Not sure if it did it last summer, but I have noticed that with the AC on when I come to a stop the RPM drops to right around 500 for a second and car has a light shudder (no doubt from the RPM being too low). Since it is only with AC on and for such a short time, is this a sign of something out of whack, or is it normal?
View 1 RepliesI have a problem with my 2004 Santa Fe, 2l diesel. Will try to keep this short!
When driving it suddenly 'heaves' (not sure how else to describe it), then it cuts out. I wait about a minute and then it restarts.
At first there was no 'heave' but there would be a momentary loss of power (I thought it was the clutch). Then it progressed to the 'heave' and then cut out, this happened now and then. Very quickly it started to do it every time I drove it. My neighbor mechanic blew down the fuel line, said the fuel pump in tank sounded ok, seemed to do it more when below quarter of tank.
So I kept tank topped up, it seemed ok, then on one 11 mile journey it did it 3 times, the last time the engine management light came on, crawled it home, after which it would not start at all. The computer said it was either fuel rail or coolant sensor. Neighbor replaced coolant sensor, it started ok. Tried it next day - 6 miles and it heaved and cut out again. This time no light coming on.
I've read about cam sensor, crank shaft sensor, fuel pump at back of engine...
My 3003 Santa Fe AWD has an issue with the blower fan. It stops, then starts working and clicking can be heard behind the dash when this happens. The clicking seems to increase when the climatization switch (the one that switches the air to the front vents, foot wells, windshield, etc) is turned off. When it clicks while the switch is on the off position, the blower blows for a split second every time the click is audible. It kind of turns itself on/off. Before I start replacing parts, I suspect the fan relay to be the culprit, but I'm not sure.
View 2 RepliesIt's my 2005, 2.7l. auto trans, FWD.
AC stops blowing cold when the engine temp get hot. As long as the car is moving, it blows nice and cold. Also, when sitting the engine temp rises quickly and will over heat if you don't get moving.
Cooler fan on the inside of the radiator never kicks over to high mode as the temp goes up. I checked the fuses and the relay and both are good.
That leaves me with a bad fan? Correct? Also, what is the part number of the fan?
The car started rough idling and a few weeks ago while driving "lost power" momentarily. I went to take a look at it and even just idling it will randomly drop 1000 rpm, or when the gas is one in P it does the same thing. also the dash lights dim at the same time.
I pulled these codes (below). I cleared the codes and tried to replicate with no luck. The car had been sitting in a parking lot outside for a few days and it has been -15C. I asked if it seemed to only happen when it was warm (the week before it was +10C) and they said yes. It has been another week (still cold) and the codes have not returned.
Quick google of these codes suggests maybe a throttle position sensor and/or loose battery connection.
I've been having trouble getting my 2001 toyotoa echo to start in the cold weather and STAY Idling. All I can do to keep the car going is hold my foot on the gas until it warms up, then it stays running, low idle, but running. It starts fine the rest of the day, but that first start in the morning doesn't take. The check engine light comes on and stays on, and the car seems to idle rough at stops.
At first the Mechanic I took it to (good guys) cleaned out my throttle body (physically and chemically) and this seemed to solve the problem for a couple weeks. I'm located in Toronto, Canada, and we're heading into cold weather and I just want a car that starts. It started up again recently and I'm now being told (on my second visit to the mechanic) that it's my throttle body/idle control and that this part needs to be replaced, to the tune of 627.00 + labour.
A couple weeks ago I had to have both lower ball joints replaced on my '01 XLS 4WD with the 6 cylinder engine. The garage's alignment machine was on the blink, so the mechanic told me to it woudl be fine to drive, and to bring it back this week when the machine was fixed.
The Escape seemed to drive fine until today, coming home from work, the Escape veered slightly to the right, and there was a brief sensation in the steering wheel as if it had been disconnected, as if something slipped. Then the steering was back, and although I was tracking straight down the highway, I noticed the steering wheel was turned to the left. It seemed to steer fine, although I had slowed way down.
Usually happens after car is warmed up. Rattles only while stopped and transmission still in drive. If I shift into Neutral or Park, rattling stops.
Last time I had a problem similar to this, dealer said it was a heat shield making the noise and they said they removed the heat shield (didn't specify what the heat shield was for.
Now I'm wondering if the heat shield was removed, what else this could be now...planning on taking it in in a few days.
I just replaced the crankshaft angle sensor, camshaft position sensor, starter and both serpentine belts (power steering and alternator, a/c belt). She fired right up, but now it won't sustain idle, she dies unless you keep the rpm at 1000. It almost seems like a fuel issue, but it's just a guess at this point. What to check next? Computer is throwing no codes at all.
