Santa FE SM (2001-06) :: Check Engine Light Came On - Code For Throttle Position Open
Dec 15, 2011
My check engine light came on the other day and the code stated the the "throttle position is open" so after researching and everyone telling me that i need to change the sensor. I did everything after was fine running better but today only after 3 days replacing it i get the same problems. car has no get up and go hardly can push to 20 mph and when in idle i press the break it starts to bog down and almost want to shut off! and can be really loud...
Santa fe 05' 3.5L ....
View 5 Replies
Advertisement
Getting code P2125. Read on here to get some electric contact cleaner and see if that works by cleaning the connections.
If I do end up changing out the Throttle Position Sensor, what voltage value do I look for when installing the new one ?
View 8 Replies
Check engine light on, car stalled once. Pulling code p0320 "Engine Speed Input Circuit Malfunction." Tachometer works intermittently. Where do I start?
View 2 Replies
Recently got check engine light fault code p0320
2005 3.5 with 172k miles
View 2 Replies
I have a 2005 with 206,000 miles and the check engine light came on. The code reads "pedal position" but local mechanics are not knowledgeable to deal with electronics. The check engine light has been sporadic off and on so is this serious?
View 5 Replies
I have searched and have not found any information on replacing the throttle position sensor. My Santa Fe was running normal. I changed my tp sensor and how it limps along. When I loosened the old TPS, not even removed it, I heard a noise inside the TPS. When I replaced it I adjusted the TPS to read between 9 and 10% on my reader. But when I push on the gas pedal with the key on position the percentage doesn't move. Also when I drive it now it limps along and does not accelerate.
View 2 Replies
1996 Ford Explorer on a small island with no mechanics. Vehicle does less than 100 miles per year, never over 20 mph. The check engine light came on and the code reader says it's a problem with the Camshaft Position Sensor. The vehicle runs fine, just as it did before the check engine light came on. I'm tempted to put some electrical tape over the check engine light and keep driving.
View 2 Replies
2004 2.4L 4cylinder manual transmission. I had a knock sensor code and replaced it. Then I had a code for the TPS and I replaced it with the new part today and after replacement the vehicle idles at 2000 RPM. what should I change?
View 5 Replies
I brought my Prius, 128,000 miles, into the dealer with the check engine light on. Runs fine, and checked the gas cap. Toyota dealer said they need to replace 4 fuel injectors, replace oxygen sensor, and clean the throttle body. Check engine light needs to be off so I can pass emission test.
View 8 Replies
At roughly 140,000 miles, my wife's '07 Santa Fe GLS has thrown a P0456 code. Does this code on a Santa Fe common?
It is "evaporative emission system leak detected (very small leak)." The good news, I guess, is that it is 'very small.' However, being small may make it more difficult to detect.
View 3 Replies
I've recently bought used Hyundai SantaFe 2007 and the engine check light lit up. I've bought EML327 OBD2 scanner, it showed P1405 meaning "EGR tempereature sensor incorrect". Some of my friends says it has something to do with CPF filter and EGR valve. They think, i should clean both CPF and EGR. Car service told me that DPF (not CPF) filter cleaning costs arround 350eu and one service told me to simply take it out and reprogram car computer. As far as EGR valve cleaning goes, no service wants to do this. I don't really know much about cars, so my main question is what would be my next step in trying to fix this error.
View 3 Replies
My 2010 Santa Fe is only 2 month old and has 2000km now the check engine light is on. Went to the dealer and found out the code is P200A -Intake manifold runner performance. And they just clear the code. What does this code mean?
View 22 Replies
Have 2 problems that are giving me major problems.....especially with 100 degree heat in Dallas.
1. Ac stopped blowing cold last night out of blue. Still blows just not cold. Replaced bad fuse and drove for 5 minutes. Blew again. Checked out the control/ circuit board but looks ok. Really cant afford dealer.
