Santa FE SM (2001-06) :: Car Starts Up And Idles At Around 2,000 Rpms
Dec 20, 2012
This all started out when I wanted to change my original plugs that had 200k miles on them. I have that part done now and new wires. Then it wouldn't start without me starting it while holding the gas pedal down. Then I would have to press the pedal down or it would die.
I may need to clean the throttle body. I bought some Valvoline Throttle Body Cleaner and cleaned the throttle body it was black inside and now it's nice and clean. After that the car starts up fine except on the first try. It starts up and idles at around 2,000 rpms. When I press the brake it drops to 1,000, then back up to 2,000. The strangest part is I have no acceleration power now. I can press the pedal to the floor and it will only go to 3,000 rpms. It will slowly get faster as I drive but there's no immediate response when I press the pedal down.
Why would cleaning the throttle body do this? It throws a code when I first start it and it dies the P1110 code but I think that is because the rpms are at 600 when it catches it. No misfire codes or anything, so I think the plugs and wires are working. Just the faster than normal idle now and no power when I press the pedal down.
Would the throttle body cleaner hurt the throttle position sensor?
View 7 Replies
Advertisement
If I don't keep in the throttle immediately after start up it will stall a lot of the time. It doesn't do this every time or if it sits for a while but if I drive it and then stop off at a store or something and then go to start it back up it gives me this problem. I notice it idles about 3-4k RPM's when I stop at a light or something too.
View 14 Replies
2007 5.4 . Starts good , idles all day. As soon as you try to rev it, it stumbles rattles etc. Shut it off, wait a second, restart then Idles fine. I watched live Data and it carries on when the VVT solenoids become active (above 800 rpm).There duty cycle goes to 60-70 percent while revving. I think it Is just one side of the engine. Could be VVT solenoids sticking on? yes ? No?
View 3 Replies
I have a 05 Hyundai Elantra 2.0L engine(Manual) thats been acting funny. There's a couple issues im having with it.
1. Not matter how far the gas pedal pushed down RPMs wont go over 2,500
2. Car surges and jumps back and fourth sometimes.
3. Idles around 900rpm
4. Sometimes when I take off I'm able to get around 40 mph, and thats where it tops out at.
5. Shifting into 1st gear feels a little spongy
6. Also it can go all the way into 4th gear without dying and the top speed will only be at 10mph
Things I've done so far.
1. Compression test cylinders all came back fine
2. Replaced TPS
3. Checked to make sure exhaust wasn't obstructed
4. I got a stethoscope and listened for the ticking for the fuel injectors and also got some fuel injector cleaner.
View 18 Replies
Elantra has set for a couple months. Wife totaled her other car so is gonna start driving this again. Well any ways wen the car sets and idles it starts to overheat. When driving it never gets hot. New thermostat and fluids...
View 5 Replies
I replaced a dead battery in my '05 3.5 v6 Santa Fe. Other than the dead battery the car was running fine. After replacing battery, at idle, the RPMs drop below 500 and then go back up to over 1000 and then drops back down to 500-600. It has almost stalled a few times. At the low RPMs it diesels a little. When the RPMs spike the car surges and if I wasn't heavy on the brake, I'm sure I would have rear-ended the car in front of me. No check engine, no codes. Is this normal? I replaced the battery about 4 years ago and don't recall this behavior. If not normal, what is going on and where do I look? Its my wife's car and don't feel safe letting her drive it until this gets resolved.
View 16 Replies
I have an 02 Santa Fe with the 2.7, 4x4. This started a few weeks ago. When it is first started, it cranks over for a few then starts, idles 1500-2000 rpm. It is a little hesitant at first, but will eventually run fine. If I go to the store after it is warmed up, shut it off, then go back to start it again after shopping, it does the cranking over for a few, and when it starts, you can smell gas (strong smell). when you go to take off, it hesitates real bad, backfire rumble through the exhaust, has no power, bucks, and you have to feather the throttle to keep it running. If you put your foot to the floor, it does nothing, 20 mph if your lucky. if you can keep it running long enough without it stalling, which it has done, and hit the highway, and get going, it will eventually work itself out and run ok again. There is NO CEL. It is getting worse.
View 1 Replies
I have a 2004 Santa Fe 3.5L 4WD. It's been running rough on occasion for quite a while now, but it's only been an occasional thing. I replaced the front passenger side axle and went for a test drive and the vehicle was barely running. I put the throttle to the floor and it does nothing more than idle. I barely made it home and am afraid to pull it out of the drive. I started it up this morning and it seemed to be idling just fine. I pushed the brake to put it in gear and it started stumbling. When I put it in gear, same thing, pedal not doing hardly anything.
The check engine light did come on and I had a buddy bring down a scanner to check it. I don't know if these are Hyundai specific codes or not, but here's what he pulled: P1110, P2127, P1173, and P1192. I'm thinking throttle position sensor, but am unsure. I've put a lot of time and money into this vehicle lately. I've spent some money and a lot of time trying to figure out why it was showing abs and traction control lights. Turned out to be the exciter ring on the axle was broke.
