Santa FE SM (2001-06) :: Idle Really Low / Almost Stalling And Oil Pressure Light Flicker When Warmed Up
Dec 2, 2015
I bought the car 3 years ago 2003 2.4L Hyundai Santa fe , I have driven it around 200 miles ( to and from shops ), I am having an issue now where once the car is warmed up ( post 15 mins ) It will idle really low * almost stalling * and oil pressure light will flicker, If I hold the brake and get it to almost 800 - 1k RPM it goes off and driving is not an issue *no knock*. I just got it driving for the 1st time in the past year, and drove it for about 45 mins in stop an go traffic, Temp light was all the way to cold, once stopped in stop and go traffic it would go up half way, as soon as I could get above 50mph it would slowly work itself all the way to the bottom?
More Information
2003 2.4L Hyundai Santa fe
I should really count my losses and move on but I cant.
Bought the car with 89K on it I now have 90K
New Battery
New Radiator
New Motor mounts 3
New Trans mount 1
New Hoses
Oil Change ( 40 miles ago )
Trans Oil Change ( 40 miles ago )
Power Steering Fluid change ( 40 miles ago )
2nd cat delete ( didn't want to waste any more money )
After Market 1st Cat
View 2 Replies
Advertisement
I picked up an 02' accent, 1.5l that i've been intending to use as a commuter car. Drove fairly well on the way back home, but it seems it's got some low oil pressure issues once it's good an hot. As the oil pressure light will occasionally flicker at idle, mind you the car is near dying too.
Or so I thought, it was also misfiring/stumbling fairly badly,
Pulled all connections, cleaned, dielectric grease on them, fixed some of it. And it turns out the fellow who did the timing belt last didn't exactly remember to put the bolts back on the fuel rail.... Okay, that's fixed now.
Put in a little heavier oil, and no more issues with the light coming on, but I do have some lifter noise it seems like.
As well, the car will not rev past 5k in neutral or under load. Air filter is new, and no obstructions through to the intake manifold.
I'd guess based on the missing bolts here and there, the guy was a bit of a hackjob mechanic and i'm guessing has the belt out a tooth or so.... I can't see anywhere to stick a timing light on to verify ignition timing, how to check the timing belt is straight up? It's a bit of a dog compared to the other accent i've been in. The power band is like 2000-3500 and it just won't climb anywhere past that.
View 7 Replies
100k 2.0D .... Recently when pulling up at roundabouts or junctions either at low speed or quite rapidly, the engine oil light flickers. This doesn't happen at all on idle no matter how high it is revved and never while speeding up or at high speeds. I have tried to narrow the time it happens and just ended up being confusing because it can happen slowing down while in gear with engine under strain or to a lesser extent while coasting with g/box in neutral at idle speed.
The engine oil and filter has been changed but to no avail (as expected). I could check the oil pressure sender and wiring but it doesn't make sense as why the fault is not sporadic and quite consistent when it happens. (Also I did look at trying to remove the sender unit and possible fitment of a pressure gauge but how the *BEEP* do you get any tools to that!). I did mention it to a friend who knows a pair of mechanics at a local garage who both straight away went *ooooh sounds like big end bearings!!*
View 2 Replies
Had the following problems with my 2009 Santa Fe: Audio system would randomly reset when playing MP3 from USB drive, Headlights would dim/flicker when bakes depressed, LED lights on dash would flicker, random stalling while driving. Finally just died and would not start. The Hazard lights would not work only a bit of buzzing from the relay. Checked Battery, connectors, etc. All looked good. Measured voltage at fusebox (inside) and found it dropped from 12v to 4v when I put the hazard switch on. Showed there was a connection problem of some kind.
Finally used a jumper cable from the battery negative terminal to an ground point inside the cabin. Bingo that fixed all the problems, car started, lights were good, hazards worked. As a permanent fix I ran a wire from where the negative terminal of the battery connects to the frame, then drilled a hole in the firewall and ran the wire into the cabin. Connected the wire to a ground point in the cabin. Used a heavy gauge stranded wire. you can try this out with lamp cord as a temporary fix, but I'd use something heavier for a permanent fix. All problems have gone. No flickering, no stalling... This may be a problem on other models from what I've read in some forums (unexplained stalling - check the grounding in the cabin..).
View 2 Replies
My coworker is giving me a clean 2001 Santa Fe with 151000 miles. It was running fine then all of the sudden it lost power but was able to stutter home. I went to check it out it started fine but idled a little rough. When I revved the engine it rose to about 2500rpm and stuttered then stalled. Kind of like it was rich and choking out. It then had difficulty restarting.
