Santa FE SM (2001-06) :: Power Lacking Until Hits Around 3000 - 3500 RPM
Aug 24, 2014
I've got a couple of issues with a 2002, 2.7ltr v6 santa fe first off when taking off steady the car runs fine but taking off quickly it seems to lack power until it hits around 3000-3500rpm est then it takes off fine and all threw the upper rev range the auto seams sluggish but I'm not shore as I haven't driven another 2.7ltr as a benchmark. No error codes are present.
The second issue I brought a new keyless remote for the car and looked up a thread on how to program this they had reference to a set switch behind the fuse box behind the lower dash panel I went looking and found what I think is the remote receiver it has what is like a antenna cable plugged into it but no set-off switch at all is there any way to get this new remote programed or will it have to be done threw dealer or is there something I would be missing?
View 9 Replies
Advertisement
I am after to find which USB cable and software can be used on my wife's ... 5/05 v6 Santa Fe to check the error codes. The car is revving up and down when cold and lacking power when warmed up, I'm guessing it's a sensor but I need to find which one.
View 1 Replies
I have this problem with my 2001 Santa fe 2.7 Lt auto done 326,000 km no power on hills sometime want rev past 3500 revs and sometimes will rev past this, it seem to get worse when fitted new fuel filter in the tank? have put new filters and O rings in injections, have just fitted new coils and the cat has no restriction. Starts first time but did have trouble the auto would not start in park until pulled top cover and got it out of park and started it in neutral changed the trans fluid and seems to move through the selection better. Could it be the fuel pump??
View 4 Replies
I have had the Santa Fe back and forth to the garage no power. We where driving it and all a sudden dropped power can't rev motor over 3000 rpm. Garage said they fixed it with dry gas and more gasoline b/c it was "low" between 1/4 and empty?
View 12 Replies
I have an '08 Camry purchased a week ago. When I accelerate rapidly and the rpm hits 3500 to 4000 I hear a metallic grinding noise. It is only while crossing this rpm range. Only on acceleration. I have had some luck replicating the grind and making it last longer by feathering the throttle and holding the rpm in this range. It does not happen at any other range and I can get it to happen in D or 4. Have not tried other gears. My thought is some sort of drive train issue but the dealer mechanic says maybe an engine mount or something else. Sounds too metallic to be a rubber mount to me.
View 2 Replies
I have been noticing this Rotten egg/sulfur exhaust smell I have been getting for the past 2 months. So far it only happens when the engine hits 3000rpm or higher.
View 9 Replies
So, I recently got my car serviced with balance shaft belt, 2 idlers, crank sensor, timing belt, spark plugs, ignition wires, and ignition coils. And now when i drive my car and accelerate it to about 3400 to 3500 rpm i get this rattling noise from my engine then when the rpm surpass that range i dont get any noise anymore. I really don't want to take it back to the shop and have to be charge for a diagnose but I am thinking it could be serpentine belt or loose of the down pipe.
View 6 Replies
Symptoms- won't rev over 3000-3500 rpm's, upon acceleration (especially uphill) seems to struggle and won't accelerate much at all, seems as if trans changes fine. BTW, throwing no codes at present.
What I have already tried...new air filter, new fuel filter, had cat. check (was told stopped up but when removed found it was not and truck did the same even with cat. off), o2 sensor (upstream) replaced, battery disconnected to reset computer.
After reset of computer, runs a little better but still not good. Seems to start if you accelerate to quickly or when truck reaches around 40-45 mph.
View 11 Replies
5 miles to the airport last night, cruising on the freeway, my transmission suddenly accelerates from the steady 3000 rpm to 3500 rpm. When I press on the accelerator, the engine speed and my actual speed are no longer in sync. It feels like the transmission is no longer shifting. The radio cuts out and all the lights dim. My airbag warning light flashes intermittently at me. I make it to the airport, afraid to turn the key off; but I must. I attempt a restart - nothing. All red lights but no engine cranking. What gives? A fuse, the alternator? The car - 2003 mazda protege. The driver - stranded when I return home.