View 4 RepliesJust bought a 2004 3.5 v6 Santa Fe 140k miles. It's my first 21st century vehicle, the first time I've had one so computerized and all that. I'm really unfamiliar with many of the sounds it makes and what not. This runs nothing like my old Camaro or Dodge, what's normal or not.
She really seems to rev pretty hard in idle, especially when braked at a light while still in drive. Is this normal for a Santa Fe?
I have a 2004 3.5 V6 that is making a rattling noise when the car is in idle and/or about 1rpm. Sometimes, for awhile now , it kind of screams when I first start it...but not all the time. I know this is a loaded question but what do you think it might be? The screaming noises don't happen all the time, like I said, and very rarely happen together but the rattling is happening a lot!
View 1 RepliesMy 2001 Santa Fe is having some major issues with rough idling, and there is a fairly significant oil leak. The check engine light is not on. In the past year it has had a new fuel pump, fuel filter, valve gasket covers, spark plugs, spark plug cables, and transmission.
View 2 RepliesWe just replaced the starter on a 2004 Hyundai Santa fe 3.5. The car now starts, but won't idle. I can keep my foot on the gas and keep it running, but as soon as I let my foot off the gas it dies. We didn't have this problem before replacing the starter. Where to start looking?
View 3 RepliesI just felt that my 2005 Santa fe shakes when idle in front of a traffic light today, later on the check engine light illuminated. Drove to a Monro shop right way and diagnosis using their professional OBD reader, it turns out that the Cylinder 3 and Cylinder 6 are misfiring according to the OBD scan result.
View 9 RepliesWhen I start it up it won't idle untill you give it gas to 2500 rpms and slowly let off the pedal to 1000 rpms to keep it running and itll stay running. When you turn it off you have to redo it all over again. The plugs and wires were replaced. It started doing it couple days after the back 3 plugs and wires were replaced. Just got the fuel pressure regulator replaced and it still wont start up without giving it gas.
View 6 Replies2004 Hyundai Santa Fe 3.5L for about a month has been sputtering/losing power when I come to a stop but keep it in gear. You can see the gauge drop when it sputter. Runs fine if I put it in park at the stop lights which I do because I feel as if may shut off (never has shut off). Replaced the crankshaft sensor and it had no effect. I so notice the same sputter when driving sometimes.
View 8 RepliesAt idle, (600 RPMs, might need to bring it up?) the motor is Real rough, but doesn't stall out, just very "wobbly" Once the car is brought up to the 900-1000 RPM range everything flattens out, and at driving speeds it drives great! Pulled up to 90 mph on the high way, and passed a few cars on some back roads and everything ran great, until I hit idle.
It threw a code for the Cam Position Sensor after I tried to restart the car, and the person who work on this car before me had zip tied the connector into the sensor because he had broken it. Low and behold, you cant buy just the replacement part of the harness.
I tried to get the wires all plugged back in, and the CEL went away, but the idle was still pretty rough. Also, at idle, the oil light flickers just a bit.
2003 Sante Fe is suddenly having a problem at stop lights or anytime the car is stopped with brakes. It feels as if the car is going to stall - or back fire. Very evident since it pulls on the brake pedal - just had back brakes replaced.
View 1 RepliesMy father owns a 2003 Santa Fe GLS with the 2WD 2.7L V6 engine.
Recently it has been having lots of power loss issues. It vibrates/misses when idling, if you put your foot down on the gas pedal, whether under load or not, it sometimes stalls or just sits there. We took it to Hyundai, and they had no error codes. They charged us $150 to tell us nothing is wrong with it, when clearly something is. The car has become downright dangerous to drive because it cannot make it up hills without stalling/losing power.
The most recent thing we had done to it was the wires/spark plugs changed, which I think was at 65k on the odometer?
I have a 2003 Hyundai Santa Fe. Within the last 2 months or so I have changed my timing belt, spark plugs, and all belts that needed to be changed. I notice that when I am idle at a traffic light, the car is a little rough or bumpy. Is this normal for its age, or should I be looking at something specific.
View 11 RepliesA few days ago, I started my wife's Santa Fe (106k miles) to warm it up and it had a rough idle. I gave it a test drive and the engine light came on and off a few times as it sputtered down the road. I retrieved the codes with my scan tool and it showed - P0300, P0304 and P0306. After some researching, I decided to change the coils, plugs and wires (under upper manifold) this coming weekend.
I have seen the web page instructions for doing this on a 2.7L [URL] .... but it has less stuff around the manifold compared to our Santa Fe. These instructions doesn't include coils was well since the plugs in front use just wires.
My question is.. Is there a set of instructions for the 3.5L for removing the manifold?.. From a less intense standpoint, maybe some of the hoses and cables can stay intact just to move the upper manifold or lift it to the side?... Also, Cyl 2, 4, 6 are the three sparks plugs in the front? 2004 Santa Fe 3.5l ....