Santa FE SM (2001-06) :: Code P0118 - Engine Coolant Temperature Circuit High Input
Sep 1, 2011
Engine light is one for about a month and finally got an ODB II.
Today it reads the error code [b]P0118 which is [b]Engine Coolant Temperature Circuit High Input
The coolant sensor reads 45 C when the key is on "on" position at about 2:30 pm this afternoon and I start the engine about 2 mins the temp jumps to 68 C, are these some logical number?
Does it mean the bad temperature sensor and I need to replace it?
View 5 Replies
Advertisement
I went to my local Autozone today to have a code read and get the freeze frame data. I got a code P0118, Engine Coolant Temperature Circuit High Input. I called the dealer but they are out of stock on the sensor. Would it be a problem to use an after market sensor? I'm just concerned about the quality and accuracy of the sensor.
View 5 Replies
Check engine light is on, this is the code that came up when checked at OReillys, "P0113 Intake Air temperature sensor 1 Circuit high input". Earlier took it to repair shop, he did not give the code, some sensor needs to be changed (don't know if he came up with same code). He had erased the code but it came back on within minutes. Wanted to check if there is any cheaper way to fix this. This is a windstar van.
View 15 Replies
I have a 2003 Santa Fe, V4, 2.4L.
So the other day, my CEL and I got it scanned: p0320, or "Ignition/Distributor Engine Speed Input Circuit Malfunction."
It was accompanied with two symptoms:
1. The car will sometimes sputter on startup, and the tachometer will be zeroed out. I have to turn the car off and turn it back on, and it will start normally, albeit with a bit of a misfire on idle.
2. The car will sometimes die while at a stop. Just like the first symptom, if I turn the car off and turn it back on, it will work normally.
I looked on here, and it seemed like everyone solved a p0320 by replacing the Ignition Failure Sensor. So that's exactly what I did. But nothing changed; I still have the symptoms, and the CEL came back on and is still reading p0320.
What should be my next step? Could it be faulty wires that give power to the Ignition Failure Sensor?
View 3 Replies
My check engine light is on. I got the code pulled at Advance Auto Parts. It is P0107 - MAP Sensor Circuit Low Input. I wanted to test the MAP sensor to see if it is bad. I couldn't find anything online that was Santa Fe or even Hyundai specific as far as testing procedures go. I know you can test the power wire, the ground wire, and the signal wire, from what I could tell from other places I've looked. I got 5ish volts from the power wire and 12ish volts on the ground wire, which is what I understand they should be. I don't have a vacuum pump at the moment, but testing the signal wire with no vacuum I got about 0.02 volts. From what I've read online, it should be around 5 volts, but I wasn't sure if all MAP sensors work the same way. Whether I'm doing this correctly and whether they think the sensor is bad?
View 5 Replies
My cel is once again starring me in the face ... P0018 is the code I got followed by "engine coolant - high input". Where I can buy a book/chart that explains these codes. I'm assuming it is some sort of sensor gone bad but not sure exactly.
View 1 Replies
I have a problem with my sonata NF 2006 the check engine light turn on like 2 days ago and give me the p2128 code say Accelerator pedal Position Circuit - High Input something like that i cheek all the cable off the throttle body to the ecu and i don't see any cable broken how I can check the accelerator pedal sensor? I see in one page a texting the sensor whit a multi miter but was for santa fe and the cable don't have the same colors . I need the accelerator pedal cable diagram and i don't have it ....
View 2 Replies
I'm getting a weird code on my engine it's p1298 which is electric load detector circuit high input and I'm also getting 3 misfire codes but the car runs great what can I do to fix these.
View 10 Replies
Need solving a P0172 code I had. I just pulled out the MAF sensor and cleaned it with a MAF Sensor Cleaner (at most auto parts stores). Worked like a charm and the code went away and the gas smell is gone too.
Now I have a new code - P0712. I have been extensively searching the web and cannot find any good information on how to resolve this issue - "P0712 Transmission Fluid Temperature Sensor Circuit Low Input" ...
