2002 My friend's 2.7L sante fe crankshaft position sensor went bad and I went to replace it. Removed bolt, it was stuck fast, tried to pry out and it broke off leaving the last 1/2 inch stuck in block. Tried drilling a hole in it and using a screw to get it out but no luck. Afraid to keep drilling that I might damage something behind it. How to get it out?
View 9 RepliesAfter heavy rain yesterday my 2005 2.7 Santa fe wouldn't start today. Had it towed to nearby dealer. The crankshaft position sensor needs to be replaced. He claims its melted to the block and oil pan needs to be dropped to remove it.
View 5 RepliesI am having a problem with my 2003 Santa Fe I have taken it to have the check engine light codes read and I have a code for the crankshaft position sensor, random misfires, something with gear 2 and 3 (not sure what it was exactly) it makes a loud noise when in 1st and 2nd gear when I shift out of 2nd the noise gets less and less until its gone and then does not come back until the car sits for a little while and cools down. Its running rough and does not have any power when accelerating. I had the timing belt changed a few weeks ago and it started running funny shortly after. I don't think the guy that did the timing belt knew what he was doing because I had to have someone go behind him and tighten the pulley.
View 3 Replies33k Civic 2001 "PO335 Crankshaft Position Sensor A circuit" error code
My Civic 2001 LX (non vtec 1.7) threw an error code today. It was, "PO335 Crankshaft Position Sensor A circuit" error code. It was raining a lot today, and this is the first day that it did it. I have never had this problem before. When the error code came on the engine automatically lost power. I couldn't get the car over 3000 rpm. Then it stalled in an intersection. Now it won't start period. It only has 33k on the clock.
The timing belt was done about two months previous, but i haven't had one problem until today, when it was raining.
My Civic 2001 LX (non vtec 1.7) 33k threw an error code today. It was, "PO335 Crankshaft Position Sensor A circuit" error code. It was raining a lot today, and this is the first day that it did it. I have never had this problem before. When the error code came on the engine automatically lost power. I couldn't get the car over 3000 rpm. Then it stalled in an intersection. Now it won't start period. It only has 33k on the clock.
The timing belt was done about two months previous, but i haven't had one problem until today, when it was raining. So much for a reliable honda.
2000 jetta vr6 manual 150k miles, i have trouble starting the engine so I thought i'd start by replacing the crankshaft sensor. I notice that its wet with oil when i pull it out, and wasn't sure if tits supposed to be dry. I may have a bad ECU in the end...
View 1 RepliesMy car doesn't start right now and a shop diagnosed it as an ecu, but I'm starting to think that is not the case. The tach doesn't move when I try to start it and pushing the gas doesn't change it, so I'm thinking it is the crankshaft position sensor. Unfortunately, down at school, I don't have access to a jack, so I was wondering if there is any way to get to the cpa without a jack? I'd rather not have it towed to another shop.
Also, my coil pack has a huge crack in it. Could that be causing my problem? And my sai has some really frayed wires and I'd rather not replace it if I don't have to because these repairs are really adding up, but could that be causing problems too? it's not causing gas mileage issues and I live in an emissions-free county, so simply not allowing me to pass emissions isn't a problem.
Looking for a picture or description where this sensor is located? I assume very close to the crank pulley, but I'm hoping I will not need to remove the crank pulley to gain access to this sensor. I have a 2011 Sonata, 2.4L engine.
View 3 RepliesI need to replace the crankshaft position sensor. On my 2002 Grand Caravan Sport 3.3liter. Where it is in laymans terms.
Is it better to approach from the underside Or from the hood side? I will know it when I see it but I haven't seen it yet!!
I have a 2001 Chevy Silverado 4.3L that I recently put a new engine in. The new engine will turn over but will not start. I am not getting any spark for some reason. The OBD2 code that keeps coming up says that the crankshaft position sensor is out of circuit. I have put in a new CKP sensor and new electrical connector, new spark plugs and wires, new distributor rotor and new ignition coil and still get the same OBD2 code and it won't start.
View 2 RepliesI got a 2004 Nissan Sentra and a p0335 (Crankshaft Position Sensor) popped up on it after the car stalled out sitting in a parked position for 2 mins. The car also stalled out again 20 mins later while I was driving. When the car stalled out in park I had to wait 3 mins because it was just cranking over, when it stalled while driving it started 30 secs later with 1st turn of the key. This car has been having start up issues after the car been driven and sat for 40 mins but when the key is cycled 3 times it starts up fine. I also was going to eventually make a post of this, the car been making clicking or rattling noise at times, off and on mainly when the car been warmed up and at idle more noticeably heard , hear the noise better from inside the car, forgot what side of the engine where the noise is coming from. Also I did a search in the past about recalls on this car and there was a recall on the CRANK ANGLE SENSOR on the 2.5L engines, the car I have is a 1.8L. Stated on this link 3rd one down. [URL] ... . Does it sound like the Crankshaft Position Sensor needs to get replaced?
