Santa FE SM (2001-06) :: No Power When Pulled Into Gas Station / Cranks But No Fire
Aug 31, 2011
Here is what happened. Pulled into gas station and car just died. Tried to restart and no fire. Cranks but no fire. Flat bed trip home and started to diagnose. Thought it was a bad fuel pump so I pulled and tested with a direct power and functions fine. Checked all fuses and relays, all seemed fine. checked for power at pump and nothing. Reset cut off switch and still nothing. Thought maybe ECM relay in the under hood fuse box was bad I borrowed the one out of a friends car. Nothing. Thinking ECM was bad put theirs in my car and got power to pump. So I put their car back together thinking mine was the ECM, then theirs won't start. The ECM relay i took from there car and put in mine blew when i tried to start my car. Got another ECM for my car and put in. Still no power at the pump. Here is the info about the car. 2001 Santa fe 2.4L auto. 80,000 miles. Timing belt, tensioner and all Idler wheels changed along with water pump at 71,000 miles. This car has been very reliable up till this point. No check engine light came on at any time..
View 8 Replies
Advertisement
Having an issue with my 2007 Santa Fe 3.3L. When the engine is cold, been sitting for a few hours not when the temp outside is cold, it takes about 5 to 8 cranks before the engine will fire. I can then shut it off immediately and start it again and it will fire right up.
I currently have the P0464, P0463 and P2068 check engine error codes for the fuel level sensor units. I don't really know if these are directly related as I've had them for about 6 months and the starting issue has just shown up the last month or so. Plus, I would assume these should only be related to sending fuel level information to the fuel gauge. Either way, I'm still leaning toward a fuel delivery issue since it only has a hard time starting when the car has been sitting for a few hours. I don't know if maybe it's the fuel pump or a electrical component. If it's the fuel pump, I'd like to do that when I take care of the sending units so I don't have to go back in. I've tried turning the car to the 'on" position for about 10 seconds without starting it to see if I could get the pump to load the line, if that's the issue, but it doesn't seem to make a difference.
The battery is good. It tested 12.5v after sitting over night.
View 9 Replies
The car died randomly and now it won't fire. I know it is getting fuel, none of the relays or fuses are bad. I am pretty sure it is not getting spark. The spark plugs that were in it were pretty much gone, put some brand new ones in and while testing I didn't see it spark. The wire resistance tested fine with my multimeter. I just checked the resistance on the coil pack. High side (set to 200k ohms) was ~15.6 on either bank, low side was 0.060-0.062 (set to 2k ohms, my meter doesn't go lower).
View 2 Replies
To start I was driving home the other night, car just stalled out and would not start back up, at all. Just cranks over and over. Things I have checked
- I am getting a spark from the plugs
- Fuel pump primes when key is turned on
- Fuel comes out of lines, even more so when key is switched over so pressure should be ok, I have not checked exact pressure due to not having a gauge.
- I have checked all relays under the steering wheel (just visual) some had brownish on the connectors and I cleaned all that off.
- All fuses are good and not blown (voltage meter also showed power coming to a few key fuses I checked.
I am down to a few things that I have read could be possible causes
- Camshaft Position Sensor
- Crankshaft Position Sensor
- Not sure what else to really check
View 24 Replies
I have a 2001 mustang convertible in good cond. A 6cly that I have had very little trouble with over the past year. I put in a new battery then, just after I bought it from a dealer. The dealer had gone over it with fluids etc. and I had a friend look it over when I bought it. He said it was very clean and a good buy. So, last week I started having trouble starting it in the morning. It would crank but would not fire. I turned the key off, and then tried again, Same result, cranks but doesn't start. I turned it off again and being worried about draining the battery, I turned everything off, radio, heat and fan, lights. Then I tried to start it again and, it started. I'm thinking I need new plugs, but I ignored the problem and went to work.
A couple days later I was leaving the grocery store, turned the key and same thing again, cranks but doesn't fire. I knew what to do. Turned off everything and tried it again, it started. Ok, so now some repair, possible plugs, is on my priority list. I need to get this fixed before the bad winter weather comes. Yesterday, after a long day at work, I was ready to go home and I it happened again. This time it's terminal. No matter what I did I couldn't get it to fire. This morning it's sitting in the office parking lot and I need to deal with this today.
