When I brake slow to stop or go slow round corner brake pedal judders with a brake judder noise I have read it could be cv axle or the ring tone or sensor cable.
I have replaced front discs and pads because I thought it was that but not then abs light came on and went back off and and one time stayed for awhile.
Santa Fe 05 Diesel 48000 on clock
2001 Toyota Sequoia LTD, 115,000 miles, replaced cal & discs & steering rack bushings early last year. Lately after 20 to 30 minutes of hwy at 70mph touching the brakes to shave off 10 to 15mph causes heavy vibrations from the front brakes like the wheels aren't round. No lights, ABS or VSC, no noise from the ABS unit. Same in 2WD, 4WD, VSC on or off. Touch the brakes from 70mph and it feels like slowing/stopping on washboard??? Tech checked, no codes present . Brakes function fine around town as does the ABS & VSC, alignment good.
View 1 Replies I have a 2005 Santa Fe 2.7 V6.
For over a month I have had a soft brake pedal. For those that may not know what that is, I push my brake pedal down 3/4 of the way, and I'll finally feel the brakes catch; however, I cannot stop quickly. I have had to use the Sports Mode to slow down my car many times.
I brought it to my local mechanic and he has done the following:
1) he thought it might have been the master cylinder, so he replaced it. he checked the old master cylinder and found nothing wrong.
2) bled the brake system a couple of times, but it still came back
3) brought my car to the local dealer to drain the ABS system. The problem still came back.
I waited over an hour as the dealership's service department checked out the car. Someone finally came to me and said they checked the lines and they are not leaking, so it has to be the master cylinder. I told the guy that it's a brand new cylinder, and when the mechanic looked at the old one, he said there was nothing wrong with it. All he could say was it's not the lines, it's the cylinder. If I had the problem before & after the master cylinder was replaced, & nothing was wrong with the original master cylinder, how is it the master cylinder?
I called my local mechanic on my way home from the dealership and told him what happened. He said he was going to do some research, mentioned something about replacing something with the ABS and he would call me today.
I searched the forums for brake issues and saw something about cracked ABS rings. Could that be an issue? Could it be something else?
Soft Pedal. 2004 Santa Fe, front wheel drive 4cyl, 2.4l
When I first owned this Santa Fe the brake pedal was high and had lots of stopping power, over the last few years I noticed the pedal was getting lower. I have replaced everything needed thus far including pads, rotors and everything has recently been serviced front/rear/emergency brake/ calipers and still a soft pedal. Had the guys in our recon shop replace master cylinder and bleed the lines a few times with a full week in between bleeding to ensure there was no air in the lines. The mechanics are stumped but I'm wondering if we missed something...... I still can stop no problem but there is no grab in brakes until pedal is half way down to the floor or worse.
I have a santa fe 2002 diesel the abs lights stop on all the time the brake pedal has a bad judder on it when braking. I have taken the fuses out and it will still judder. The only thing that is when i disconnect each sensor the red brake light stops on but not with the osf front sensor. All the rings look ok but when i had a problem with 1 of them the abs light would go out then return on...
View 1 RepliesHere's the short of it. 3rd time in a year the brakes on my 2005 SF (177K miles, 2.7L) have gone out.
The brake pedal is very soft and goes to the floor before braking occurs. Typical signs of a bad master cylinder.
The first time was a year ago. I bought a re-manufactured master cylinder, change it and bled the brakes. Worked like a champ and lasted 10 months.
To months ago same exact symptoms. I assume it was a bad re-man part. It's under warranty, not big deal. I do warranty exchange, bleed system, brakes return. All is good.
Less then 3 weeks later, brakes gone, same symptoms! This time I spend the difference and get a brand new OEM cylinder with reservoir. Replace, bleed, problem fixed. Brakes go out in less than a week.
I'm not leaking anywhere. Reservoir is to corect level. ABS light is NOT on. No chattering in brakes. Braking is smooth both when power brakes work and when not. No visible damage to calipers. I'm 99% sure there is no air in the system, but I'm going to try bleeding again. I have not put it up on a lift to yet to check all the lines.
I've been noticing an odd noise in the brake pedal in our '03 Santa Fe. I don't hear it all the time (almost never on the highway), but especially hear it in stop-and-go traffic. It's sort of a whirr, a "RRrrr". I've googled and watched YT videos and it's definitely not a hissing sound or a grinding sound, nor do I notice any difference in the brakes' responsiveness.
