Santa FE SM (2001-06) :: Clutch Slipping And Won't Disengage


Oct 15, 2015

Ok santa fe 2006 (facelift) clutch was slipping. We've put new clutch kit in it (thrust bearing; friction and pressure plate). We discovered it had already had the DMF concersion to single mass. So we ordered the single mass clutch kit for it and fitted. All back together, clutch won't disengage and allow you to put it in gear!!! So took it all apart again to check the fitting as the inspection hatch it just didnt appear all fingers on the pressure plate was being pulled.. all looked correct, thrust bearing snapped in to place as it should... we got box back on (making sure the lever entered the thrust bearing correctly) and still no luck. When you press the clutch you can pull the rubber on the slave cylinder back and the piston moves all the way to the circlip. There appears to be movement on the pressure plate in the box. At a complete loss.......... what could have happened?

View 3 Replies

Advertisement

Santa FE SM (2001-06) :: Clutch Replaced But Won't Disengage

Santa Fe 2003 petrol manual 2.4

I had a slipping clutch so decided to change it myself.

I replaced the Dual Mass Flywheel the clutch pressure plate and clutch plate.

Re assembled and the car started first time but the clutch would not disengage.

Pressed the clutch peddle down and it went to the floor until the fluid had filled then it went solid.

I pressed it down again and the clutch did not release so pressed harder and 'pop' the master clynder went - but the clutch would not disengage.

Taken the gearbox back off now and the release bearing is in sit it just would not disengage -

View 4 Replies

Santa FE SM (2001-06) :: Clutch Slipping Above 2500 Rpm

My 2001 santa fe has recently had a new clutch fitted as the old one was slipping but, when towing our caravan at the weekend the clutch is playing up again but, this time the clutch is slipping at anything above 2500 rpm yet she is pulling fine below this rpm.

View 4 Replies

Santa Fe (CM - 2007-12) :: Clutch Does Not Seem To Disengage Until Very Close To The Floor

I picked up my Santa Fe yesterday. 7 seater Premium manual.

However the clutch does not seem to disengage until very close to the floor almost to the extent that I feel the gears crunch and r a little notchy in use because of this ???

Is this a characteristic of the manual gearbox for the new model ???

View 2 Replies

Elantra XD (2001-06) :: Clutch Won't Completely Disengage

We swapped transmissions in 01 elantras.. We installed a new clutch kit . When we go to start the clutch won't completely disengage, it only pulls it some, not enough. We replaced Tran fluid and bled it. We swapped out the throw out bearing arm and at first it worked now it doesn't..

View 3 Replies

Golf IV / Jetta IV :: 2001 Gti VR6 Stuck In Reverse / Clutch Won't Fully Disengage

My 01 GTi (12v VR6) was having some trouble shifting into, and out of, first and reverse so after a bit of research I decided to try adjusting the shift linkage as it seemed like a possible easy fix. After doing that I tried backing it up in the driveway and after a couple of shifts to different gears it ended up getting stuck in reverse. When I pushed in the clutch pedal to let it roll forward I noted that it seemed to be resisting rolling forward despite the steep incline. Once it reached a less steep incline it stopped rolling forward completely, so I'm thinking that it probably won't come out of gear because the clutch won't disengage all the way.

I've done some searching around and from what I've read so far it sounds like it could be a worn or damaged clutch fork, the hydraulic lines, master or slave cylinder, or even a broken clutch plate. What I don't want to do is pull the transmission and clutch, only to find that it was something much easier to fix.

View 19 Replies

Ford Super Duty (1999-2016) :: 2001 F550 - New Clutch Won't Disengage All The Way

I have a 2001 F550 flatbed tow truck with a 7.3 and the ZF 6 trans. i put a Luk clutch flywheel pressure plate new throw out bearing new clutch fork New clutch slave cylinder and master set up. When i push the clutch in it is VERY EASY compared to the way it was before. Ane when you push the clutch in and put it in gear you can hear the clutch disc rubbing on the flywheel and if you lift your foot the thickness of a hair the truck takes off. Also i can't engage my PTO because the clutch is not disengaging all the way. there is No adjustments on this set up. What Now.

View 2 Replies

Santa Fe (CM - 2007-12) :: Clutch Keeps Slipping Out Of Gear

I have a 06 plate Santa Fe 2.2 diesel and i think the cluch is on its way out, keeps slipping out of gear and the pedal itself is not aligned with the other two, mileage is about 79K i think.