View 1 Replies
We have a 2006 Santa Fe Hyunda with 100,000 miles that when we hit 80 mph on the highway the rpms drop to zero and stay there. We just had the camshaft and crankshaft replaced. Why this is happening?"
View 3 Replies
I had a strange problem tonight, my car wouldn't start in park as it normally does, but did start in neutral? I certainly don't want it NOT to start! is there some sort of sensor that tells the car its in park and therefore allows it to start, which may have slipped/become faulty telling the car its safe to start, even though its in neutral and not park?
View 4 Replies
The other day I was driving my Santa Fe. I noticed the RPMs went up and then the car started slowing down, so I pulled over. Since then the car won't drive. Engine starts up but the car won't move at all. When I push the gas pedal I hear the engine revving, but no movement in drive or reverse. No check engine light, and I checked the transmission fluid, looks and smells good. I checked and it has no transmission pressure. I verified by removing the transmission cooler lines and shifted the truck in all gears. Nada. Could it be the filter, a sensor or the torque converter? Or am I looking at having to replace the whole transmission?
View 21 Replies
We just replaced the starter on a 2004 Hyundai Santa fe 3.5. The car now starts, but won't idle. I can keep my foot on the gas and keep it running, but as soon as I let my foot off the gas it dies. We didn't have this problem before replacing the starter. Where to start looking?
View 3 Replies
My car has the same issue, its a 2001 santa 2.4 . Its starts and then shut off after 3 seconds. camshaft was replaced twice already. still same issue, die after 3 seconds. everything seems to be fine.
What about fuel pressure at the rails? If the pump runs for a moment when the key is turned to the on position then when cranking it stops. That would let the engine start and run for about three seconds. Could it be the ignition switch?
View 9 Replies
Earlier this week, noticed that my car was surging on its own; basically, if I came to a stop, I could still feel the engine, like it wanted to just take off. And if I would have taken my foot off the pedal, it would have done just that. Also, I knew the car had gas, but sometimes, when starting the car it would not start at all. I would have to wait about 5 minutes or so and add major gas to it with the pedal and then finally it would engage. And then the last thing was that when I would get to my destination and put it in Park, the RPMs would go up to about 1500 or so, maybe a bit higher and then stay there and go back down to about 1000, without me pressing on the gas pedal at all. So anyway, thought it was the throttle position sensor, so I had my Dad install a new one on the car. It was a pretty easy process and thought that took care of the problem.
The surging part basically stopped, so the new TPS took care of that, but then it still had problems with starting. Took it to a car repair place the next day and they changed out the spark plugs, said that they were causing a misfire in the engine. Also changed ignition wires and a new gasket. So after they were done, drove away and all seemed to be fine, but then went to the dentist and Parked and then the RPMs went up again. Tried to start it immediately afterwards and it wouldn't start again. Tried a few minutes later, added gas with the pedal and it did start. Took it back to the car repair place, they drove it around, inspected everything and everything checked out fine. (Yeah, of course!) Ok, so just thought maybe the repairs were taking a bit to take effect. But later in the day, wouldn't start again.
So next morning, took it to the Hyundai dealer. They looked at everything for about 2 hrs, and said that there was a vacuum hose that was leaking, so they put on a new clamp but everything else checked out okay. Ok, so now it starts fine every time, but today it did that high RPM thing again when I put it into Park. It doesn't do it every time, but the RPM will just go up randomly then go back down and go back to normal. Should I clean the IAC with some type of carb cleaner to get out any carbon deposits? Or could it be a bad MAF sensor? Not sure what the symptoms are of that. Everything else seems to be okay now except for the random high RPMs when in Park and sometimes at startup too.
It's a 2 WD, V6 engine.
View 3 Replies
I have a 2001 Hyundai Santa Fe LX with 214,000 miles on it. In general, I am having two problems which are most likely related. I would like to get opinions on what is causing the problems, how to fix the problems, and what the cost might be for the fix. This is an older car and I don't want to bring it to a mechanic to just do searching.
1. RPMs fluctuate quickly at slower speeds in town stop and go traffic and while parking in Drive or Reverse. Fluctuation can be between 1000 to 2000 and 3000 RPMs back and forth.
2. Car stalls while sitting at stops when in Drive. When car stalls, RPMs have suddenly decreased to 0 (zero).
3. RPMs fluctuating and car stalling typically occur after I have made my first stop and have turned off the car.
There is also a Check Engine Light Code: P0304, Cylinder 4 Misfire Detected. I changed the vehicle speed sensor a few months ago.
Here are the details of what has been happening, when it happens, and what I have tried.
- When RPMs fluctuate, the car slowly accelerates and slows down and I can hear revving high and low. This happens when the RPMS fluctuate just a few RPMs around 1000 and when the RPMs are fluctuating up to higher RPMs.
- After the car has been driven for about 45 minutes and car is at slower speeds, RPMs will fall to zero while at stop and in Drive, and the RPM fluctuation will begin.
- RPMs jump to 2000 or 3000 and stay there but do not fluctuate when car is put in Park and Neutral.
- When car is in Park and at 2000 or 3000 RPMs, car takes a few extra seconds to turn off.