I'm apprehensive of taking it to the dealer for service because I only plan to have this vehicle for at most three more weeks. Have only held onto it this long because we couldn't afford to replace it until we sold our house-- which we've just done, and are about to move to a city about an hour away on 7/5. We'll trade in the car within a couple of weeks of moving.
The noise is definitely from the pedal and isn't anything like squeaking brake pads (I currently live in the DC metro area, so squeaky brakes become very familiar with all the stop-start traffic!). The videos I've found that point to a booster problem have a decided hiss, and it's not that either. Don't want to be unsafe in the time we've got left, but also don't want to throw another thousand bucks (every time something breaks in that darn thing, it always seems like it's about $800) into a car we won't have in a month's time.
I have a 2004 Santa Fe 3.5L 4WD. It's been running rough on occasion for quite a while now, but it's only been an occasional thing. I replaced the front passenger side axle and went for a test drive and the vehicle was barely running. I put the throttle to the floor and it does nothing more than idle. I barely made it home and am afraid to pull it out of the drive. I started it up this morning and it seemed to be idling just fine. I pushed the brake to put it in gear and it started stumbling. When I put it in gear, same thing, pedal not doing hardly anything.
The check engine light did come on and I had a buddy bring down a scanner to check it. I don't know if these are Hyundai specific codes or not, but here's what he pulled: P1110, P2127, P1173, and P1192. I'm thinking throttle position sensor, but am unsure. I've put a lot of time and money into this vehicle lately. I've spent some money and a lot of time trying to figure out why it was showing abs and traction control lights. Turned out to be the exciter ring on the axle was broke.
Just hit 225k with my 2004 Prius about a week ago. I passed inspection without replacing the (slightly) cracked rubber bushings for now, but what worries me is the cracks and a slight hole (it has not rusted completely through). Pictures attached. Should I do anything about this, and if so what?
Also, I've noticed that when I let go of the brake pedal, especially after a medium to the hard stop, I hear a squeaking... what's the cause for that? I know the front rotors have a bit of rust on the edges, but not sure if that's the cause... it seems to come from the back.
Other than that, the only other noise I've noticed is a slight clacking/tapping when the A/C is on, usually in hotter weather. The only thing I needed to pass inspection was to replace the muffler after a year and 1/2 ago, the last non-OEM part they put in at another shop was junk and rusted through pretty badly leaving a hole that was leaking. Ended up getting it replaced at the dealer with the OEM part this time...
My Sienna 2005 experience intermittent complete brake failure 3 times within 18,000 miles,the brake pedal goes to the floor and it does not slow down, so I coast until I stop. However, when I release the brake pedal and then reapply the brakes, it works fine. A non-Toyota mechanic thinks it's due to malfunction of ABS. The dealership is unable to finds error codes and brakes work fine when the Sienna is in their hands. I scared that the brakes will not work the next time I reapply the brakes.
View 30 RepliesM friend with his 98 gmc. When stopping the breaks are normal until getting slow then the abs motor comes on and the break pedal sinks to the floor. The truck stops but the abs motor runs constant until you release the pedal. This is happening on dry roads. What is there to check before condemning the abs module?
View 4 RepliesYour breaks yet? Mine are starting to get really annoying, that high pitch noise at slow speeds with just a slight touch on the break peddle. To give an idea of loud, I have hearing loss from my job in the military and they are starting to bother me.
View 13 Replies2004 XG350 with the Sigma engine, 133,xxx miles.
In the picture I attached, the large silver bolt is leaking. Its a slow leak: yesterday morning I wiped it off, and then we I got home from work there was a bead of power steering fluid, but not enough to drip.
What is the best way to fix this? Is it as simple as tightening it?
Vehicle:
01 Santa Fe LX 2.7 AWD w/112k miles
Symptoms:
- Slow Start (when cranking takes 2 full seconds before it will turn over and you can hear the engine cranking slower, use to turn over right away)
- Very Strong Burning Rubber Smell
History:
Last January it got down to -20 here in Albuquerque and I would have to go to work at that time. About a week later (when it was still getting down to about 0) I was driving home from work when I smelled a slight smell of burning rubber. I thought it was the car in front of me. The next day I had the same thing. It continued for about a month till the temps rose a bit and then went away. I could never find the cause. I then went all spring, summer, and fall without any problems on my Santa Fe.
As the temps begun to drop over the past 6 weeks we started to smell the burning rubber again, at first only when I would start the car till it warmed up. About 2 weeks ago the car started cranking slower and would take longer to turn over and within the past week I can smell the burning rubber smell even when I had the engine at temp. There's not any idiot lights on. The car is running fine except for what was mentioned, gets up to temp and stays there (a little below the middle on the gauge like normal). I pop the hood and looked at the belt, looked good (no cracks). Checked all the fluids and the only thing that's low is the coolant.