View 4 Replies

Golf IV / Jetta IV :: 2001 - Clutch Is Slipping

My 2001 Golf seems like the clutch is slipping. It bangs into gear at low revs so bad you think you've hit a large pothole. I'm hoping it's not the whole transmission that needs replacing, because we only have 135000 on the clock.

View 2 Replies

Santa FE SM (2001-06) :: Transmission Just Stopped Working When Brakes Tapped To Disengage Cruise Control

Same car I posted about a couple of days ago. It was running fine. My son was driving on the freeway, and tapped the brakes to disengage the cruise control, and the transmission just stopped working. It was not in gear after doing this and the transmission would not engage. It was nothing like a slipping transmission. The engine just revs with no resistance.

Got it towed home and checked the codes: P1529, generic 'Check Engine' light from the TCU; P0760 Transmission solenoid C and P0765 Transmission solenoid D. I have googled these codes individually, but not sure how they tie together.

Oh, I overfilled the transmission. Probably a quart too much because I didn't know how much extra I needed for the torque converter. I doubt this is the issue, but I will drain the excess. Where to check next?

View 3 Replies

Eclipse - Mitsubishi :: 2001 - Clutch Slipping Intermittently

The clutch doesn't slip all the time. Sometimes when I put it in third then put the peddle to the floor, it slips for half a second then grabs. Lately noticed it in 4th and 5th gear too. When it does slip, it slips the whole trip. Then later that day it might not slip at all. At first I thought clutch was going, but when does a clutch get better? From what I remember it usually stays the same or gets worse. The fact that there's days it grabs perfect without a slip, leads me to believe something else is causing it. Maybe it's not disengaging or engaging fully.. linkage problem perhaps? I did a quick bleed, hoping it was air. Was better for a couple days after that, then started slipping again.

View 2 Replies

Odyssey :: 2001 - Clutch Slipping - Engine Rev Without Car Moving?

Our 2001, regularly maintained, Odyssey has only 208,000 miles on it, and the transmission has begun to misbehave. Similarly to a clutch's slipping with a manual transmission, sometimes the automatic transmission will "slip," that is the engine will rev without the car's moving. This has been most noticeable, and until recently only noticeable, when the car is first driven on a given day - usually not apparent once the car has "warmed up." My wife and I have independently observed that the problem is more apparent in colder, rainy weather. The problem seems to be getting worse - we've noticed occasional slipping now, for example, when accelerating to pass on a steep uphill.

Question 1: How might the association between the slipping and cold weather/engine temperature be explained?
Question 2: The Odyssey is about due for a new timing belt and water pump. That would seem not worth doing unless the transmission were fixable, in which case, it would seem best to take care of everything at once.

Should we do it, or is it time to retire this car? (We live out in the boonies and have to contend with dusty roads in the summer and drifting snow in the winter; we don't need a fancy car, but do need a reliable one - especially in the winter.

View 5 Replies

Elantra XD (2001-06) :: 1st Gear Keep Slipping - Linkage Adjustment / Hydraulic Clutch

I am searching for any kind of adjustment that might enable me to force the clutch level to the positive stop. It stands off about an 1/8" to 3/16" and I think is the reason I am not getting engagement in first gear, it slips heavily but fine in all other gears. The key way on the the lever prevents me from moving it a notch or two if I thought I could and don't know if that's even the answer . I can't figure out what is preventing it from returning fully on its own I can push it by and and a little fluid will squirt from the reservoir. Ive replaced the slave cylinder and bled it.

Is there any adjustment under the dash? This is a 2001 elantra that I just put a 2000 trans 5 speed.

My original plan was to pull the parts from the 2000 and replace in the 2001. I had lost 1st and 5th totally and found a 2000 that went right in with some minor mtr mnt mods. It shifts just fine except for this 1st gear thing. I saw a video and am having second thought about that move. I dont really want to pull the trans out again.

1st gear just keep slipping. new clutch kit installed when I swapped them out. It feels like a linkage thing somewhat but I cant find adjust ment to tryout.

