I have Santa Fe 2002 v6 2.7 and it's have been in the mechanic for 2 months now.
Suddenly my gear box don't go up 3rd, the error that the diagnostic reader is P 1528. What it can be? How to Fix it?
I've checked the lines from the Purge Valve on the Passenger side of the Intake Manifold, Check OK
I've Checked that Valve OK
I've Replaced the Canister Close Valve
I've got the Gas Cap tight.
I've removed the rubber bushing holding the CCV to the Evap Canister, hoping to isolate the Filter and point the blame on it, no luck there!!
I'm thinking next is to drop the Tank and check over all the Goodies on top.... as much as I hate the thought of that, the two access holes under the seats, just don't allow access to enough of the tank!
any thing there that I could suspect, I see there's a check valve!
There's also the Fuel Tank Pressure Sensor, which may be at fault.
It seems that i'm most likely going to have to replace the entire plenum .
P1159 here are some details. [URL]..................
I've checked all connecting wires and none appear to be loose. When the issue started to occur and prior to discovering the P1159 code, I also replaced all coils. I replaced the coils because one was arching over to the metal of the engine. I assumed this may be my problem. The issue still persisted obviously. The check engine light never came on so I assumed I wouldn't get a code. I took it over to a friends house with a code reader and that's when I discovered that it was actually giving the P1159 code.
Are there any other model cars that utilize the same engine that I could use the plenum from? Getting this in working condition is going to be the difference in what I can get for it.
I have a 2003 diesel GS Santa Fe, every now and then when driving the ABS light comes on, not very often but it does, if I switch the ignition off and restart it goes out, I had it on a fault finder computer and it showed code c1274, I think its something to do with the G sensor and the way it breaks (ABS) is it an easy fault to fix? What are the costs involved and will it affect the driving of the car, like I say it rarely comes on and I don't notice any change in how it drives.
View 1 RepliesStill getting p0174 error after upsteam downstream, checked everything.
View 1 RepliesSo the check engine sign came up on my car and using the OBD it tells me the error is P0113. After googling the information, it looks like I have an issue with IAT sensor.
I opened the air filter and what I believe what could be the sensor and there was nothing clogging up, so I'm assuming the sensor needs to be replaced
Question is where is the IAT sensor located and how do I dis-assemble it so I can replace it. Is it the piece that is located just before the air filter?
I just joined the forum mainly to care of my dads 2001 Hyundai Santa Fe but also I got a check engine light on my way home from work last night.
From last night I saw that oil was all over the timing belt. Today I inspected it with a Coworker and his OBD II reader.
Error Code was P0455, EVAP - Evaporative Emission Control System Leak Detected (gross leak).
Now the oil leak is stronger since the oil spills is on hood (inside hood). I will make a picture tonight when I get home.
I personal think it's leaking from a tube/ valve on top of the timing belt (picture will show more tonight). Thinking of cleaning the timing belt area, then drive a little around or leave it in idle to spot where the leak is from.
Common issue? I googled around but since P0455 is a common issue (on my 9-2x as well) I couldn't find anything about this I am also limited from my search since I am currently at my work PC incl. strong firewall.
I will see if google let me find a picture...
Engine light come on and everything is running great, this morning got this error code U0d00. Went to advanced auto and had them run a scan.
View 5 RepliesMy Hyundai Santa Fe 2006 V6 3.5L shows error code P2100. I cannot for the life of me find the ETS relay. Ive scoured the net but just found vague drawings and pics that didn't show ETS relay. I would also like to know is the ETS relay also known as the fail safe relay or is that a separate relay. Ive seen pics of the fail safe relay but none for the ETS relay. If there is such a relay, exactly where it is located?
View 2 RepliesI got an Error Code of U0D00. What this is or means. The scan tool says to refer to your manual but I don't have one.
What the vehicle is doing is that it will work fine for a while then when you stop (in park) the engine will rev really high and back down all by it self for example. It will go up to 3.5 and back to 1 rpm repeated. Then when you start moving the car it will continue to idle higher like you are pressing the gas. During all of this the check engine light will appear?
Its not my car but my sister in laws. She stopped by our house tonight to pick up her kids and when she put the car in drive it showed both drive and 2nd gear. we tried disconnecting the battery so she could at least get it home (3 min away) but it didn't change anything.
