Getting code P2125. Read on here to get some electric contact cleaner and see if that works by cleaning the connections.
If I do end up changing out the Throttle Position Sensor, what voltage value do I look for when installing the new one ?
I have searched and have not found any information on replacing the throttle position sensor. My Santa Fe was running normal. I changed my tp sensor and how it limps along. When I loosened the old TPS, not even removed it, I heard a noise inside the TPS. When I replaced it I adjusted the TPS to read between 9 and 10% on my reader. But when I push on the gas pedal with the key on position the percentage doesn't move. Also when I drive it now it limps along and does not accelerate.
View 2 RepliesReplacing the tps themselves? Is it something a newbie at diy car stuff can do? I'm getting codes P2016, P1295 and P161B, and I see no problem with the car except one thing, when the engine is cold the shift from P to D is rough. Is the tps causing this?
View 9 RepliesAfter heavy rain yesterday my 2005 2.7 Santa fe wouldn't start today. Had it towed to nearby dealer. The crankshaft position sensor needs to be replaced. He claims its melted to the block and oil pan needs to be dropped to remove it.
View 5 Replies2004 2.4L 4cylinder manual transmission. I had a knock sensor code and replaced it. Then I had a code for the TPS and I replaced it with the new part today and after replacement the vehicle idles at 2000 RPM. what should I change?
View 5 RepliesMy check engine light came on the other day and the code stated the the "throttle position is open" so after researching and everyone telling me that i need to change the sensor. I did everything after was fine running better but today only after 3 days replacing it i get the same problems. car has no get up and go hardly can push to 20 mph and when in idle i press the break it starts to bog down and almost want to shut off! and can be really loud...
Santa fe 05' 3.5L ....
02 Santa Fe 2.4L/ automatic/2 WD. I replaced the fuel filter (only) and have had a nightmare ever since. It takes multiple tries to start, running a little longer each time. When it will finally stay running, only the most delicate of throttle feathering will allow any RPM's to be built up. Any attempt to do otherwise will result is sputtering, bucking and other unhealthy behaviors until the throttle is closed. It also gives off the smell of running rich.
I borrowed a scan tool and got P0136 and P0141, which I expect since the O2 sensor wiring was cut in two by the heat shield shortly after my daughter bout the vehicle. It also is giving me the P0340 Camshaft Position Sensor Circuit code. I had replaced the CMPS and its connector a couple of month ago. I replaced the sensor again to no avail. I have checked the Orange/Black wire from the connector to the ECM and it reads 0 ohms. I get battery voltage at the connector on the Blue supply wire but only get 1.86 to 2.0V when I check the signal with the engine running.
Ford catalog does not list the TPS for a 1999 7.3 Super Duty as a separate replaceable part which leads to replacing the whole throttle pedal assembly. I found this to be incorrect. If you have a throttle pedal assembly with separate TPS (separate 3 wire connector) and IVS (Idle Validation Switch 2 wire connector) just the TPS can be replaced.
This is a pic of my 99 with new TPS installed : [URL] .....
Without removing the whole assembly you only need to remove the 2 T25 screws and the connector to replace.
Since this part is listed for more then 20 Ford trucks I figured it would work in my 99 7.3. I bought a brand new TPS from Pete (F250_) that he could not use. He has a 2002 with one 5 wire connector. It works perfectly in my 99. Not sure if it will work in a 2000 or 2001 but if the TPS and IVS each have their own connector it should. Make a visual inspection to be sure.
Part DY-967 or F4SZ-9B989-AA - Potentiometer
I was going to go with a Dorman TPS but like PartsGuyED likes to say "OEM Baby". The OEM TPS through Ed is actually cheaper then the Dorman.
Side-by-side pic of the old and new TPS. Only the center rotating part is different but it fits and works just fine. It also has a better fit so there is less slop and almost immediate response.
NewOldTPS.jpg?t=1269362105
By the way, the original TPS was working fine so I have no idea what the symptoms of a bad TPS are. Since it was available I replaced it to have a spare and to see if this one would work. Both Pete and I thought it would and we were right.
2004 VW R32, No engine mods. I did have the vacuum line sealed off for the flapper mod for about 3 months but is is now back to normal.
I've got the MIL, ESP, and EPC lights on and scanning codes as follows:
Code-P0222
Definition:
- Throttle pedal position (TPP) sensor/switch "B"
- Circuit Low
Explanation:
- Open or short circuit condition
Probable Cause:
- Poor Electrical Connection
- Faulty TPP sensor
- Faulty throttle valve control module
I don't know much about the situation but I took it to my friends shop first where we replaced the Throttle body, intake, and MAF. Didn't fix the problem so I took it to my local VW dealership and the tech's exact words were.."the codes coming up as a throttle pedal sensor. Is there perhaps a sensor by the pedal that I could check?
Am getting an EPC light + limp mode + code for accelerator position sensor (implausible signal). I have swapped out the pedal assembly, so it isn't the sensors themselves, and we've checked the wiring to the pedal assembly... I can feel in-car, and I can see via VAG-COM that one of the two sensors is basically toggling between a sensible % reading of pedal position at one moment, and then zero % the next, and of course every time the sensor reads zero, the ECU notes the error and cuts power... but this only happens when the steering wheel is straight or when turning to the right; I can drive around in a leftward circle all day and night without this occurring.