- Car accelerates without pressing gas pedal and will accelerate up to 40 mph.
- Car will sometimes lurch at slower speeds of 15, 25, and 35 mph when RPMs are fluctuating or when the gas pedal is pressed.
- When RPMs are fluctuating and at 1000 or higher and I am pressing the brake to slow down, the car fights in Drive and in Reverse.
- RPM fluctuation does not occur at interstate speeds.
- A couple days ago, when I was at interstate speeds of 60 to 75 mph and pressed the gas pedal, the car would stutter and jerk.
- RPM fluctuation and stalling primarily do not occur when the car is started at the beginning of the day or when the car has been off for several hours.
- Twice In the last week the RPM fluctuation and stalling occurred even after car was not started for several hours and after only about 5 to 10 minutes of driving in town stop and go traffic.
- Sometimes car stalls when I'm at a stop and slightly press the gas pedal to start driving.
- There are times in town traffic when the car is operating normally and is at 750 RPMs at stop, then the RPMs suddenly decreased from 750 to 0 (zero) and the car stalls.
- From Neutral, sometimes when I simultaneously put the car in Drive and press the gas pedal either by feathering or forcefully pressing pedal 3/4 to the floor, the car would have a delayed reaction to accelerate but would not shut off.
- After car has stalled, if I try to start it right away, the car cranks but does not start for about 5 minutes.
- The time between stalling and being able to get the car to turn back on has increased over time from starting up at first crank to not starting for 5 minutes.
- If I let the car sit for 3 to 5 minutes after it has stalled, the car starts up but takes a couple seconds to start while pumping the gas pedal.
- Issues have been happening since November but are getting more frequent.
- Stalling is happening more frequently and within minutes of each other.
View 10 Replies
Codes currently on ecm: P0134, P2125, P1174, P0735 My 2003 Santa Fe 2wd 3.5l with 160,000 miles was driving fine, then all the sudden whenever I reach about 3500 rpms there's a grinding noise that sounds like its coming from near or in the automatic transmission. As for the codes: P0134- I just replaced the o2 sensor with an oem part from autozone, so not sure why that's popping up. The connections look fine. P2125 and P1174- I'm trying to figure out whether the accelerator position sensor or throttle position sensor needs to be replaced. I have a multimeter but don't know if that will be able to tell me which one is out. The P0735 gear 5 incorrect ratio and grinding noise at 3500 rpms is what I am mostly worried about though. Could a transmission flush work with that?
View 2 Replies
2004 Santa fe. Having issues with RPM running high. When car is started, RPM sits at 1500 for a few mins, then drops to 500. Seems to be having issues either getting into gear or staying. At any mph, car seems to surge and not feel like it's getting either gas or power. While on cruise at 55+ mph, car will also surge with RPM dropping 500, then kicking back in. This goes on every few seconds up to random times.
Had it looked at this past weekend at a dealer, and of course it didn't do it one time, after doing it for a half hour prior on the interstate. Tech found no error codes when he checked it as well. Car was fine for an additional 300 miles, then it started again out of the blue. Pulled out at a red light and I though I was going to stall.
Just got laid off so I'm trying to eliminate before putting a lot of money into it if I don't have to. 132,000 miles.
View 2 Replies
My beloved Hyundai Santa Fe,2006 model's engine light came up. The engine starts and than about 10 seconds after cuts out straight away. What to do. I have always taken care of this car and being serviced well.
View 23 Replies
I have an issue of fuel pressure I believe on my 2003 3.5 Santa fe...It would start then stall...I'm at my wits end with this thing...I checked the relay and its good...checked all fuses and they are good...I don't hear the 2-3 second whine of the pump when I turn the ignition to the on position, so I suspected a bad pump...but before I bought a new pump I took out the back seat, removed the access cover and checked the connector to see if the pump is getting power...its not...I'm at a loss as to where to look next...
View 35 Replies
My 3003 Santa Fe AWD has an issue with the blower fan. It stops, then starts working and clicking can be heard behind the dash when this happens. The clicking seems to increase when the climatization switch (the one that switches the air to the front vents, foot wells, windshield, etc) is turned off. When it clicks while the switch is on the off position, the blower blows for a split second every time the click is audible. It kind of turns itself on/off. Before I start replacing parts, I suspect the fan relay to be the culprit, but I'm not sure.
View 2 Replies
My Santa Fe driving me crazy. Have a 2002 Santa Fe 4 cyl with a problem. It will start when cold and run normal about 2 minutes. Then it starts running erratically like a misfire. If you let it idle this way it will stall quickly and not restart until totally cold again the next day. If you catch it quick enough and continually pump the throttle it continues to run rough until it starts to warm up. As it warms up the engine slowly improves until it reaches operating temp. At this point the misfire is much less but still there. If you shut it off for more than 10 minutes it will not start until the next day. There are no codes at this time. I have changed the coolant temp. sensor, the cam position sensor, fuel pump and screen, spark plugs and wires. I have also verified all timing marks on the crank, cams, etc. The crank sensor was replaced about 40k ago when the timing belt was replaced. What can I look for now???
View 2 Replies