2. Check engine light problem for months. Gas gauge wasn't working. Replaced fuel sending units and it fixed that but still light. Code says p441. Dealer said need solenoid valve. Replaced both the solenoid valve and the purge control valve. Still check engine light.
View 2 Replies
I own the 2014 Santa fe turbo 2.0 litre limited which has 4000 km on it. Within 210 km the engine light came on 3 times. I took it into the shop and they ran a code of P0303 which is a misfire, they changed the coils #2 and #3 and cleared the code. The second time it showed the same code but the shop said it was in the history so that is why the same code came up again. They ran an update ECM? and all was good. Now the 3rd time they tell me no code has come up and can't do anything about the engine (they cleared it) but it was like chasing ghosts. My vehicle runs great so not sure why I am constantly having this issue.
View 68 Replies
My '04 santa fe 3.5 v6 gls/lx, 79k miles, gas, auto, check light has just come on while I was driving a less than 10 mile journey. How can I check what is wrong. Do I need some sort of diagnostic code checker. Do any national outlets check it for free (Pep Boys or Auto Zone, etc).
Just 5 days ago (about 50 miles only) I had timing belt, water pump, plugs and leads replaced, brakes checked and lubes flushed; BUT not at above dealers. I would rather know what the code is saying before I go back to the shop who carried out the work.
View 12 Replies
How can i turn off check engine light (hyundai santa fe 2003 3.5) by fuse ? I do not have any code scanner.
View 10 Replies
I recently purchased a 3.5 V6 Santa fe. The Check engine light keeps going on. I took it to a few shops and I am getting the same code. It is the O2 sensor in bank one. (I think the the code was po170.) The light keeps going on and off. All I can find are the same problems with different Santa Fe engines (2.7, etc. )... My SUV has 100,050 miles on it.
View 1 Replies
My 2001 Buick Lasebre is not starting properly. I have to pump the gas several times before it will start; then when it is started at low speeds or idle it wants to stall. As long as I can some how keep pushing the gas peddle it wont stall. On the other hand when I am driving at higher speeds, anything above 40 or so it runs perfect. The check engine light was on and shows EGR valve stuck open. I have replaced the Mass airflow sensor, fuel filter, and the EGR valve. I had the code cleared and a short while later my check engine light came back on with the exact same reading. I bought this car only a week ago and was not expecting to have to fix a car I just bought and ran fine while test driving it. I have read may different forum that say that it could be anything from my fuel pump to vacuum hoses, to some other sensor.
View 19 Replies
I have had a check engine light go on and off with P0700 and P0741 but since the flush day 3 it hasnt come back on and it was chucking with rpm doing small jumps... but now it does it in the mornings after sitting all night after a few chucks its fine for the rest of the day til the next day no check engine light so far, but transmission flush has worked a lot not as bad as before the flush.. So what else could be causing it? Its a 2006 hyundai santa fe with 274,000 kms.
View 24 Replies
I have A 2001 Santa Fe. The check engine light came on about 3 weeks ago and the car was still running fine up until the last few days it felt a little sluggish. Today I got a little muffled backfire noise. It was like a putting noise if I pushed on the gas to hard to speed up. The car has 95,000 miles on it.The car starts up with no problems and doesn't stall. Its A 6 cylinder All wheel drive vehicle.
View 10 Replies
I have a 2002 SF GLS/LX (?) with 2.7 L V6 2WD (60,000 miles) and it started to apply the ABS brakes in a random manner. Found out it was caused by a broken front wheel tone ring. So, I pulled the ABS fuse under the dash and it stopped the brake problem. Drove it today to pick up some wood and now the check engine light has come on.
My neighbor has an OBD scanner and he plugged it in and said I have a P0501 code and a P1529 code, but he didn't know what they meant. What they mean and are they related to me pulling the fuse under the dash? Did I pull the wrong fuse? Is there another fuse somewhere that I should have pulled?
View 1 Replies