I have two Hyundais - 2011 Sonata SE and a 2008 Santa Fe Limited. here is my problem with the Santa Fe.
Brakes: Changed front rotors and pads - rear had the rotors resurfaced and installed new pads. Still get a lot of pulsation when stepping on brake pedal. Is there anything else I should be checking?
I went to adjust my Santa Fe's parking brake (pedal version) and am trying to troubleshoot. The pedal goes all the way to the floor, something like 11+ clicks....
I jacked up the rear end, pulled the tires off, rotated the drum so that I could access the adjusting nut and used a flat head screwdriver to rotate it all the way back to where it wouldn't rotate anymore. After that I clicked it ~5-7 clicks. Same process on each side.
Went to go test the pedal, still goes to the floor, same number of clicks, etc.
Tried to locate an adjusting nut for the pedal but cannot find one, if one exists. The fuse box sits perfectly in the way but I was able to view everything with a little bit of effort and still couldn't locate the mythical adjusting nut.
I know I did the adjustment on the rear brakes correctly so it's an issue with the pedal/cable/nut.
2001 Santa Fe 2.7L 4wd ... In December I bought this vehicle it only has 95K on it. When I drove the car home I noticed it needed brakes so I put brand new pads and rotors on the whole way around. I changed the oil, air filter, wiper blades, and made sure all fluids were good. I had the front spring recall done and also put some new sway bar end links on the front. The car runs fine and I am rather impressed with it. It does have some rust but I'm not to worried about that. This isn't my everyday car just a winter/extra car. Recently I have been getting some clunking only when going from reverse to drive and going slow. You get a clunk..clunk pause clunk..clunk almost like you have a flat but once I get the car up to speed it is fine and you never hear it again until the car sits a day or so and then it will do it again. I don't know if I have a differential problem or a u joint or maybe something with the e brake or rear brakes? but it is -3 right now outside and I would rather know where to start so that when I can take a look at it I know some things to check or what it might be.
View 3 RepliesI have a 2010 Santa Fe w/ ~25,000km. Yesterday, I noticed that after depressing the brake pedal (while driving) i hear a wheezing noise and then a click right before i come to a complete stop. When i am stationary, and i depress the break pedal, i hear the clicking noise but no wheezing sound.
I just took it into service today and even drove around the lot with one of the service techs and he says its normal. That the clicking noise is coming from the shifter release. I don't believe i heard this sound when i bought it, nor any other time till yesterday. The sound is driving me crazy! This cant be normal .... can it?
I have a Hyundai Santa fe 2004 6cyl 2.7 L , AWD. I am having problem of slow acceleration which is worse after a stop sign or red light. Sometimes while taking turns I feels like that I will not move and I was lucky to be not hit by a Car coming from opposite direction while taking a left turn today.
The Truck’s exhaust pipe broke recently and a auto garage welded it. But I am facing the above problem immediately after the repair of exhaust pipe. If I put more pressure on gas pedal then a mal function indicator comes and today I took it to another mechanic and he gets the error code of P0303 –engine misfire and wants to charge me ~ $600 $ to replace spark plugs and wires. The malfunction indicator goes off also while I am driving and can comes back after a while or a day. With the indicator on, the car drives erratic (minor jolts ) for few meters and then its fine. Since when I am driving on highways then I can go higher speeds without any problem. Is it still misfire issue???
Here's the run down:
-bought 6 months ago for cheap because it wouldn't pass smog test
-changed Purge Control Valve (PCV) and it passed
-filled with gas, heard popping noises like a backfire, and coded it read the same "Bank 1 and Bank 2 running lean, like it did before the PCV and then also "Cylinder 3 Misfire" appeared.
-At this point the car started running rough, at idle, and through acceleration...sputtering uphill, and when climbing through the gears.
-Changed the plugs & wires
-NOW, it's cylinder 5 misfiring, and not nearly as bad. It's idling and running rough, acceleration has somewhat come back, but it's definitely not 100%.
Should I start with the PCV again, since it's not starting after I fill the tank, and climbing gears slow? Is there anything else I should be checking?
I have noticed that if I push gas pedal while turning the corner, especially if starting to go uphill, there is significant vibration felt in the gas pedal. It happens every time, as I use the same road each day, for 6 months now. I recently had a rental prius for a weeks, and had the same experience, although not as pronounced as my car.
View 9 Replies