I checked the fluid level and it is fine.
I have a 2005 Camry, 2.2 liter, 4 cylinders...
View 4 Replies
I have a 2001 Kia Sephia that quit running as I was driving down the road. The car has a little over 150,000 miles on it and was running fine prior to the incident. The car was responding fine and then suddenly acted as if it lost power and shut down as I was driving. I put a code scanner on the car and retrieved the following codes: 342, 460, and 713, which I understand are the camshaft sensor circuit low input, fuel level circuit malfunction, and transmission temperature circuit high input. Is this a computer that has failed or just all the sensors at once failing? If it is the computer, which one(s)? I was trying to do research and if I saw right, there are more than one ecm's now on cars.
View 13 Replies
I cleaned my k&n air filter on my 02 passat 1.8 turbo let it dry oiled it very lightly, and 50 miles later I get a check engine light on, pulled the code 16486 and it says Mass or Volume Air Flow Circ Low Input. Cleared the code put a frame in until I can get it filter. Why that would throw me that code, k&n oil gumming up my sensor??
View 2 Replies
2011 6.7... My truck is throwing code P2033 Exhaust Gas Temperature Sensor Circuit High Bank 1 Sensor. What is the part number for that sensor?
View 6 Replies
2003 Hyundai Elantra, 1975cc engine, XD. P0198 Error Code.
I know this is the Engine Oil Temperature Sensor High code and I have seen indications this may mean high voltage on this sensor. My problem is I cannot locate this sensor on the engine. From what I have read this sensor is supposed to be on the driver's side of the engine on the head, rear side.
On my engine the head was replaced (unknown to me when I recently purchased the vehicle). From all indications this is not a CVVT engine. The air intake has a MAP sensor that is connected and appears to be functioning properly. The driver's side of the engine does have two coils but I can see no other wires from the wiring harness toward the rear of the head other than leads to the starter.
The cam sensor is located on the passenger side of the engine, rear side. I have found the oil pressure sensor and crankshaft sensor on the front side of the engine block toward the driver's side. I have found and engine temperature sensor on the driver,s side of the engine on a housing connected to a radiator hose.
Oddly enough there was an OCV hanging on the harness toward the front driver's side of the wiring harness. Adjacent to this plug is a second plug on a shorter lead that is not connected to anything. Both of these plugs have two leads but are shaped differently oval for the OCV and the other is rectangular. I am wondering if this rectangular plug is for the engine oil temperature sensor? What I cannot see is where the temperature sensor would screw into the head on the front driver's side (near this plug).
I went to NAPA today and they do not have an engine oil temperature sensor listed, but I was able to find one on line. I cannot find a connection point on the head that looks like the picture of the sensor on-line.
View 3 Replies
So my mom recently bought a 2003 Elantra (75K miles, auto trans) and within a few days the CEL came on. She took it in to PepBoys and had them hook it to their scanner to get the codes out of it. The only code that came up was P0113 Intake Air Temp (IAT) Sensor high input. I've done a little research on the net but there is a lot of random info for this code out there. Is the IAT a separate sensor or is it combined in with the Mass Air Flow (MAF) sensor(if this car even has a MAF) or combined in with the MAP sensor? I've read on the net that it could be any of these 3, I think it's combined into the MAP.
I've also read that this code could be caused by a bad IAT, bad O2 sensor, an exhaust leak, bad wiring/ground(I checked the wiring/grounds visually and everything seems ok) or many other things. If it's as simple as replacing one of the sensors I can do that myself, I just don't want to go randomly buying things and either it be the wrong part or have it be the right part but not fix the problem. The car runs great, even with the CEL on. Yesterday when she stopped by my house I disconnected the battery for a couple minutes and reconnected it, started the car & no CEL. She drove the car for about 125-150 miles before the light came back on.
View 10 Replies
So i got the UM tune done to my car then went and got my TT cams installed. After giving me car the 50 miles to adjust for the cams i get a CEL P0103 Mass or volume air flow circuit high input. Checked the connections around the maf and im noting seeing any broken vac lines or anything out of the ordinary.