View 10 Replies
Trying to get my daughters Santa Fe going. Engine stalling. Idles very slow. 2001 model with 2.4 engine, auto trans.
Code P0102 is active. Cleared with scan tool and it comes right back.
Replaced the MAF and no change.
Checked the intake for leaks / vacuum leaks and none found.
Checked for debris up-stream from MAF and all is clear.
Air filter is clean and dry.
Checked harness plug and found the pin 5 has 4.6 volts on it from PCM. This is the signal wire from MAF to PCM. 4.6 volts is KOEO.
IS THIS NORMAL OR IS PCM BAD ??? All other pins / voltages on harness plug are normal.
View 4 Replies
I'm having continued issues with my mom's POS 2005 Hyundai Accent. It usually runs great cold, but once it's warmed up, it will stall out while driving. This almost always happens when accelerating from a stop. After it stalls, you have to let it set for 30 seconds to a minutes before it will start again. It will also sometimes idle roughly.
I've changed out the TPS and the MAP sensor, the battery, the CPS, the fuel pump, and the spark plugs. I did find that the radiator bypass hose was leaking on to the wiring for the O2 sensor. I fixed that, and the wires appear to be fine. I've sprayed throttle cleaner around the intake and can't find a leak. I scanned the ODB codes and I'm getting a Random misfire, misfire on cylinders 1, 2, 3, and 4, the Throttle Position Sensor and the MAP sensor, both of which have been replaced.
Tonight during my troubleshooting I was trying the wiggle test on the various connectors and got zapped when I was wiggling the coil pack connectors. Is that normal? I'm starting to suspect a wiring or electrical issue, but I'm not sure how to troubleshoot that.
View 28 Replies
I have now had the first major issue with my 2012 Santa Fe 3.5L AWD. It started out with an intermittent low oil pressure light coming on at idle. As I researched I found the Oil Pressure Switch thread:
Oil Pressure Switch Replacement - 2010 Santa Fe 3.5L
And using that information I proceeded to replace the switch and while the switch had obviously failed unfortunately that didn't fix the problem. I tore everything down a second time to make sure the replacement switch hadn't failed and to make sure it wasn't leaking. Turns out that everything looked good yet the oil pressure light was still coming on after everything was warmed up.
Tonight I tore everything down for a third time to put an extension hose on the oil pressure port so I could hook up a mechanical pressure gauge in addition to the oil switch. While I am very pleased with how the extension hose worked out, however it appears that I do indeed have low oil pressure. Without letting it warm up completely I was dropping down below 15psi.
I guess at this point my best case scenario is a malfunctioning oil pump and worst case is worn bearings. With only 67k miles and fairly religious oil changes I am praying for the oil pump. My next step is to contact the dealer as I am still under the powertrain warranty, hopefully that goes well. I will try to keep this thread updated as I learn more. Up to this point I have really enjoyed the Santa Fe and have had minimal issues with it.
View 5 Replies
I own a 2004 Hyundai Santa fe with 40k miles on it. I drove it to Vegas about 2 hours ago and noticed that about every 6 minutes the headlight would kind of flicker. It was pretty constant the whole trip. There are no other lights that flicker, it's only the headlights. Is this a known problem?
View 5 Replies
Last weekend I decided my brothers 850 T5 was well over due an Engine oil and AFT change (two years for oil and never for the atf). The car has done 182,000 and drives great. Any way I bought 20 litres of 15w-40 and 20 litres of DEX 3 atf as it worked out a lot cheaper and it can be used for my fathers 940.
Anyway on Saturday I got the engine warm and noticed the oil pressure light flicker on and off. it had never done that before so I should have checked the dipstick there and then but I just went ahead and drained the old oil and removed the filter. To my surprise only about two litres of black oil came out despite the fact my brother swears he checked it 2 weeks before and it was fine. I thought this was odd as the engine had been running perfect and at that level I would expect serious damage to have been done. I fitted the new filter and sump plug with washer, filled a 5 litre tub from the bigger 20L tub and poured in 4L. I checked the dip stick and it took the remaining litre to get the level correct. I checked it again and then started the engine to get the oil into the filter etc and the level was still perfect. I finished the atf change(that's another story) and thought it a job well done.
