Santa FE SM (2001-06) :: P0103 Engine Light Code For MAF Sensor
Apr 29, 2014
I have an 2004 Santa Fe and im having some Mass Air Flow Sensor problems but I dont know what's wrong. My engine light came on for the second time after awhile. And I got it checked for the code and of course it was my sensor again. The first time I just giggled it around and the light went off. I did the same thing today with giggling it again went off. So I feel like it might be a loose connection but I really hope it isn't failing because im pretty sure that's uber expensive to fix.
View 2 Replies
Advertisement
I recently purchased a 3.5 V6 Santa fe. The Check engine light keeps going on. I took it to a few shops and I am getting the same code. It is the O2 sensor in bank one. (I think the the code was po170.) The light keeps going on and off. All I can find are the same problems with different Santa Fe engines (2.7, etc. )... My SUV has 100,050 miles on it.
View 1 Replies
Engine light come on and everything is running great, this morning got this error code U0d00. Went to advanced auto and had them run a scan.
View 5 Replies
I have a 2005 Santa Fe with the 3.5 with 112000 miles on it. I had the engine light come on with the code P0302 cyl #2 misfire, I got spark plugs, plug wires to do a tune up on it. I changed all of it and got it back together, started it up and it still had a miss to it. I then took the front spark plugs out and did a compression test on it. #2 was at 85, #4 was at 120, and #6 was at 160. I couldn't check the back cyls because I had already put the intake back on. I then did a wet test, and all the cyls came up to 160. So this tell me that the piston rings are bad in #2 and going bad in #4. I have kept all the oil changes up and up to this point I haven't had any trouble with it. Having this problem with there 3.5?
View 1 Replies
Check engine light on, car stalled once. Pulling code p0320 "Engine Speed Input Circuit Malfunction." Tachometer works intermittently. Where do I start?
View 2 Replies
Recently got check engine light fault code p0320
2005 3.5 with 172k miles
View 2 Replies
My 2003 Santa Fe 3.5 is in limp mode, you can't change the gears and showing signs of faulty tps sensor, but my mechanic is telling me to change whole electronic throttle system , May be its only the sensor.
View 1 Replies
What is the possible, or most likely, cause of a Knock Sensor No 1 Circuit Malfunction reading??
View 1 Replies
My check engine light came on the other day and the code stated the the "throttle position is open" so after researching and everyone telling me that i need to change the sensor. I did everything after was fine running better but today only after 3 days replacing it i get the same problems. car has no get up and go hardly can push to 20 mph and when in idle i press the break it starts to bog down and almost want to shut off! and can be really loud...
Santa fe 05' 3.5L ....
View 5 Replies
I have a 2005 crdi diesel santa fe that i have a strange problem with it starts up first time no problem in the mornings and can drive all day long. However if i switch it off and leave it sit for about a half hour no way will it start again until it cools off. It will start though with a push start instantly!
I got only one fault code P0340 cam shaft sensor fault, i replaces sensor and made no difference. Is this a common fault???
View 4 Replies
My hyundai 2004 sta fe awd 3.5 LX engine light came on while cruising dwn the freeway. At the same same time i heard a loud thud and speed went down from 65 to 40mph and a high idle. I drove it home and hook up the obd2 scanner and got P0720 suggesting bad output sensor. So I decided to buy new sensor from the dealership, put it in and thought it will fix the problem. After few days the engine light came on (P0720)again with the same clunk noise and speed down from 65 to to 40 mph at high rpm. Took it home, did some experiment by putting back the old sensor. I Connected the harness back, but this time I wrap the female connector with the electrical rubber tape and electrical vinyl tape. Problem fixed. No more engine light,transmission shift smoothly. I think the connector (harness side) to the output sensor was crack that's why its not making good solid connection. The rubber tape technique held the female connector pins tightly together. New part didn't do anything but it was a learning experience.
View 1 Replies
I have a code reader got P1193 - MAF sensor low voltage
Is it shot or just need cleaning? Or is it something totally different
2005 Santa fe 3.5l
View 2 Replies
My check engine light is on. I got the code pulled at Advance Auto Parts. It is P0107 - MAP Sensor Circuit Low Input. I wanted to test the MAP sensor to see if it is bad. I couldn't find anything online that was Santa Fe or even Hyundai specific as far as testing procedures go. I know you can test the power wire, the ground wire, and the signal wire, from what I could tell from other places I've looked. I got 5ish volts from the power wire and 12ish volts on the ground wire, which is what I understand they should be. I don't have a vacuum pump at the moment, but testing the signal wire with no vacuum I got about 0.02 volts. From what I've read online, it should be around 5 volts, but I wasn't sure if all MAP sensors work the same way. Whether I'm doing this correctly and whether they think the sensor is bad?
