Santa FE SM (2001-06) :: Grinding Noise In All Gears At 3500 RPMs
May 14, 2014
Codes currently on ecm: P0134, P2125, P1174, P0735 My 2003 Santa Fe 2wd 3.5l with 160,000 miles was driving fine, then all the sudden whenever I reach about 3500 rpms there's a grinding noise that sounds like its coming from near or in the automatic transmission. As for the codes: P0134- I just replaced the o2 sensor with an oem part from autozone, so not sure why that's popping up. The connections look fine. P2125 and P1174- I'm trying to figure out whether the accelerator position sensor or throttle position sensor needs to be replaced. I have a multimeter but don't know if that will be able to tell me which one is out. The P0735 gear 5 incorrect ratio and grinding noise at 3500 rpms is what I am mostly worried about though. Could a transmission flush work with that?
View 2 Replies
Advertisement
So, I recently got my car serviced with balance shaft belt, 2 idlers, crank sensor, timing belt, spark plugs, ignition wires, and ignition coils. And now when i drive my car and accelerate it to about 3400 to 3500 rpm i get this rattling noise from my engine then when the rpm surpass that range i dont get any noise anymore. I really don't want to take it back to the shop and have to be charge for a diagnose but I am thinking it could be serpentine belt or loose of the down pipe.
View 6 Replies
I have this problem with my 2001 Santa fe 2.7 Lt auto done 326,000 km no power on hills sometime want rev past 3500 revs and sometimes will rev past this, it seem to get worse when fitted new fuel filter in the tank? have put new filters and O rings in injections, have just fitted new coils and the cat has no restriction. Starts first time but did have trouble the auto would not start in park until pulled top cover and got it out of park and started it in neutral changed the trans fluid and seems to move through the selection better. Could it be the fuel pump??
View 4 Replies
My 1994 Acura Integra makes a buzzing noise exactly between 3000 and 3500 RPMS. It sounds kind of like the sound a circular saw would make cutting wood. It only happens when I am accelerating through that range. Also, sometimes after driving for a while, it doesn't last as long and the noise stops around 3300 RPMS. I've checked the heat shield and it seems to be fine so I don't think its that. What this could be caused by?
View 3 Replies
What could it be? Replace front brakes. Then they said it was front axels, replaced them. Making same noise... grinding and feels like you are hitting brakes when you are not. Sounds like metal on metal. What else can it be? 01 sante fe 180,000 miles v6 awd. It was doing it in reverse but after all of this now just in drive at slow speeds.
View 3 Replies
I've got a couple of issues with a 2002, 2.7ltr v6 santa fe first off when taking off steady the car runs fine but taking off quickly it seems to lack power until it hits around 3000-3500rpm est then it takes off fine and all threw the upper rev range the auto seams sluggish but I'm not shore as I haven't driven another 2.7ltr as a benchmark. No error codes are present.
The second issue I brought a new keyless remote for the car and looked up a thread on how to program this they had reference to a set switch behind the fuse box behind the lower dash panel I went looking and found what I think is the remote receiver it has what is like a antenna cable plugged into it but no set-off switch at all is there any way to get this new remote programed or will it have to be done threw dealer or is there something I would be missing?
View 9 Replies
I own a 2.7 L v6 Santa Fe, 2004 with almost 50k miles on it.
When I accelerate and hit approximately 1.9k RPM I can hear a light grinding noise underneath the car. This happens both in 2nd and 3rd gear. So as it's accelerating up I can hear it, and when the car shifts up and the RPMs drop it will make the noise again as it passes through the same RPM range.
The noise is always there at 1.9k to approx 2.1k RPMs.
Also of note is that the sound is either gone or significantly reduced after driving around for a while. I don't notice it after freeway driving, for example.
View 2 Replies
I have a 2002 Hyundai Santa Fe v6. I've had problems with the air conditioning in that it blows hot. Paid around 900 bucks to have a new compressor installed because the mechanic said that would fix it but it didn't. That was about 8 months ago. Still blowing strong but no cold air. About two weeks ago I took the car to a different mechanic who told me it needs a new compressor which would be 900 bucks. I declined that but had the guy do a little work on the breaks. He put new rotors and pads on the front brakes two weeks ago. Now within the past couple days when I start the car up it makes an extremely loud nasty grinding type of sound for a couple seconds then stops. Oil is fine and new. It happened this morning long enough for me to look under the hood and see the fans looked like they were fine, and the loud grinding noise seems to be coming from behind the glove box. It hasn't broke down on me yet, it's just really obnoxious and embarrassing with all the noise every morning.