View 3 Replies
Car: 1995 Corolla 1.8L automatic
Symptom: misfires around 3000-3500 RPM only when warm.
I have replaced the following:
-Spark plugs, wires, cap, and rotor
-Ignition coil
-Fuel filter
-Poured some quality fuel system cleaner into the gas tank
The car stutters when accelerating in any gear hard enough to reach the engine speed that the misfire occurs at. It doesn't backfire, it just misses... I am confused since so many of the misfire issues I know about that are RPM specific are spark-related.
I have considered cleaning the injectors, but don't want to go through the hassle to remove and have them cleaned unless I really have to. Checking if hunch on the injectors is correct? Something else?
View 3 Replies
Codes currently on ecm: P0134, P2125, P1174, P0735 My 2003 Santa Fe 2wd 3.5l with 160,000 miles was driving fine, then all the sudden whenever I reach about 3500 rpms there's a grinding noise that sounds like its coming from near or in the automatic transmission. As for the codes: P0134- I just replaced the o2 sensor with an oem part from autozone, so not sure why that's popping up. The connections look fine. P2125 and P1174- I'm trying to figure out whether the accelerator position sensor or throttle position sensor needs to be replaced. I have a multimeter but don't know if that will be able to tell me which one is out. The P0735 gear 5 incorrect ratio and grinding noise at 3500 rpms is what I am mostly worried about though. Could a transmission flush work with that?
View 2 Replies
My 1994 Acura Integra makes a buzzing noise exactly between 3000 and 3500 RPMS. It sounds kind of like the sound a circular saw would make cutting wood. It only happens when I am accelerating through that range. Also, sometimes after driving for a while, it doesn't last as long and the noise stops around 3300 RPMS. I've checked the heat shield and it seems to be fine so I don't think its that. What this could be caused by?
View 3 Replies
Looking for a good diagram of the complete vacuum system on the AEB 1.8t 99 passat. I am throwing a 1136 code which is indicated as a "Manufacturer controlled fuel and air metering". I recently finished a complete rebuild and engine is finally back in but running in limp mode. During the rebuild, I used mobil 1 synthetic as an assembly lube for all internal components including valve train.
I immediately wet fouled O2 sensors and spark plugs. After repeated removal and cleaning for plugs and O2 sensors i have progressed beyond seeing the "wet" fouling but plugs are still very rich, black in color but dry. Engine starts and runs at idle(lumpy) consistently and will run for as much as 5 minutes but very rich. If i rev engine to 3000-3500 rpm it will "POP" or backfire and immediately stall.
View 5 Replies
I made an earlier thread about minor low speed crash and airbag deployment that has sense been fixed.
The engine 2.0 (AZG) will rev to 3000 (3200 sometimes) RPM and stop. This is only if you give it about 20% / 25% throttle. If you give it full throttle it spits and sputters. When I had the airbags installed. The codes were read it and also came up for cam sensor and o2 changed that and now the codes are gone. No CEL and it is exact same issues still. I can't tell if ECU is doing it but it feels like it's not getting enough gas or air since full pedal makes it stall.
View 1 Replies
00' 7.3 is acting a little strange lately. i was towing a 15 foot trailer the other day for about 250 miles that wasn't all that heavy and my foot felt like it was very close to the floor. I had it to the floor and the truck would only go 60. now even without that trailer its better but still i feel as if i have to really put my foot down into it to speed up. if i go all the way to the floor in o/d it'll downshift and start speeding up but very very slowly then i run out of pedal and am at the floor, a lot slower than before. Before i wouldn't get to the floor and id already be moving pretty good. but now i gotta keep it pretty much 3/4 way down and keep it there to get up to speed and stay there. truck has 253k no tuner or programmer just 6637 intake and an exhaust, ww2. leveled on 35's. the tranny isn't slipping or at least doesn't seem to be. She doesn't shift perfect but its not anything crazy bad for stock with 253k on it. maybe something wrong with the actual pedal? or hopefully not but maybe the trans or motor , or maybe a sensor or something?