The next evening my brother was about to use the car and I said I would check the level one more time now it was cold. There was nothing on the dipstick. There was no oil under the car so I slowly topped it up but nothing showed on the stick. I knew there was at least 5 litres in there so I didn't want to over fill it but when I started it, it sounded tappety. I put another couple of litres in and the noise reduced but still nothing on the stick. he then drove the car for a short journey and it drove fine but I said it was still tappety. I checked the oil again and now the handle snaps off the dipstick.
I have done oil changes many times before and am really very competent mechanically (I'm an engineer). Any way this gets me doubting the dipsticks accuracy so I suggest he let our neighbour who's a mechanic take a look the next day and basically today he came back and said he drained the oil and there was only 2.5 litres of oil in the engine. He topped it up and it's running fine and I fixed the dipstick with glue to check and it's perfect there as well. The thing is I know that I put enough in there, and my 20 litre tub has only 10 left.
The car is fine now. I know the obvious ones are that it was my mistake and I didn't put enough oil in, or I don't know the difference between a 1 litre and 5 litre tub but I assure you that this wasn't the case. Is there any where internal this quantity of engine oil can leak to? the transmission? coolant?
View 4 Replies
1991 Celica ST 4A-FE automatic, 238,000 miles, son's car, has been running great, until he says his oil light occasionally flickers on him. Car is in Wisconsin, driven maybe 2 miles one way to work every day, hasn't been on the highway is a couple months. Has synthetic 5W-30 oil with about 2,000 miles since last change.
Brought the car into the garage. Sure enough, after engine warmed up and idle got below 1,000 RPM, oil pressure warning lamp would come on. Engine sounded normal at idle and fast idle. Tough to put a mechanical pressure gauge on this engine (after to remove the alternator and A/C compressor and bracket, per the service manual, to access the oil pressure switch). I drove it on the highway, put about 40 miles on it, ran great, until I exited the highway. Anything below 1200 RPM, oil pressure warning light would come on.
Came home, removed the oil filter with intent to change it (to make sure it wasn't plugged). Smelled of gas. Oh-Oh. Drained the oil (oil level was at full mark, unusual for this vehicle, normally would be 1/2-quart low after 2,000 miles - 2 months of winter driving). Oil came out with consistency of water. Smelled of gas, and could see water droplets as I switch the drained oil from a collection pan into a jug. Thought was many short trips caused oil to never get hot enough to burn off unburned fuel blow-up or accumulated moisture, so oil was diluted, much too low viscosity.
Changed oil & filter with synthetic 5W-30 & Purolator PureOne oil filter. Took it back on the highway for 40 miles again. Highway drive was fine. Upon exiting, oil pressure warning light came on at 1,600 RPM or below. Oh-Oh. Had another 40 miles on the highway to get home. Highway drive was good again. Upon existing, oil pressure warning light came on again at 1,800 RPM or lower. Oh-Oh.
Worrying that the oil pump for pressure by-pass valve or of bearing spin-out or extreme wear (although engine sounded fine all the time), decided to order an OEM oil pressure switch. Had to take some of the bolt-ons off to access the oil pressure switch, but not all the service manual said had to come off. Took the old oil pressure switch out - looked just fine. Installed the new one, put everything back together. Checked to make sure the oil pressure warning light still came on with key in the ON position (it did), so I knew the wiring connections were good. Startup was fine (cold engine). Took it on the highway for 40 miles, after exiting highway, no more oil pressure warning light. Even tested the situation with the automatic in drive, brake applied, lights on high-beam, heater fan on high, rear window defroster on (got the engine down to 600 RPM), still not oil pressure warning light. Turned engine off, then turned ignition key to ON, oil pressure warning light comes on like it should.
View 5 Replies
For the past several months, I've noticed a gradually worsening flicker in my oil pressure indicator light. The light is off if I'm accelerating or downshifting for a pass or a hill climb, and it also goes off when I'm coasting or de-accelerating.
It's never steadily on, sometimes it's just barely visible, other times its flickering, fading, and brightening, but never at full brightness. It doesn't matter whether I'm at highway speed or at a slow speed, it's only a change in rpm that makes it go out.
I'm hoping, hoping, hoping that it's a problem with the pressure sensor, and not with the oil pump itself. Does the oil pump tend to fail gradually like that, it is it more indicative of a sensor problem? I'm hoping the latter, because replacing the pump is a major undertaking, one that I doubt I would do myself.