She left with it still in 2nd thinking she could make the short drive without any problems but half way home it shifted down to first and it wasn't even driveable. Everything i have read on the web (which was not really specific to the santa fe) was say that its stuck in safe mode. What could have cause the problem? So far no check engine light has come on.
ok, I had quite bit of work done, prob over yr ago All oem parts, timing belt, crank sensor, idler pulley, some other things while in that area. So when he was done I got this vibration when it goes into gear never in park only in rev. or drive but only in cold weather and after it warmed up it was go away. No Trans service was done. He kept it overnight outside, had the timing cover off rolled it in the garage, started it and seen that the belt was flapping crazy. So he thought it was that. well every cold morning I have to wait till it is warm to not hear that sound. it only happens during cold mornings never in summer. He had back in his shop 3 times after parts were installed. and its to this day isn't the same. its unfortunate that I didn't have many cold mornings when he had worked on it. but after I had it and the next cold morning it was there.
View 7 Replies2003 Santa Fe 41,000 stuck in first gear.
View 1 RepliesTwo times in the last month my 2003 Sante Fe would not start - the radio, air conditioning will come on but nothing from the engine - not even a click - no check engine light. Had it towed both times - as soon as it was towed it would start up. It seems to happen in 2 week intervals. Now I realize bc they had it in neutral to get on the truck that is what required to start. It hasn't happened in a week but I know it will again.
View 3 Replies2003 Santa Fe, 2.7L V6
When placed into Drive, the transaxle (and indicator lights) behave as though the gear selector was in the manual gate and at 1st gear. It seems that no matter what I do (wiggle the selector, disconnect the battery, etc) will bring it out of 1st gear while in D. This issue first occurred about a month ago and it somehow corrected itself. I had hoped that it was a fluke, but it is happening again. Initially, I suspected that it might be a switch or something within the gear selector lever housing in the console, but I've done a bit of searching the webs and it looks like it may be more of a sensor(s) issue.
I've been having ongoing issue with lack of power uphill in my 2005 2.7L Auto and noticed during recent freeway driving that when its in cruise mode the car will shift down through 3rd then into 2nd to maintain cruising speed on a steep-ish slope.
That was with adult driver me and two kids in the car so no extreme load involved.
Does car needs to be in such a low gear at 110kmh/70 mph to cope with a slope?
My Santa Fe 2001 model V6 4X4 Automatic shift gears down hard from 3rd in to 2nd. I checked transmission oil and its light brown. Should I drain and refill or not worth it.
View 7 RepliesThe shifter will not usually stay in 5th gear for very long. The clutch and flywheel were replaced a few weeks ago just before i purchased the car but this problem has only cropped up in the last week. Could it be shifter linkage adjustment?
View 3 RepliesI have a 2004 3.5L Santa Fe with about 170k miles on it.
Runs great. I am going to change the timing belt here in the next week or so.
I have started having an issue where going into second gear it will jerk, almost like sputter. Does not do it all the time. Seems like a sensor or computer issue because the rest of the gears shift smooth. And if was a problem with the internals of the transmission I would think it would always do it and never go away.
What the issue could be since I am already going to be digging deep into the vehicle might be worth replacing more parts, what it is.
I have an 01 and 02 santa f. I took the v6 out of 01-and put in the 02.put new gaskets on engine new timing belt etc. Got engine in and runs like a champ. But the tranny which looks new I assume its been replaced. It starts out in 2 or 3 all the time want shift into od. Reverse works. So I found one plug dangling I couldn't figure out where it went then i found it. It plugged up on top of tranny. Well now it starts out in first and shifts through all the gears. Drove it down the rd shifted fine. Turned around and put in reverse then when i went to drive it jerked real hard. Shifted out fine so I went to floor it to make it kick down and it jerked again. This time it was hung in 3 or drive cause when I pulled into my driveway it was in high gear and u can put it in manual mode and the light only goes to second and d when it acts up like this. So i killed the car started back up and know it will go into first in manual mode and shift out and do fine?
View 3 RepliesI have a 2002 Santa Fe V6 2.7 liter, FWD, 215,000+ miles. When it shifts from 2nd to 3rd the whole vehicle jerks. It does not do this on the other gears. I took it by a transmission place for a free scan and they said the transmission is fine.
View 19 Replies