View 14 Replies
I have a 2000 Honda Civic Ex automatic 225k miles on it. Recently replaced spark plug and spark plug wires. Just had an oil change and an inspection done; they found an oil leak in the oil pan (oil pan cover gasket needs replaced). I have a severe lack in power, meaning it doesn't have the get-up-n-go it should. Doesn't shift until it hits 3.5 rpms, idles pretty loud, and noticed earlier today that there is a rattling that seems to be coming from front drivers side(could of been the road, adding it in for good measure) but that didn't happen till i hit 65. The coolant tank has a black grime in it, and from what i understand that's from deteriorating hoses(?). My question is this: What could be causing this loss of power?
View 4 Replies
I have here a 2001 3/4 ton Suburban. It arrived last fall with 280K miles and a 6.0L V8 that was on its last leg (low to no oil pressure). I dropped in a 5.3L that I had handy, and had been happily driving it throughout the brutal Minnesota winter.
A couple months ago I noticed an issue developing. After a cold start, the engine would be severely lacking in torque for the first minute or so of driving. You could reach any RPM you wished, but the truck could barely accelerate. Once a minute or so had passed in this fashion, the issue would suddenly disappear... you'd be thrown back in your seat a bit if still attempting to accelerate, and the truck would take off. For the remainder of the trip, things would be fine.
Recently I went to drive the truck after it had sat for some weeks. It started fine, but the issue was now more persistent. When trying to accelerate, the gutlessness would continue for a good 15-20 seconds until finally and suddenly disappearing. Let off the gas, wait a moment, try to accelerate again, and it was the same thing all over again. Eventually I also noticed very obvious stumbling/missing when trying to get moving from a dead stop. Idle remained smooth.
The plugs and wires are only a few months old. The fuel filter is new. I checked for vacuum leaks (none that I could find). Fuel pressure is consistently around 50psi, even while the issue is happening.
The MIL was not on. I checked with my scantool, and found that P0101C was set, with P0101 pending. Visually examined the MAF harness and sensor; all looked fine. Swapped in a used working MAF; no change. (I suspect these codes may be due to the fact that I'm running a 5.3 with a stock, unmodified 6.0 PCM.)
My scantool is a Genisys running System 2.0. I'm by no means an expert with it, but I did know enough to try watching the miss counts while the symptom occurred. All cylinders seemed to be missing equally as much as the others, more or less.
Normally I'd be suspecting the fuel pump and/or associated wiring was going bad, but the pressure seems fine. What I might be missing?
View 10 Replies
I have a 2010 Camry Le with the 2.5 4cyl. What I'm trying to diagnose started in the last 2 weeks, the engine just seems like it's lost some power overall but there is no unusual sounds coming from the engine and it has not triggered and codes. I have checked the simple stuff like the air filter and plugs but am not sure where to turn next.
View 7 Replies
My 97 Subaru sport has trouble starting when left until cold, it always finally starts, but wont rev at all until its has been running for 20-30 seconds.
Other symptoms include....Once running it also seems to be lacking power across the low rev range. but then seems fine above 4k rpm.
If i get stuck in stationary traffic for a while, the check engine light comes on and i lose all power, it hardly pulls its self off to a start. But if i were to rev the engine and let it drop back to idle a couple of times the light goes off and i get power back to set off.
View 1 Replies
My mom has a 2011 GL Hatchback about 20k km's... She decided to take my car this Saturday without telling me and I was stuck with hers.... All of a sudden the check engine comes on and at idle there is like a bogging going own. (Shaky putt-putt-putt-putt) early acceleration is lacking power and it smooths out at higher rpm's.
I can do minor things on my own like plugs and brakes, I would love to be able to get it running smooth again.
View 4 Replies
I have a 2006 Ford Escape Hybrid with about 150,000 miles.
It sometimes is lacking normal power - slow to start but fine once to full speed. When it is lacking power I notice that the gas engine is not shutting off when stopped at traffic signal like it normally does with charged batteries. It will be like this or a few days and then suddenly has its normal power and shuts of at traffic signals again.
Seems to be some failure of communication in the hybrid controls with system not telling the electric motor to do its thing. Where I should start looking for fix of this intermittent problem?
View 4 Replies