Santa FE SM (2001-06) :: Rear Suspension Failure After Recall Check
May 1, 2013
My 02 Santa Fe was checked after recall notice November 2011- and passed- On 20th April 2013 sudden failure of drivers side rear suspension - fortunately no fatalities and no third party involved-The passenger and car was brought home on a low loader by the RAC. Notified the Hyundai Recall Administrator and was passed onto the Consumer Service Team- Sent the requested car information and pictures of the corroded rear suspension the same day. Was told the person dealing with this is going on Holiday- Result so far- Car still on my drive and no further interest from Hyundai- Not sure what to do next?
View 1 Replies
Advertisement
2004 Santa Fe, 2.4L auto, 133k miles that I just purchased. I've just been getting all of the maintenance up to par before driving it, I noticed the suspension makes a decent amount of noise when going over any kind of bump. The rear end makes a squeaking noise, which I think is from the trailing arm bushings. The trailing arms look like this:
When looking at the bracket where the big bushings goes, it looks like the arm is almost touching the one side instead of being centered like it should be. I'm thinking the bushing is just shot and allowed the arm to be pulled rearward. I know 01-03 had a recall for rusting trailing arms, but that doesn't work with my 04.
Other various creaking noises I'm thinking are coming from the sway bar bushings and links. Control arm bushings still look solid. Might replace the rear shocks if I have to with some KYB's.
View 3 Replies
So I own a 2003 Hyundai Santa Fe GLS 2.7. I am the fourth owner and currently there is 168k miles on the vehicle. I purchased the car with around 110k miles on it and have had it for nearly 5 years now.
Aside from general maintenance I have never had a single issue with it, until last weekend. On the way back home from a road trip I began to notice a whining sound, and then very abruptly the car shook and I lost control of the vehicle and had to pull over on the shoulder. I was on the highway and was VERY fortunate to not have gotten into an accident.
After inspecting carefully I discovered my 4WD Drive Shaft was literally hanging by a thread. The knuckles were ruined, and in the process my Transfer Case and Exhaust System were all severely damaged.
View 13 Replies
Rear end Suspension noise, '13 Santa Fe Sport 2.0T? I purchased a new '13 Santa Fe Sport 2.0T in Sept. 2013. Shortly after I noticed the rear end of the car creaks/squeaks when the suspension compresses thru it's travel. This happens when driving over tall speed bumps at 2-3mph or into/out of steep driveways at 2-3mph. Rear end noise/squeak at anytime?
View 49 Replies
I got a call from the wife at work telling me the vehicle was making a loud noise when being driven. I told her it was a bit hard for me to diagnose since I was at work and to leave it parked till I got home. She really had to go out so she decided to drive it a short distance and come home.
I got home and discovered the drivers side spring was sitting on top of the inside of the front tire. The spring had done a superb machining job of the tire tread to the point I was amazed that the tire still held air. Anyway long story short the beast is in the shop having both front springs and struts,tires etc. being replaced. The spring actually broke.
I just bring this to the group as I did a search on google and this is not an uncommon, occurrence on these santys. We /she are just lucky this happened at a low rate of speed,as a highway speed incident like this would not have been pretty.
View 4 Replies
When I go over bumps or rough surfaces I hear a rattle in the rear suspension. It sounds similar to the noise bad ball joints make. I recently had the car aligned and the shop said they couldn't find anything wrong. I'm going to take a look myself but was wondering if this might be a common problem. If maybe there are certain bushing that are known to wear out.
View 2 Replies
I have a 2001 F150. Front brakes replaced a few months ago. Last night, I realized my rear brake lights weren't working. I'm not sure how long they've been out or if it's related to the bigger problem.
While testing the brake lights by pressing the brake pedal, the pedal seemed to give out and sink lower. While driving the brakes worked but only when I pushed the pedal all the way in. Eventually the ABS light came on and stayed on.
View 3 Replies
Santa Fe 2001 2.4l. How can I check or test a MAF sensor? I replaced the sensor four months ago but now I have the P0102 error code again. I would like to have recommendations before to clean it or replace it again.
View 4 Replies
My '04 santa fe 3.5 v6 gls/lx, 79k miles, gas, auto, check light has just come on while I was driving a less than 10 mile journey. How can I check what is wrong. Do I need some sort of diagnostic code checker. Do any national outlets check it for free (Pep Boys or Auto Zone, etc).
Just 5 days ago (about 50 miles only) I had timing belt, water pump, plugs and leads replaced, brakes checked and lubes flushed; BUT not at above dealers. I would rather know what the code is saying before I go back to the shop who carried out the work.