Why? What is there in the steering (either in the column or at the wheels, or basically any place in between) which, if malfunctioning, could affect the accelerator position sensors in one way or another (i.e. either through the normal operation of a safety system, or through a short or other electrical gremlin)?
my old lady has a 2001 olds intrigue with the 3.5L in it. Sunday evening we replaced the Throttle Position Sensor and the Coolant Temp Sensor. Monday she was on her way back to Iowa and the tempature gauge spiked up to the Hot area. I looked it over and could not find anything wrong. I sent her on her way and she made it about a mile before it did it again. The car will spike up to the hot area but the motor shows no signs of over heating. I checked the temps with a heat gun while the car is idling and read out Thermostat housing-160, Rad-80, Rad hose-130, and coolant 170. I than ran the car up so it shows on the gauge its hot and than checked again, it than reads Thermostat housing-172, Rad-100, Rad hose-134, and coolant 184. If I am running it at 1500 rpms it will spike up but once i take it up to 2500 rpms it drops back down to normal on the gauge. I am lost for what it could be.
View 19 Replies2002 My friend's 2.7L sante fe crankshaft position sensor went bad and I went to replace it. Removed bolt, it was stuck fast, tried to pry out and it broke off leaving the last 1/2 inch stuck in block. Tried drilling a hole in it and using a screw to get it out but no luck. Afraid to keep drilling that I might damage something behind it. How to get it out?
View 9 RepliesWe bought a 2006 Hyundai Sante Fe with the 3.5L and 4 wheel drive about two months ago, it has 94,000 miles on it. It was purchased from a dealership, and they had to work on it for a month before we took it from them because of some lights that were on, resulting in some sensors being replaced. We had it about a month when we took it to the grocery store, when we came back out I started it and it made a terrible noise, but was running, I immediately turned it off. Upon further inspection, the main serpentine belt had snapped, causing some damage to the secondary belt. We towed it home and I began to fix the belts.
When I pulled off the passenger side wheel and access cover, I noticed the remains of the belt were stuck behind the harmonic balancer, I tugged on it with about 5 pounds of force, and the entire pulley fell off of the harmonic balancer. I'm not sure if the belt stacked up behind and pushed it off, or if it just went bad, but the rubber between the portion that connects to the crank and the pulley was ripped, and missing in some spots. I replaced the harmonic balancer, and both belts, good to go, everything is running fine.
About a week later, the TCS etc. lights came on, but no check engine. I researched it a bit and came up with three possibilities:
1. Fuse
2. Tone wheel cracked/broken
3. Crankshaft position sensor
I checked the fuses and nothing was burnt, I never lifted the truck up to check the tone wheels.
I've a 2.0L Santa Fe CRDI 4WD, 2003. My Crank position sensor has blown. My question is, does the timing belt have to be replaced with the sensor, or can the sensor be replaced alone? I know the belt must be replaced with petrol models but I've been told it may not be necessary with diesels.
View 1 RepliesI am having a problem with my 2003 Santa Fe I have taken it to have the check engine light codes read and I have a code for the crankshaft position sensor, random misfires, something with gear 2 and 3 (not sure what it was exactly) it makes a loud noise when in 1st and 2nd gear when I shift out of 2nd the noise gets less and less until its gone and then does not come back until the car sits for a little while and cools down. Its running rough and does not have any power when accelerating. I had the timing belt changed a few weeks ago and it started running funny shortly after. I don't think the guy that did the timing belt knew what he was doing because I had to have someone go behind him and tighten the pulley.
View 3 RepliesI am new to Hyundai. I just picked up a 2003 Elantra and I'm doing a couple fixes to it. When I got it, the engine light was on and the code displayed said it had a bad camshaft position sensor. Is this a common issue with the car and is it an easy fix?
Also, I just installed new brake pads and a new battery. Now the battery and brake lights are on, although I know I didn't break anything. Could installing a new battery cause the two lights to come on?
Codes P0210 and P0733 for throttle sensor and third gear mismatch came in.
Dealer is going to replace throttle position sensor and said the Hangar Bearing is bad needing replacement.
I was just curious how long those jobs take to do roughly?
I need to replace O2 Sensor which is Bank 2 Sensor 2 which needs to be replaced.
Where is this located on a 2009 Hyundai Santa Fe 3.3L
33k Civic 2001 "PO335 Crankshaft Position Sensor A circuit" error code
My Civic 2001 LX (non vtec 1.7) threw an error code today. It was, "PO335 Crankshaft Position Sensor A circuit" error code. It was raining a lot today, and this is the first day that it did it. I have never had this problem before. When the error code came on the engine automatically lost power. I couldn't get the car over 3000 rpm. Then it stalled in an intersection. Now it won't start period. It only has 33k on the clock.
The timing belt was done about two months previous, but i haven't had one problem until today, when it was raining.
My Civic 2001 LX (non vtec 1.7) 33k threw an error code today. It was, "PO335 Crankshaft Position Sensor A circuit" error code. It was raining a lot today, and this is the first day that it did it. I have never had this problem before. When the error code came on the engine automatically lost power. I couldn't get the car over 3000 rpm. Then it stalled in an intersection. Now it won't start period. It only has 33k on the clock.
The timing belt was done about two months previous, but i haven't had one problem until today, when it was raining. So much for a reliable honda.
I was reading the car's settings using the Torque app and an OBDII bluetooth dongle and I realize that at WOT the ECU is only seeing 85% from the TPS. O know on some vehicles there is an actual procedure like turn the key forward, hold the gas pedal at WOT, turn the key all the way forward w/o starting while pulling the turn signal stalk down or something crazy like that to force the ECU to re-measure while you keep the gas pedal pinned to the floor. I know on other cars when it doesn't read a full 100% you miss out on a small amount of power and MPG so if it's an easy procedure with these cars I'd like to reset it. I did some searching but mostly came up with info on how to replace it and a few related subjects but noting on this specifically for this car specifically.
View 2 Replies