View 19 RepliesMy son has a 2007 jeep compass 2.4l engine. He needs to change the crankshaft position sensor. Where to find it? He got a pic from autozone but you can't tell where it is on the engine.
View 7 RepliesMy wife's 2003 Altima has been stalling. The MIL came on P0335 Crankshaft Position Sensor Circuit. I did a little research and it seems that it is pretty common for that sensor to go bad, so I bought a new one. The problem is I can't get the wires off the old one. It is in such a ridiculous place. There is no line of sight anywhere. It has to be done completely by feel. Supposedly, I should be able to push the button until it clicks and then remove the connector. When I push the button, it definitely clicks - but it doesn't stay clicked. It clicks right back out before I can pull on the connector. How can I keep that button clicked in when I can't see anything and I can just barely get one hand down in there?
View 19 RepliesI have searched and have not found any information on replacing the throttle position sensor. My Santa Fe was running normal. I changed my tp sensor and how it limps along. When I loosened the old TPS, not even removed it, I heard a noise inside the TPS. When I replaced it I adjusted the TPS to read between 9 and 10% on my reader. But when I push on the gas pedal with the key on position the percentage doesn't move. Also when I drive it now it limps along and does not accelerate.
View 2 RepliesWe bought a 2006 Hyundai Sante Fe with the 3.5L and 4 wheel drive about two months ago, it has 94,000 miles on it. It was purchased from a dealership, and they had to work on it for a month before we took it from them because of some lights that were on, resulting in some sensors being replaced. We had it about a month when we took it to the grocery store, when we came back out I started it and it made a terrible noise, but was running, I immediately turned it off. Upon further inspection, the main serpentine belt had snapped, causing some damage to the secondary belt. We towed it home and I began to fix the belts.
When I pulled off the passenger side wheel and access cover, I noticed the remains of the belt were stuck behind the harmonic balancer, I tugged on it with about 5 pounds of force, and the entire pulley fell off of the harmonic balancer. I'm not sure if the belt stacked up behind and pushed it off, or if it just went bad, but the rubber between the portion that connects to the crank and the pulley was ripped, and missing in some spots. I replaced the harmonic balancer, and both belts, good to go, everything is running fine.
About a week later, the TCS etc. lights came on, but no check engine. I researched it a bit and came up with three possibilities:
1. Fuse
2. Tone wheel cracked/broken
3. Crankshaft position sensor
I checked the fuses and nothing was burnt, I never lifted the truck up to check the tone wheels.
I've a 2.0L Santa Fe CRDI 4WD, 2003. My Crank position sensor has blown. My question is, does the timing belt have to be replaced with the sensor, or can the sensor be replaced alone? I know the belt must be replaced with petrol models but I've been told it may not be necessary with diesels.
View 1 RepliesGetting code P2125. Read on here to get some electric contact cleaner and see if that works by cleaning the connections.
If I do end up changing out the Throttle Position Sensor, what voltage value do I look for when installing the new one ?
2004 2.4L 4cylinder manual transmission. I had a knock sensor code and replaced it. Then I had a code for the TPS and I replaced it with the new part today and after replacement the vehicle idles at 2000 RPM. what should I change?
View 5 Replies02 Santa Fe 2.4L/ automatic/2 WD. I replaced the fuel filter (only) and have had a nightmare ever since. It takes multiple tries to start, running a little longer each time. When it will finally stay running, only the most delicate of throttle feathering will allow any RPM's to be built up. Any attempt to do otherwise will result is sputtering, bucking and other unhealthy behaviors until the throttle is closed. It also gives off the smell of running rich.
I borrowed a scan tool and got P0136 and P0141, which I expect since the O2 sensor wiring was cut in two by the heat shield shortly after my daughter bout the vehicle. It also is giving me the P0340 Camshaft Position Sensor Circuit code. I had replaced the CMPS and its connector a couple of month ago. I replaced the sensor again to no avail. I have checked the Orange/Black wire from the connector to the ECM and it reads 0 ohms. I get battery voltage at the connector on the Blue supply wire but only get 1.86 to 2.0V when I check the signal with the engine running.
Replacing the crank shaft and camshaft oil seals on a 2001 - 2006 2.4L engine?
I'm in the process of installing a timing belt kit w/water pump, pulleys and all seals. My engine has 190,000 Km with no signs of oil in the timing area, but I figure the oil seal would be worn and or cracked/dried so it would make sense to change them, plus it was included in the kit.
Replacing the tps themselves? Is it something a newbie at diy car stuff can do? I'm getting codes P2016, P1295 and P161B, and I see no problem with the car except one thing, when the engine is cold the shift from P to D is rough. Is the tps causing this?
View 9 Replies