View 12 Replies
How can i turn off check engine light (hyundai santa fe 2003 3.5) by fuse ? I do not have any code scanner.
View 10 Replies
I recently purchased a 3.5 V6 Santa fe. The Check engine light keeps going on. I took it to a few shops and I am getting the same code. It is the O2 sensor in bank one. (I think the the code was po170.) The light keeps going on and off. All I can find are the same problems with different Santa Fe engines (2.7, etc. )... My SUV has 100,050 miles on it.
View 1 Replies
Recently I changed the spark plug and I made a mistake crossing the spark plug wires. here I noticed that the check engine warning don't turn on.
Also I had other problem with idle air valve and also the check engine warning don't turn on.
The light is working fine because when I acct the key it is turning on. The problem is detecting a fail it don't turning on.
View 5 Replies
Was driving on some segmented highway concrete that send my front end into quite a thrashing. Slowed down quite a bit and it settle down some but nothing like that before. Pain attention to ride but it feels OK, corners, etc. BUT, over the past few weeks, I've noticed that it has become quite sensitive to sharp transitions (BOTS dots a.k.a. line markers, driveways, etc. so I have a suspicion that one or more of the air spring assemblys has possibly failed or a leak.
It's like the equivalent of a worn out strut. The car hold up. Raises and lowers, etc. But I can't push down on the car to test the response of the suspension like a standard strut car. What is the expected life of the air suspension? And cost to replace pair or all four. Not looking forward to the possible expenses.
View 5 Replies
Having problems with air suspension/compressor? Mine has totally failed with an error message of RUNNING GEAR FAILURE- WORKSHOP!
View 5 Replies
I have had a check engine light go on and off with P0700 and P0741 but since the flush day 3 it hasnt come back on and it was chucking with rpm doing small jumps... but now it does it in the mornings after sitting all night after a few chucks its fine for the rest of the day til the next day no check engine light so far, but transmission flush has worked a lot not as bad as before the flush.. So what else could be causing it? Its a 2006 hyundai santa fe with 274,000 kms.
View 24 Replies
I have A 2001 Santa Fe. The check engine light came on about 3 weeks ago and the car was still running fine up until the last few days it felt a little sluggish. Today I got a little muffled backfire noise. It was like a putting noise if I pushed on the gas to hard to speed up. The car has 95,000 miles on it.The car starts up with no problems and doesn't stall. Its A 6 cylinder All wheel drive vehicle.
View 10 Replies
Check engine light on, car stalled once. Pulling code p0320 "Engine Speed Input Circuit Malfunction." Tachometer works intermittently. Where do I start?
View 2 Replies
Recently got check engine light fault code p0320
2005 3.5 with 172k miles
View 2 Replies
I have a 2002 SF GLS/LX (?) with 2.7 L V6 2WD (60,000 miles) and it started to apply the ABS brakes in a random manner. Found out it was caused by a broken front wheel tone ring. So, I pulled the ABS fuse under the dash and it stopped the brake problem. Drove it today to pick up some wood and now the check engine light has come on.
My neighbor has an OBD scanner and he plugged it in and said I have a P0501 code and a P1529 code, but he didn't know what they meant. What they mean and are they related to me pulling the fuse under the dash? Did I pull the wrong fuse? Is there another fuse somewhere that I should have pulled?
View 1 Replies
My 2002 Hyundai Santa Fe 2.7L V6 AWD failed to start a week ago. After towing to my neighborhood repair shop, it was diagnosed as a faulty ECM based on code P560 (System Voltage Problem). They replaced the ECM (along with relay) with a used one with the exact same part#. After that, the car was started and run OK but Check Engine Light stays on all the time. The codes displayed are:
P1529 TCU MIL Request Signal
P0501 VSS Range Performance
I was told that this is caused by the fact that each ECM is VIN/PIN locked. The replacing ECM was used in another car before and was locked with a different VIN thus cannot communicate with some components of the current car.
My questions are:
Can this used ECM be unlocked and relocked with a new VIN/PIN? If so, does it require the previous VIN/PIN to unlock? Most likely the previous VIN/PIN is no longer available.
Does this service require the presence of the car or can it be done with the ECM alone? Do keys need to be re-registered? The car starts fine currently.
View 11 Replies
I have a quick question about the control arms on the B5. I have an 01 Passat GLX 4motion, the was previously my mothers. She had the upper arms (iirc) replaced around 60k but not all of them. I got the car with 64k from her, and it now has 92k of mostly highway miles. I have a few clunks from the suspension but nothing crazy, and considering the shocks and dampers are probably shot i cant seem to tell if its the arms or the shocks.
View 1 Replies