View 5 Replies
My Santa Fe indicated P0715 for input speed sensor problem. I purchased both sensors and based on forum input I removed the air box and battery to access senors. Output speed sensor is easy to see and access. I am having a problem locating the input sensor. I see wires going to a sensor under both the main wiring harness and shift cable. Is that the location of the input sensor? If so how do you move the wiring harness and shift cable to allow access? If not, where is the input speed sensor located? The Santa Fe is 2001 V6 2.7L.
View 8 Replies
Getting code P2125. Read on here to get some electric contact cleaner and see if that works by cleaning the connections.
If I do end up changing out the Throttle Position Sensor, what voltage value do I look for when installing the new one ?
View 8 Replies
I know the code is fuel level sensor, but i can't find the parts online. nothing comes up with the part name fuel level sensor. What is the part number for this or the number for kit because i believe there are 2 sensors?
View 1 Replies
02 Santa Fe 2.4L/ automatic/2 WD. I replaced the fuel filter (only) and have had a nightmare ever since. It takes multiple tries to start, running a little longer each time. When it will finally stay running, only the most delicate of throttle feathering will allow any RPM's to be built up. Any attempt to do otherwise will result is sputtering, bucking and other unhealthy behaviors until the throttle is closed. It also gives off the smell of running rich.
I borrowed a scan tool and got P0136 and P0141, which I expect since the O2 sensor wiring was cut in two by the heat shield shortly after my daughter bout the vehicle. It also is giving me the P0340 Camshaft Position Sensor Circuit code. I had replaced the CMPS and its connector a couple of month ago. I replaced the sensor again to no avail. I have checked the Orange/Black wire from the connector to the ECM and it reads 0 ohms. I get battery voltage at the connector on the Blue supply wire but only get 1.86 to 2.0V when I check the signal with the engine running.
View 6 Replies
I recently replaced my MAF on the car with part number 06A 906 461 A which is not the 07D 906 461 part number. I take it that this is wrong because i am getting power surging in the car at WOT and I have a pending DTC code P0103.
View 1 Replies
2003 Hyundai Elantra, 1975cc engine, XD. P0198 Error Code.
I know this is the Engine Oil Temperature Sensor High code and I have seen indications this may mean high voltage on this sensor. My problem is I cannot locate this sensor on the engine. From what I have read this sensor is supposed to be on the driver's side of the engine on the head, rear side.
On my engine the head was replaced (unknown to me when I recently purchased the vehicle). From all indications this is not a CVVT engine. The air intake has a MAP sensor that is connected and appears to be functioning properly. The driver's side of the engine does have two coils but I can see no other wires from the wiring harness toward the rear of the head other than leads to the starter.
The cam sensor is located on the passenger side of the engine, rear side. I have found the oil pressure sensor and crankshaft sensor on the front side of the engine block toward the driver's side. I have found and engine temperature sensor on the driver,s side of the engine on a housing connected to a radiator hose.
Oddly enough there was an OCV hanging on the harness toward the front driver's side of the wiring harness. Adjacent to this plug is a second plug on a shorter lead that is not connected to anything. Both of these plugs have two leads but are shaped differently oval for the OCV and the other is rectangular. I am wondering if this rectangular plug is for the engine oil temperature sensor? What I cannot see is where the temperature sensor would screw into the head on the front driver's side (near this plug).
I went to NAPA today and they do not have an engine oil temperature sensor listed, but I was able to find one on line. I cannot find a connection point on the head that looks like the picture of the sensor on-line.
View 3 Replies
About two weeks ago I purchased an intake from a member here on vortex. I installed it, drove the R a few times, and ended up getting a CEL right afterwards for P0103 (maf circuit high). Does this have anything to do with the intake install? Car runs absolutely fine.. no weird issues. Never heard of an intake causing a code like that. Cleared it.. it came back.
View 4 Replies
124k, original owner, no mods. Car was running rough and stumbling a bit. A bunch of codes came up. I replaced coils because I had them, spark plugs look good. One code came back p0103. I cleaned the throttle butterfly and replaced the maf sensor. Still same problem.
When I first start it cold it idles high but stays running , once it warms a little the idle drops and then it won't stay running. Then the traction control light comes on and then the cel. I checked for a vacuum leak but came up with nothing.
View 14 Replies