Cleaned the maf and cleared the code but the CEL popped back up, got a new maf just because I like spending money on things i dont need and the CEL is still there, low speed or high speed it will pop on.
Is there anything I am missing that could be causing this problem or something i can try other then take to the place that did my cams?
2004 r32
123k miles on it
UM NA tune
carbonio CAI
TT cams
Test pipe and neuspeed cat back exhaust
View 10 Replies
My Santa Fe indicated P0715 for input speed sensor problem. I purchased both sensors and based on forum input I removed the air box and battery to access senors. Output speed sensor is easy to see and access. I am having a problem locating the input sensor. I see wires going to a sensor under both the main wiring harness and shift cable. Is that the location of the input sensor? If so how do you move the wiring harness and shift cable to allow access? If not, where is the input speed sensor located? The Santa Fe is 2001 V6 2.7L.
View 8 Replies
I've owned my 2012 F-250, 6.7L for less than a week and it has a check engine light. The local dealer can't see me for a week, and I need to leave town next week.
I went to AutoZone to have the codes checked and this is what they came back with:
P2033
Exhaust Gas Temperature Sensor Circuit High Bank 1 Sensor 2
P2031
Exhaust Gas Temperature Sensor Circuit High Bank 1 Sensor 2
Can I drive on these codes, or should I park the truck until Ford can see me?
View 2 Replies
I recently got the solid check engine light for my 2003 VW Jetta 1.8T GLS. I used a bluetooth OBDII dongle and Torque Pro to pull the code P0118. This seems to coincide with my symptoms:
Car idle at start in park stays around 1100RPM then in reverse it drops to 1000RPM then back into park and it stays around 900RPM and keeps that at idle.
If I start the car then immediately reverse out of my driveway then the car has a very rough idle but if I wait around 5 seconds in park idle then reverse out of my driveway it is smooth.
My car dash thermometer stays pretty close to the bottom low then after about 4-5 minutes it shoots up to 190F and stays. Gas mileage is also very poor.
I looked up a tutorial which shows the parts needed and how to replace the sensor : [URL] .....
I removed the engine cover and believe I found the coolant temp sensor in the spot the tutorial shows. My question is if there is anything I should be aware of before attempting to replace this sensor that this tutorial doesn't cover? I took a screenshot of what I believe is the coolant temp sensor.
View 8 Replies
CODE P0102 "Mass or Airflow circuit low input" That was the code and upon checking my records prior to storing it for the year. I installed a new IAC,MAF, Fuel Pump and lots of new hoses, PCV, Fuel injection regulator. The Vehicle has only 110K miles. Now here is the clincher, after doing just the fuel pump it ran perfect for at least 25 miles, perfect I say. When I shut if off I got the check engine light, and thus the code which led me to install the other stuff. Now after pondering the matter, seems that it acted in a similar way PRIOR to my doing anything but there was no code previously. Like maybe some strange electrical connection, or something.
View 1 Replies
My 2001 Hyundai Santa Fe V6 is giving out a P0118 code, and the "freeze-frame" data reports a -40F for the coolant temperature. That doesn't make sense so perhaps the sensor is faulty or perhaps the sensor connector is loose?
I'd like to take a look at the coolant temperature sensor but I cannot find it. I have scoured hmaservice, hyunda-forums but all the various pics are still not clear enough for me to actually find the sensor. I have seen all the online pics from Hyundai but I can't get my head around exactly where the sensor is - the pics are either too zoomed in or so many things have been disconnected for the purposes of taking the picture I can't get my bearings.
View 9 Replies
The MIL light came on and I noticed the shifting P-D or P-R was hard. Checked the Transmission Fluid and noticed it was low. Topped it up, but still MIL is on and shifting hard still. I bought a OBD2 Scanner and it returns P0707 "Transmission Range Sensor Circuit Low Input". Should I try clearing the DTC? It's a drag because it's my wife's car and she's driving mine.
View 1 Replies
