Santa FE SM (2001-06) :: Balance Shaft Oil Seal Replacement?
Dec 20, 2015
I have a 2001 4 cylinder Santa Fe. And atm I'm trying to replace the balance shaft oil seal but am having major problems getting it out.
View 2 Replies
Dec 20, 2015
Advertisement
Santa FE SM (2001-06) :: AC Compressor Replacement - Shaft Seal Is Leaking
After 9 solid years of service, my a/c compressor finally failed. According to the shop, its leaking at the center seam of the compressor. If the system is charged, then the compressor will operate until the low pressure switch shuts it down. My question is this: Can this compressor be rebuilt? If so, where can I get the parts (I'm assuming the shaft seal is leaking).
Also, a quick search on eBay provides several compressors that fit my car; however, some of them are listed as HS-17 compressors and others are HS-18. My car (according to the A/C sticker on the hood) says I have an HS-18 compressor. Are these two interchangeable? I'm asking because if the current compressor can't be rebuilt, then I will have to buy either a reman. or new unit.
Car: 2002 Hyundai Santa Fe, GLS, 2.7L V6
Santa FE SM (2001-06) :: 2.4L Engine - Crankshaft Oil Seal Replacement
Replacing the crank shaft and camshaft oil seals on a 2001 - 2006 2.4L engine?
I'm in the process of installing a timing belt kit w/water pump, pulleys and all seals. My engine has 190,000 Km with no signs of oil in the timing area, but I figure the oil seal would be worn and or cracked/dried so it would make sense to change them, plus it was included in the kit.
Ford Ranger / B-Series :: 1989 - Tranny Input Shaft Seal Replacement?
I'm replacing my clutch components in my 89 Ranger with an M5OD transmission. While I'm doing it I'm going to replace the input shaft seal on the transmission. I'm looking for the torque specs for the housing that holds the seal.
Also, should there be any play on the input shaft? My transmission has never made any noise but I noticed some slight play in the shaft.
Golf IV / Jetta IV :: 2001 - How To Access The Transmission Input Shaft Seal
I'm trying to get to the manual transmission input shaft seal on my 01 GTI w/12V VR6. I've removed the 3 bolts surrounding the input shaft but the metal shroud underneath the 3 bolts seems to be adhered tightly in place. You can see the 3 bolt holes and metal shroud in this photo: [URL]
Am I on the right track in trying to remove that shroud? If so, how do I loosen it?
Ford - Explorer :: Replace Balance Shaft Chain Tensioner Without Pulling Motor?
I am in the middle of replacing the timing chains on my 1998 4.0L SOHC 4x4 Explorer. I was going to ignore the balance shaft chain but a piece of the broken jackshaft chain tensioner broke the balance shaft chain tensioner too. Now I have to pull the upper pan/ladder frame.
Of course, the manual says I have to pull the motor to remove the upper pan/ladder frame on a 4x4 but I have heard there may be a way around this. How to avoid pulling the motor and still be able to replace the balance shaft chain tensioner?
Ford Super Duty (1999-2016) :: Vibration Starting At 60 MPH / Drive Shaft Balance
I have a vibration starting at 60mph. Its slight but there. I crawled under and found a very shiny rectangle of metal. Safe to assume I flung a shaft weight? It drives perfect around town just at freeway speeds.
View 14 RepliesSanta FE SM (2001-06) :: Code P0340 Cam Shaft Sensor Fault
I have a 2005 crdi diesel santa fe that i have a strange problem with it starts up first time no problem in the mornings and can drive all day long. However if i switch it off and leave it sit for about a half hour no way will it start again until it cools off. It will start though with a push start instantly!
I got only one fault code P0340 cam shaft sensor fault, i replaces sensor and made no difference. Is this a common fault???
Santa FE SM (2001-06) :: Input Shaft Speed Sensor Connector
I have a 2001 Santa Fe GLS 4WD, I've had my Auto Transmission Speed Sensor replaced and will have the output speed sensor replaced to have speedometer/odometer and cruise control fixed. While having the first sensor replaced my mechanic noticed the Input Shaft Speed Sensor Connector (the plug on the wiring harness) was cracked. I've been looking everywhere for this connector. I don't want to buy the complete wiring harness because I've heard it is very expensive. I want just the connector. What is the part number of just the connector?
View 2 RepliesSanta FE SM (2001-06) :: Drive Shaft Failure / Whining Sound
So I own a 2003 Hyundai Santa Fe GLS 2.7. I am the fourth owner and currently there is 168k miles on the vehicle. I purchased the car with around 110k miles on it and have had it for nearly 5 years now.
Aside from general maintenance I have never had a single issue with it, until last weekend. On the way back home from a road trip I began to notice a whining sound, and then very abruptly the car shook and I lost control of the vehicle and had to pull over on the shoulder. I was on the highway and was VERY fortunate to not have gotten into an accident.
After inspecting carefully I discovered my 4WD Drive Shaft was literally hanging by a thread. The knuckles were ruined, and in the process my Transfer Case and Exhaust System were all severely damaged.
