewOldTPS.jpg?t=1269362105
By the way, the original TPS was working fine so I have no idea what the symptoms of a bad TPS are. Since it was available I replaced it to have a spare and to see if this one would work. Both Pete and I thought it would and we were right.