Could be plugs, could be the fuel pump. Before I call the dealer and pay 4x what I should for this, what do you think it could be? 3.8 6cly. The car is sitting on a slight incline, in the parking lot. Gravity pulls fuel from the engine to the gas tank, if a fuel pump is going bad this could be why I can't get it to start. I'm going to roll it to a level area and hit it with starting fluid to determine if the pump is bad. I'll also pull a couple plugs.
View 18 Replies
My 2001 Accent GS (1.6L DOHC) wouldn't restart after a short 2 mile trip to a local store. The engine cranks fine but doesn't fire.
It has had a CEL issue for awhile and after it wouldn't start I checked the codes and got:
303
335
722
I replaced the Crank Position Sensor and Fuel Filter but it still just turns over.
I hear the fuel pump run when I turn the key on and I broke the fuel line and it is Pressurized, so I doubt it is a fuel issue.
The 722 code indicates the output speed sensor has an issue. Need to know definitively if that sensor is completely shot could this prevent the ECU from firing the engine?
I have had this car since it was brand new and I'd like to keep it going a little longer.
View 5 Replies
I just bought an 04 Ford F250 diesel 6.0 with 92k miles. Previous owner installed a UNGO alarm with remote start. Last week, after work, I started it using remote start. I got in the truck and realized I had forgotten something, so I exit the truck and leave the keys on the seat. Truck is still running. The doors lock. I reached in through the cracked window and pushed the unlock button. Here's the problem.. the truck died immediately won't start.. mechanic says it's the high pressure oil pump. I'm thinking it's the anti theft system but no luck.
View 1 Replies
I am having trouble getting my 2000 7.3 (200k) to start on the colder mornings. It will crank over fast, but won't start without a lot of tries. Today it took 6 pre-heats and cranks, but on others (and colder days) it has started easier. It does seem to be getting worse though.
I have replaced the glow plug relay recently so it *shouldn't* be that unless the replacement is fried. Starts fine the rest of the day and drives fine, but not in the cooler am (it was about 34 this morning). I also tested the batteries yesterday and while they aren't new, they tested okay.
Also, I read (briefly) about the CPS, but forgot to watch the tach this morning, but did notice it is pushing smoke out when turning over.
View 12 Replies
Friends truck, 06 with 135k. Problem he's having is, truck cranks over fine but doesn't fire, if he kick starts it, it fires right up. Haven't had the chance to put my AE on it, figured I throw it out there.
View 7 Replies
2002 7.3 Power Stroke... I bought the truck about 4 months ago and I absolutely love it but over the last few weeks is has been acting funny at times, it doesn't do it all the time but it has been getting progressively worse, ill drive the truck all day and no problems when I shut it off and go to start it again it just cranks but won't fire.
* Batteries are charged and in good condition, oil is a little dirty but full, I have no codes or check engine light on, and my wait to start light seems to be working fine!
* If I supply a fuel source(starting fluid) the truck will fire but not stay running
* And let it sit for 15 to 45 minutes fires right up like there was never an issue.
* There are no blown fuses
View 6 Replies
I have a 6 liter 2005 e350 diesel that starts great when cold and runs well all the time but after it warms up it just cranks but won't fire up. But if i shoot ether into the intake it will start. It doesn't show any failure codes.
View 2 Replies
While driving my 99 F350 7.3 it died and I was lucky enough to coast home. No WTS light, no tach movement when cranking, no fuel pump, no CEL, Cranks great but no smoke or fire. New CPS & PCM still no lights or tach. Moved relays checked all fuses. WTF is wrong?
View 14 Replies
My dad has a 99 F250 with a no start issue. Everything was starting and running fine one day. The next he gets a no start. Cranks fast and fine but wont fire up and start. He has a scangaugeII hooked up to it and his oil pressures and volts look fine. His tach moves when he is trying to start it. He checked the icp sensor and it had oil through it so he replaced it with a Ford part. Unplugged it and the scangauge pressure goes up but no start. He also replaced the ipr with a new Ford one just in case. He checked and is getting low pressure and high pressure oil.
I am having him check the fuel heater fuse #22 to make sure it is not blown. He had the block heater plugged in all night along with a battery charger to make sure they are topped off as well. We have gone through a couple of the checklists on this site for a no start condition but nothing has solved it yet. I think he is sitting at about 200k on the motor. No major issues or problems until now. He is currently also pulling the ICM to check it out as well. No codes are being thrown.