Santa FE SM (2001-06) :: Auto Transmission Seal Keeps Blowing
I have a 2002 santa fe v6 all AWD. It has already had a used trans installed about 3 years ago. Just the other day the front main seal in the trans starts pouring. I took it to a transmission guy it cost me about 600 to have one put in it, he said that was the the problem he got it fixed he drove it and it was all good. Get in it driving it home and everything goes fine. Then after about 5 or 6 miles the trans goes crazy, so I am wondering whats up. I get out and look and its out of fluid because the seal done blew back out. I call him he said he fixed it not his problem it worked when it left his shop.S o my question is what would make the seal need replaced again 5 miles down the road is it a torque converter problem, or something in the trans bad, or did the guy just not do it right. He told me to bring it back and he would look at it but I've done spent all i had on it for him to fix it.
View 2 RepliesSanta FE SM (2001-06) :: Transmission Oil Leak On Driveshaft Seal?
I had the abs come on on dry pavement.. I changed the front ring gears,, Bought 2 new axles with ring gears all new on there.. fixed the issue.. Now i have a oil leak--transmission oil at the driver's side axle.. Is that the seal there in the trans that should be replaced? difficult? Why leak now if it wasn't leaking before..
View 5 RepliesSanta FE SM (2001-06) :: 2003 - Front Shaft On Vehicle Right Side Makes A Noise
The bearing supporting the half shaft on the vehicle right side makes a noise. I don't hear the noise in the wheel bearings so I believe the noise is isolated to the support bearing.
The SF has 175k mi. The right side cv axle was replaced and it had some looseness in it but it did not eliminate the noise.
Additionally, I don't discount that some noise is generated by the tires as they are not new.
2003 Santa Fe 6cyl ....
Dodge - Neon :: Leak At Cam Shaft Seal
we have a 97 dodge neon soc that keeps leaking at the cam shaft seal. it has been replaced 3 times now? It keeps working it's way out and leaks oil.
View 1 RepliesPassat (B5) :: Cam Shaft Adjuster Seal Leaking
Passat, 2003, 5 speed, turbo, 1.8T engine, 4 door, 66K miles.
No oil on garage floor and tiny amount of oil at rear of engine, Is this urgent?
(I have had many cars with no seal or gasket issues- especially at 66K).
Ford Excursion :: A/C Shaft Seal Leaking?
Well, the ac in my truck has been less than exciting since I've owned it and its time to address it before another trip.
I crawled under last night to explore the Ac clutch air gap and found that the shaft seal is leaking and clutch is grooved pretty bad and covered in oil.
I'm thinking it's time for a compressor, clutch, orifice tube, expansion valve and reciever/dryer. Does that about sum it up? I haven't messed with AC systems much outside of my simple jeep system that was as easy as two seals and recharge in my garage to fix it.
Do I need to flush the lines out? Should I do that at all? Motor craft worth the cost over something like four seasons? Its almost twice the cost but in the end if something goes I'm further downstream after freon etc to charge it and the possible shop charge if I pay to have to done.
Celica :: 2000 GT - New Output Shaft Seal Leaks
I installed a JDM 2ZZ-GE engine and 6 speed manual trans-axle into my 2000 Celica GT.
I have ran into a interesting problem. I replaced the output shaft seals and now whenever the car is in the air and the suspension is unloaded (the drive axle is pulled slightly from the trans) the drivers side seal leaks a bit of gear oil. The drive axle is snapped into place. Nothing leaks when the car is on the ground.
I did reuse the old drive axles, which had a lot of miles on them but still appeared good and useable. I have been told to replace the new seal because it may be damaged, but I am wondering if it may be that the drive axle end is worn.
I have seen this with harmonic balancers for engines. They even sell a replacement sleeve for harmonic balancers so you can re-use the old worn one.
Ford Transmission :: Small Leak Around Tail Shaft Seal
I got a fmx mated to 351w, trans was on back of a 302 and no problems other than small leak around tail shaft seal but shifted great. Now I decided to install mildly built 351w so figured it'd be a good time to build tranny. Installed after build and immediately it was slipping. Pulled trans out took it back to shop and he said the forward seal was blown. Installed again, after about 15 miles same result! What could be causing this. It is fine in reverse, but slips bad in forward gears.
View 2 RepliesFord Excursion :: Front End Noise - Inner Seal Dangling On Stub Shaft
For what it's worth I have been feeling a bit of a tug for 3 weeks. That's about 150 miles or 5 times driving. Installed new sway bar damper.
Pulling into the driveway the heard a ting, and look to find the inner seal of the hub spinning on the stub shaft!
An exploded view of this front end hub/bearing/brake assembly?
Ford Ranger / B-Series :: 1999 - Output Shaft Seal Won't Stay?
I replaced the seal the other day on my ranger because I noticed my fluid disappearing. Went ahead and changed the filter and fluid as well. Flushed the system, and I go back to my truck tonight and there's a huge puddle of trans fluid. And the output shaft seal is once again, up against the drive shaft. I've spent like $150 on trans fluid since Friday, and $1000+ to get the truck running again last month, so pardon me if I get edgy about her.
99 2.5 auto. I changed the trans pan gasket too. No leaks from it.
Ford Excursion :: Drips Coming From Rear Axle Input Shaft Seal
I have noticed a few drips coming from the rear axle input shaft where the drive shaft connects. It has only done it once and there is no residue on the trailer hitch so I know it didn't dump everything on the road. If change this seal, how difficult is it and do you have any information which might make it easier.
View 14 Replies