I am trying to fix my friend's 03 Santa Fe 2.7L with 325K miles on it. Pulled the codes and he has misfire in #3, 6 and a random one. It doesn't do it all the time, and when it does do it he can sometimes shut it off and restart it and it will be fine.
What is the likely culprit causing the misfires and how to test it? He can't just throw parts at it.
2002 Hyundai Santa Fe 2wd 2.7L 175,000 miles
Having misfire in #1 &4, new plugs, new wires, new coils, new cam and crank sensors, cleaned and tested fuel injectors, checked injector signal, checked timing belt.
Swapped around plugs, wires and injectors(keeping same firing order) and the # 1 & 4 will not fire. There is spark to the wires and plugs and gas thru injectors but no detonation.
With plenum and exhaust manifold removed (front only) visually checked valves. Installed new oxygen sensors while exhaust was out. Tested ecu fuses in black relay box in engine compartment.
Engine stars first time ,every time but only runs on 4 cylinders. Check engine light code reads no 4 cylinder misfire.
I just purchased a 2005 Santa Fe, 4WD, 2.7l..the engine has a miss...the code that came up was "misfire in #2 cylinder"..I checked the coil pack...and the wire harness just crumbled..so I replaced the coil pack...reset the code..and it was good for a couple of days...I got through inspection...today I put on the A/C..and the engine got rough..the check engine light came back on..same code..misfire in #2..I'm thinking the injector or what else could it be? plug? wire?
View 3 RepliesI just felt that my 2005 Santa fe shakes when idle in front of a traffic light today, later on the check engine light illuminated. Drove to a Monro shop right way and diagnosis using their professional OBD reader, it turns out that the Cylinder 3 and Cylinder 6 are misfiring according to the OBD scan result.
View 9 RepliesI have a 2004 Santa Fe with the 3.5. Today I started it and the check engine light came on. It was not on before this. (We had a lot of wind and rain from the storm but nothing major.) And seems to be running fine. I went to the auto parts store and they ran a diagnostic and the Code P0306 came up #6 cylinder misfire. They said probably Spark plug, wire or coil for #6, then went to look up code in computer and did not have my truck so they went with Kia or Domestic, which gave different possibilities for a code P0306.
They had me buy some fuel injector cleaner as injector was on the list. The light is still on so I guess the cleaner was not the magic bullet. I spoke to a lady at another auto parts store who is a wiz when it comes to cars and has been around them and fixing them a really long time. She says the Code P0306 is Spark Plug, wire, coil #6. She has a 4cyl Hyundai car not truck and she had the code for her #4 misfire in the past and she started her repair cheapest first, Plugs, wires her code was still there she then changed the coil and that did the trick for her.
I on the other hand can't do this stuff myself. Can't afford the dealer anymore or to have a shop do a tune up AND coil if I don't need all new plugs and wires just a coil as they will charge a lot to do a lot all. And it may not need it or even be any of those things. I also suspect the dealer and shops will want to still hook up their computers to do an costly diagnostic because the light is on, even though I know the parts store already came up with a code P0306 twice. Spoke to the dealer on the phone and he already basically said they would want to do that first for $100 plus the cost of repair.
I brought the truck new. It now has 91,500 miles on it and the dealer has already done two tuneups on it in that time, Plugs and wires. I hear it probably shouldn't have even needed these tuneups in this amount of millage? So the last one was probably about 2 years ago and a few thousand miles maybe a guess 10,000-20,000 miles ago. Do you think a plug and wire would be bad already in that few miles?
I got a check engine light. I went to Auto zone to get it read & they came up with a P0303 - Cylinder 3 misfire. Since I bought the vehicle a couple of months ago, I don't know when the plugs were last changed, so I decided to change them. However . . .
Is there a secret to getting the plug boots & wires out of the hole and off the plug without wrecking the wires?
I have a 2002 Santa Fe 4 cyl that is giving me a problem that I could use some advice on tracking down & fixing . First & most important is a code P0302 # 2 Cyl misfire. How to check the ignition coil pack , injector ,& wire for this cylinder in home garage with normal tools & meter . Is there a you tube displaying how to do this step by step ?
The other problem which I don't have the code for at this time is that some part of the exhaust is not getting warm enough & this also put's the check engine light on . Will get back on this one when I solve the main problem Misfire.
I've had the plug wire for my #4 cylinder burn out twice in the last 6 months. The car started running like crap and threw a CEL, the code was for a number #4 cylinder misfire. When I pulled the wire it has obvious signs of being burned out, like white powder and burn spots near the base of the wire where it goes over the plug. The plug and coil both look normal. No issues with the other cylinders. What could cause it?
This is on my '05 Santa Fe, 2.7l, FWD auto, with 180k miles
I have a 2005 Santa Fe with the 3.5 with 112000 miles on it. I had the engine light come on with the code P0302 cyl #2 misfire, I got spark plugs, plug wires to do a tune up on it. I changed all of it and got it back together, started it up and it still had a miss to it. I then took the front spark plugs out and did a compression test on it. #2 was at 85, #4 was at 120, and #6 was at 160. I couldn't check the back cyls because I had already put the intake back on. I then did a wet test, and all the cyls came up to 160. So this tell me that the piston rings are bad in #2 and going bad in #4. I have kept all the oil changes up and up to this point I haven't had any trouble with it. Having this problem with there 3.5?