View 8 Replies
I am hearing a grinding noise when I turn the wheel to the left.. and when I straighten it again the noise goes away.. no noise at all when turning the wheel to the right. what could it be? 2006 Hyundai Santa Fe / 205,000 km's
View 4 Replies
I have a 2005 Santa Fe 2.7L engine. Right now it seems to be making a funny grinding noise in the passenger side. It's driving and shifting fine. Wheels seem to be ok. Once it cooled down the noise seemed to go away.
View 4 Replies
2004 Santa Fe, after starting car the brakes make a grinding noise, the nthe ABS, ESC and 4 wheel drive light come on. After the initial grinding the noise stops and the brakes work fine. Just the lights stay on.
View 4 Replies
My daughter asked me to look at & listen to a horrible grinding noise coming from the upper right area of her Santa Fe's rear hatch. There was a plastic grinding noise coming from THIS:
It's the lock actuator for the rear hatch.
Sometimes it works.
Sometimes it doesn't.
Sometimes it makes that horrible plastic grinding noise.
View 4 Replies
I've got a 2001 Honda Civic, automatic, that has a nice (what I think) belt squeal going. It seems to happen when it's wet/cold, in the lower gears/RPMs, when the defroster and/or rear defroster are on. SOMETIMES it will stop when I turn off the defrosters. If it persists I can make it stop by quickly putting it in park (at a light or stop sign) and right back into D or if moving gunning it for a few seconds. Occasionally I do get a hot rubber smell (like a burning vacuum belt) coming through as I accelerate. So as someone with no real car knowledge, does this sound like a belt issue that I can take care or myself (i.e. belt tensioner and a gauge) or should I just leave it to the pros?
View 2 Replies
I am hearing a rumbling noise when I hit 4000 rpms on all gears worst in 2nd and 3rd.... I just recently replaced the timing belt, TBA Done, valve cover gasket, and passenger side axle (through raxles). Anyways I started hearing noise after those repairs, my mechanic has gone through all the work recently done and cant find the problem..... We replaced the tranny mount thinking it was that, but no luck.... I have not lost boost, and noise starts 4000k and goes away at 4700k No codes are flashing.
View 5 Replies
2003 Nissan Xterra 2.4. It grinds when I shift gears, gears through 2nd thru 5th.
View 8 Replies
I am trying to get some advice on a diagnosis for a transmission problem i'm experiencing with my vehicle? It's a manual transmission and the sound i am hearing is when i shift gears is a loud whirling grinding sound. It's really loud in 2nd 3rd and 5th and doesn't stop.
View 1 Replies
Wife's Santa Fe has an issue with it's shift points. Its a 2002 with 148K on it, never has had a CEL, fluid is changed every 60K. Over the past few months the time it takes to shift through the gears is getting longer. What I am describing is not an actual delay between the gears, but rather how long it is starting to take to get the tranny to even shift. Sort of like how a vehicle shifts through its gears when your at a stop, and put the pedal to the floor and just hold it. it makes no difference if your barely on the gas or half way down, still takes a way longer time that it should to shift. It is slightly worse when cold, but still does it when warm. Is there some kind of temp sensor or vacuum line or whatnot that would cause something like this? When it does finally shift, its normal, tight, no slippage or delay. truck runs great other than this.
View 7 Replies
I made a mistake, detached TPS from throttle, thought it was purge valve, then I put it back and today my car won't change gears, I messed something up, never had problems with my transmission. Santa fe 2003 3.5 ....
View 2 Replies
My buddy's 2001 7.3L F350 has had 3 transmissions. Rebuilt and used. Once the new trans is in he goes like 15 miles and then is starts shifting hard and grinding gears. What this could be?
View 8 Replies
Symptoms- won't rev over 3000-3500 rpm's, upon acceleration (especially uphill) seems to struggle and won't accelerate much at all, seems as if trans changes fine. BTW, throwing no codes at present.
What I have already tried...new air filter, new fuel filter, had cat. check (was told stopped up but when removed found it was not and truck did the same even with cat. off), o2 sensor (upstream) replaced, battery disconnected to reset computer.
After reset of computer, runs a little better but still not good. Seems to start if you accelerate to quickly or when truck reaches around 40-45 mph.
View 11 Replies
I have a '96 Saturn SL with a 1.9 SOHC. I recently removed the engine and transmission to change the clutch. I also changed the timing chain guides, the valve cover gasket, the timing chain gasket, oil pan gasket, front and rear crank seals and motor mounts. After I put it back in, it revs to 3500-4000 rpms and is very rich (so rich it smokes). I replaced the throttle position sensor since it had a crack at the plug and to see if that was the problem. I have looked at everything again and nothing is jumping out at me.
View 10 Replies