View 2 Replies
We got a 1990 celica gt with the 5sfe in it. first night driving it after about 30 minutes the oil light would flicker at idle. We checked the oil, it was nasty so we did a complete oil change. Didn't fix the issue. Well then we developed an oil leak at the oil pump seal so we replaced all those. We had heard the sending units were notorious for going bad so we took it out and put an aftermarket gage in it. Still an issue.
Ok so then we checked the main bearings to make sure they were ok, they are fine. Normal wear. No clogged oil screen either. We then was told to try a little bit thicker oil so we did that. Still the issue. Here's what happens. start it up cold at idle is about 50-60psi. Let it warm completely up and it drops to 18-20psi. When you rev it up it rises.
Ok well after driving it for about 30 minutes after warm when I came to a stop it dropped to 0! Rev it up and it rises a lot. Held it at 2k rpms and it stays at about 30-35 psi. Ok as I'm driving it, it has good oil pressure. Motor is not making any noises other than the common Toyota valve chatter.
We have ran cleaner thru the engine thinking so gunked up ports and still no change. We are at a loss. Like I said cold it's fine, revving it up after being hot is fine. Driving it is fine. but boy when the engine is hot n u come to a stop or at idle it's nothing.
View 9 Replies
I am after to find which USB cable and software can be used on my wife's ... 5/05 v6 Santa Fe to check the error codes. The car is revving up and down when cold and lacking power when warmed up, I'm guessing it's a sensor but I need to find which one.
View 1 Replies
Recently started experiencing a hard downshift after driving for 30 minutes, and only from 2nd to 1st. No other shift issues with other gears, up or down.
When moving over to manual shifting, it doesn't appear to have the issue when downshifting in manual.
I replaced the radiator about 2 weeks ago due to a serious leak, and the shifting problem wasn't an issue before as I would have noticed.
Going to start with the fluid lvl, but it feels odds with it occurring during the downshift to 1st.
View 5 Replies
My problem is my 2001 Santa Fe petrol 2.7 L its done over 300,000 km one day it sounded like a click when driving, then when I started it cold in the morning it was missing [not running right] and had no power until it warmed up the spark leads are not that old anyway I put new spark plugs in it it seem to run a lot better but seems to be down on power on hills I think coils are ok? the motor not smokey but burn little bit of oil.
View 10 Replies
At idle, (600 RPMs, might need to bring it up?) the motor is Real rough, but doesn't stall out, just very "wobbly" Once the car is brought up to the 900-1000 RPM range everything flattens out, and at driving speeds it drives great! Pulled up to 90 mph on the high way, and passed a few cars on some back roads and everything ran great, until I hit idle.
It threw a code for the Cam Position Sensor after I tried to restart the car, and the person who work on this car before me had zip tied the connector into the sensor because he had broken it. Low and behold, you cant buy just the replacement part of the harness.
I tried to get the wires all plugged back in, and the CEL went away, but the idle was still pretty rough. Also, at idle, the oil light flickers just a bit.
View 6 Replies
Our 2001 Passat wagon 4cyl turbo automatic has a random idle stutter. When sitting at a stop light the RPM's quickly drop and then regain idle. It happens at random times and only when idling after the engine has warmed up. It doesn't seem to matter if its in drive or park. What sensor could be failing or a possible cause? Over the past year the problem has increased from almost never to a few times at every stop light. My OBDII reader shows no codes. Car has 105K miles and I cleaned the throttle body.
View 2 Replies
I have a 2003 Hyundai Santa Fe. Within the last 2 months or so I have changed my timing belt, spark plugs, and all belts that needed to be changed. I notice that when I am idle at a traffic light, the car is a little rough or bumpy. Is this normal for its age, or should I be looking at something specific.
View 11 Replies
Bought a 2001 from a used car dealership about 2 months ago. A week later it started acting funny. It would often race the rpm's about 2000 when at at stop light and then others times would act like I was out of gas when I would take off. Sputtered and then finally run normally. Then other times it wouldn't start and just crank over and over. After 10-15 times it would fire up and then act like nothing was wrong. It was a total crap shoot whether it would start or not each time.
Took it back to dealership and supposedly their mechanic installed a new fuel pump. Ran like a champ for about another two weeks and then exact same symptoms started showing up.
View 7 Replies
Yesterday as soon as I started my car, I noticed a high pitched whining noise. As I drove, it seemed to stop, but as I slowed down and idled, it came back. After driving a couple miles, the battery light came on, so I turned off the AC, radio, and lights and it went off again, but as I sat at stop lights it would flicker on and off again.
View 4 Replies