View 1 Replies2005 3.5L FWD. 5 days ago I left the house, the engine was running smooth at idle but having hiccups when accelerating. Check engine light went on when accelerating but going off at idle. Turned around at the first stop light, parked the car home and pulled code P0302 misfire on #2 . Figured it's most likely the coil, was going to order one next day but to my surprise, no more check engine light next day and engine has been running smooth since then. Probably drove 100 miles since with no issues. I have 6 spark plugs waiting to be replaced but it's too cold to do it right now unless it's an emergency. Car has 105k miles now, spark plugs were changed at 63k. Was this just a fluke and P0302 will probably not come back or should I not risk it and just go ahead and replace the coil? If I end up replacing the coil, should I do one coil or all three?
View 22 RepliesMotor missing has 61k. Code reader says # 3 misfire. got new plugs. 2 people say its probably the coil on #3. Its center in the back. Need step by step to replace the coil for #3 and plugs while I've got it apart and where is the best place to get a coil?
View 3 RepliesWe got our latest Santa Fe computer email and it warned of an engine fault. The car itself was not flashing any warnings though. Took it to the dealer and they said OBD was throwing a P0303 cylinder 3 misfire code. They shifted the ignition coil, and replaced the injector and seal before resetting the code. They had the car for 3 days though. Car was not running rough or anything else you would expect from this type of issue. Still trying to figure out why we got the email with no indication of trouble from the car itself.
View 3 RepliesI have a cylinder 3 misfire and the vehicle is idling rough so I took it to the deal because I have a power terrain warranty. They're telling me I'll need a new manifold and plenum, coil pack, plugs, and gasket. Could this be accurate? I don't want to get screwed over...
View 9 RepliesI own the 2014 Santa fe turbo 2.0 litre limited which has 4000 km on it. Within 210 km the engine light came on 3 times. I took it into the shop and they ran a code of P0303 which is a misfire, they changed the coils #2 and #3 and cleared the code. The second time it showed the same code but the shop said it was in the history so that is why the same code came up again. They ran an update ECM? and all was good. Now the 3rd time they tell me no code has come up and can't do anything about the engine (they cleared it) but it was like chasing ghosts. My vehicle runs great so not sure why I am constantly having this issue.
View 68 RepliesI have my timing belt and oil pump replaced and after 2 days the car was misfiring. Had the throttle body clean and reprogramed and still the same issue. run all test and its ok. What the issue will be. I was told it can be the ICM but the mechanic says there is no way to test it.
View 2 RepliesI have a misfire on 1 I recently changed intake and plenum gasket, changed plug, wire, injector, cap, rotor, compression check and pulled valve cover rockers moving good and I recently swapped injector wires on 1&3 only shows misfire on 1.
View 5 Repliesmy dad has a 2001 Passat and he recently had his check engine light come on. We had it checked by a guy who owns a tester (snap on) and it comes up with a misfire fault on cyl #2. Wire looks good, I didn't have tools with me so I couldn't take a plug out, but do you think it could be a bad spark plug? Bad coil? Car has 89K on it.
View 5 RepliesI have a 2001 ford windstar the codes are bank 1 lean (wires have been cut) could this cause the miss fire on the #1 and 3 cylinders? The previous owner put copper plugs in it instead of platinum. How hard is it to change the plugs?
View 6 RepliesNew to the VW world but I am not out of my element for I am a Porsche guy. So I feel right at home. Last night I picked up a 2001 wolfy Jetta with a 1.8t on the cheap with a misfire on cylinder 4.
I have verified I have no spark on 4. I have confirmed the issue is not the spark plug, coil pack by swap and see method. My coil pack and plug work fine on another cylinder. I reset my cels and here are the new ones that pop up:
a 121 - gas pedal position sensor- doubt this would give me a no spark
a 304- Misfire on 4, (duh, like I needed to hear that)
a 030- bank one 02 -Doubt this would also give me a no spark condition)
In my testing:
I have good system voltage on the coil pack
I have good ground ohms
My signal wire is not shorted high or low
When I take V and ohm readings on the coil pack connection, either with the ign on or off they are all in line with the other sensors. So I don't think I have a wire issue.
The PO had the ECU replaced at a local dealer. I looked at the old ECU and it appears it had got wet at one point.
Im wondering if the same thing hasn't happened to the new one. however after they replaced the ECU they gave him the car back still broken. So it never ran even with the new ECU.
1 Where is the ECU?
2 What tells the ECU to fire the coil packs at the right time?
2001 elantra 167000 miles, started a hesitation when given gas and check engine light came on. After hesitation rpms go up it runs good. Code is # 2 cylinder misfire. I have changed plugs, ignition coil and ran seaform into vacuum line and tank. Still no change. Could that 1 injector be clogged.
View 2 RepliesI have 62,500 on my 08 Santa Fe... never had any engine problems, but today, started the vehicle, drove 1/2 mile in town at 25 mph, turned a corner and the vehicle shuttered and lost driving power. At the same time, the check engine light came on and flashed continuously. I drove 1/2 block (around two corners in town) with the on/off studder and loss of power. I pumped the accelerator just to keep it from killing. As I stopped at the next corner and idled the vehicle regained power. I pulled over and called the dealership service department and they recommended I drive it home (blocks away) and turn the engine off, then try to restart it and if it started drive it 30 miles to dealership.
Did that, engine light came on steady and vehicle had full power. Long and short... the code was P0300 Random CYL Miss Fire Fault (random cylinder miss fire). After scanning the vehicle, test driving it and inspecting it as they do, they could not find a source of the problem or duplicate it. They cleared the code and promised that if it happened again they would credit me the $90 diagnostic fee I paid today for them to find nothing and apply it to a problem they couldn't find. They were willing to try and warranty it even though it is 2,500 over warranty if it had needed parts. Has this cylinder misfire happened to any of you? I've never had a problem like this really go away, so I'm expecting it will show up again. Also, they want to replace the timing belt (at 60K) as a preventative measure. What do you think? Can I wait till 80K?