View 4 Replies

Santa FE SM (2001-06) :: 2004 - Transmission Was Slipping Periodically

2004 2.4L suv with 98K + miles. Transmission was slipping periodically - fluid levels were fine. Someone suggested changing fluids as it may be contaminated. This car has a manual option also that I don't normally use but I did take car out on a longer drive and it shifted as I directed. Since car is almost out of warranty (naturally) I was trying to find answers as I don't feel dealership will be honest with me. While I have not had an actual slip (engine revving and not moving) since fluids changed 2 weeks ago it does seem slow to shift. Since it was not consistent someone said the sensor may be going.

View 4 Replies

Santa FE SM (2001-06) :: 2004 Automatic Transmission Feel Like Slipping Or Trying To Downshift

I have an 04 2.7 litre V6 AWD Santa Fe with 189235 KM , with a Shiftronic transmission, recently, while in "d", the transmission would feel like its slipping or perhaps trying to down shift, its hard to tell what it's doing really, but if you then slapped it over into shiftronic, it would operate fine, no slipping, locks into gear strongly, indicating that its not mechanical, but related to the computer controlling "drive" function of the transmission, I flushed the transmission just after the symptoms arrived (using the correct SP3 fluid) and this made no difference, the old fluid, although ready to be changed, was not burnt or blackend. I thought of getting it reflashed ( read it online) but I am not sure it will work, especially if its like a sensor or something.

View 3 Replies

Santa FE SM (2001-06) :: Tranny Slipping - Power Loss When Going Uphill And Has To Downshift

I just recently bought an 06 Santa Fe with a 2.7l v6. It was a rebuild. It had been hit in the left wheel. The lot put a new fender, suspension parts, axle, etc. It only has 25k actual miles.

We took it on a 100 mile trip today. I noticed if I am going up hill and it has to downshift, it feels like it looses power. The car continues to slow... Like the tranny is slipping. I stopped at Walmart and found the tranny fluid wouldn't even register on the dipstick. I bought Valvoline max life tranny fluid that matches the sp3 specs in the manual. I had to add almost 3 quarts before it was full. I think they may have forgot to add fluid back to replace what leaked out after they replaced the axle It didn't seem to work though when I continued to drive. After I stopped and let it cool about 30 minutes, it did seem a little better.

I guess my question is should I replace the tranny fluid? If so, what should I replace it with? Is there anything else what could be causing this now?

View 1 Replies

Santa FE SM (2001-06) :: 2005 - Slipping / Jerking At About 2500 RPMs In 2nd And 3rd Gear

I have a 2005 Santa Fe that for the last week or so has been slipping/jerking at about 2500rpms (2nd and 3rd gear). This only happens after the car has been warmed up and running for 20 minutes or so. I have put it into manual and it does not do this, only when in auto.

View 2 Replies

Santa FE SM (2001-06) :: 2003 V6 Engine Chugging And Bucking / Belt Slipping Whine

MY 2003 Santa Fe is fwd with the 3.5 v6. While under normal conditions, the engine lost power and began "chugging" and "bucking". There was also a belt slipping "whine" associated with this problem. The problem continued for about two minutes, then corrected itself, and I was able to drive normally.

View 1 Replies

Civic - Honda :: 1995 - Clutch Won't Disengage

I have a 95 Honda civic with a d15b block and a d16z6 head millage unknown I put a new clutch in it already had a new slave and master I installed a few weeks ago and when the car is running with out the clutch pressed in I can run through all the gears shift with ease it's like the clutch is pressed in but it's not

I've tried dropping the tranny and checking the pressure plate the clutch disc throw out bearing pilot bearing all good and installed right I rebleed the system then I removed the slave to see if it was in the hydroelectric system and still no change what am I missing.

View 19 Replies

Ford - Mountaineer :: Cooling Fan Clutch Never Seems To Disengage

The cooling fan clutch never seems to disengage so I was wondering where can i find a clutch that is light duty so it will disengage easy and work with gas mileage napa list two different ones, maybe off a different vehicle....

View 3 Replies

Ford - Explorer :: 1997 - Clutch Won't Disengage

Ok so I have a 97 Ford Explorer 5-speed manual transmission. When I start the truck up in first gear, with my clutch pedal fully depressed, the truck goes forward as if im not pressing the clutch pedal down at all. And if I start the truck up in neutral, with the clutch pedal fully depressed, I cannot get into any gear. There are no leaks anywhere and there is plenty of fluid in the reservoir. What the problem may be or where i might wanna start looking?

View 1 Replies





Copyrights 2005-15 www.bigresource.org, All rights reserved