View 14 Replies
I just replaced the motor in a 2002 Sante Fe 2.7 due to timing belt breaking, this motor will not start, it turns over, but I am getting no fire to the coils. Crank sensor replaced waiting on the cam sensor, anything else it could be?
View 2 Replies
My wife owns a 2004 hyundai santa fe, and recently i replaced the belt and idle pulley, I've worked on a few cars in my life and understand the basics and some on how to work on a car.But this has me baffled, the other day i decided to take her car to work. She warned me it had a a slow turn over sometimes i told her okay and headed off to work, drove fine to work no start up issue, but then i went to lunch and it had a slow start like she said. Then in the afternoon started just fine for the drive home to work. I stopped at a gas station to put a little fuel in and the car wouldn't start, it would just release a small cloud of smoke from where the the starter was, so i said ah loose starter wire. That however isn't the case, pulled the plastic shield from the bottom off abd the heat shield off the starter just to find nothing was wrong with either instead its the wire above that running from the wiring harness to the motor, how to fix this issue? Ive attached a few photos
View 1 Replies
I have a 2001 Hyundai Sante Fe that died on me while driving down my street. The engine sounded like it was loading up for about 1-2 seconds, then it died. It turns over but does not fire.
After a little troubleshooting, I have no spark in cylinders 1 and 4. I swapped the two coils thinking that I had a bad coil, but then the suspected bad coil created spark on the 2-3 cylinder side. So both coils work.
I towed the car to the shop and the mechanic after about 2 hours of billed labor, he is leaning toward a bad ecu. He said there also is no fuel metering from two of the fuel injectors. He checked the resistance on the injectors and said they are fine. He is thinking it is a control/command issue. The car has many other unrelated problems and I am not sure I want to spend too much more money on it.
I am skeptical about a bad ecu. Or sensors that may be causing my two cylinder no spark and alleged fuel problem?
View 14 Replies
I have a 2006 Santa Fe with the 3.5l, AWD, 5 speed auto, and 65,000 miles. Its a daily drive. Out of the blue it won't start. It cranks, but it won't start. The battery is strong and it has 1/2 tank of gas. I figured my code reader would solve the mystery, but it's doesn't produce any error codes. With no codes I don't even know where to begin.
View 4 Replies
I have a 2004 Hyundai Santa Fe 2.4 L. Front wheel drive. Cranks over won't start, replaced crankshaft sensor & camshaft sensor, no spark. Where do I go from here?
View 1 Replies
2004 2.4L Sante Fe Base model. Car stalled out the other night, engine cranks but wont turn over. I have it towed to mechanic who tells me that the ECU is fried and they cant get any diagnostic done, that only a hyundai service can do this. I have it towed to service. Service tells me that they cant get a diagnostic done without a working ECU and that for the ECU alone. Then they could figure out what was going on with the car. The service also told me that the ECU isn't something that you can just go get at a scrapyard because it is specific to the VIN on my car. It just didn't sound right to me but I might be wrong.
View 7 Replies
a 2004 passat 1.8t 5spd came to the shop, cranks but does not
fire/run..i through the vas 5051 on there - p0688 - open circ. main relay...located this power supply relay and tested it - she had an open winding...replaced it runs excellent
View 1 Replies
My Santa Fe quit running one day as I was driving. The fuel pump hums when I turn the key to on. The spark plugs look ok. One coil is not getting a spark. We replaced that coil and it still isn't sparking. The timing belt appears to be fine. I bought an OBD II reader, and it gave me the code for the camshaft position sensor. We replaced that today, but there is still no spark. I cleared the code and tried to start the car. There are no codes present so I am assuming I fixed the camshaft sensor issue. Next up on the list is to replace the wiring leading up to the ignition coil. I gave it a quick look over. It appears to be ok, but I might replace it anyway. The outer housing is cracked a little, but the car is 13 years old so I expect that. Before it died there was an awful sound coming from the engine. It sounded like a piston was rubbing/scraping. I am throwing that out there just in case it is related to my electrical issues. I have noticed other weird electrical issues as well. The middle brake light usually works, but sometimes it doesn't work and sometimes only part of it works.
View 4 Replies
