I recently purchased a 3.5 V6 Santa fe. The Check engine light keeps going on. I took it to a few shops and I am getting the same code. It is the O2 sensor in bank one. (I think the the code was po170.) The light keeps going on and off. All I can find are the same problems with different Santa Fe engines (2.7, etc. )... My SUV has 100,050 miles on it.
View 1 RepliesI have an 2004 Santa Fe and im having some Mass Air Flow Sensor problems but I dont know what's wrong. My engine light came on for the second time after awhile. And I got it checked for the code and of course it was my sensor again. The first time I just giggled it around and the light went off. I did the same thing today with giggling it again went off. So I feel like it might be a loose connection but I really hope it isn't failing because im pretty sure that's uber expensive to fix.
View 2 RepliesMy engine is in trouble. A few weeks ago, my check engine light came on. The diagnostics revealed that my Mass Airflow Sensor was done for. I replaced it, and everything was working fine for a week. Then a couple of days ago, my Electronic Power Control (EPC) light came on. The car is really dragging. It have to gun it to make it go above 60 MPH. It's become scary to drive on highways. Are the two issues potentially connected?
View 1 RepliesMy '04 santa fe 3.5 v6 gls/lx, 79k miles, gas, auto, check light has just come on while I was driving a less than 10 mile journey. How can I check what is wrong. Do I need some sort of diagnostic code checker. Do any national outlets check it for free (Pep Boys or Auto Zone, etc).
Just 5 days ago (about 50 miles only) I had timing belt, water pump, plugs and leads replaced, brakes checked and lubes flushed; BUT not at above dealers. I would rather know what the code is saying before I go back to the shop who carried out the work.
How can i turn off check engine light (hyundai santa fe 2003 3.5) by fuse ? I do not have any code scanner.
View 10 RepliesSanta Fe 2001 2.4l. How can I check or test a MAF sensor? I replaced the sensor four months ago but now I have the P0102 error code again. I would like to have recommendations before to clean it or replace it again.
View 4 RepliesI have had a check engine light go on and off with P0700 and P0741 but since the flush day 3 it hasnt come back on and it was chucking with rpm doing small jumps... but now it does it in the mornings after sitting all night after a few chucks its fine for the rest of the day til the next day no check engine light so far, but transmission flush has worked a lot not as bad as before the flush.. So what else could be causing it? Its a 2006 hyundai santa fe with 274,000 kms.
View 24 RepliesI have A 2001 Santa Fe. The check engine light came on about 3 weeks ago and the car was still running fine up until the last few days it felt a little sluggish. Today I got a little muffled backfire noise. It was like a putting noise if I pushed on the gas to hard to speed up. The car has 95,000 miles on it.The car starts up with no problems and doesn't stall. Its A 6 cylinder All wheel drive vehicle.
View 10 RepliesCheck engine light on, car stalled once. Pulling code p0320 "Engine Speed Input Circuit Malfunction." Tachometer works intermittently. Where do I start?
View 2 RepliesRecently got check engine light fault code p0320
2005 3.5 with 172k miles
I have a 2002 SF GLS/LX (?) with 2.7 L V6 2WD (60,000 miles) and it started to apply the ABS brakes in a random manner. Found out it was caused by a broken front wheel tone ring. So, I pulled the ABS fuse under the dash and it stopped the brake problem. Drove it today to pick up some wood and now the check engine light has come on.
My neighbor has an OBD scanner and he plugged it in and said I have a P0501 code and a P1529 code, but he didn't know what they meant. What they mean and are they related to me pulling the fuse under the dash? Did I pull the wrong fuse? Is there another fuse somewhere that I should have pulled?
My 2002 Hyundai Santa Fe 2.7L V6 AWD failed to start a week ago. After towing to my neighborhood repair shop, it was diagnosed as a faulty ECM based on code P560 (System Voltage Problem). They replaced the ECM (along with relay) with a used one with the exact same part#. After that, the car was started and run OK but Check Engine Light stays on all the time. The codes displayed are:
P1529 TCU MIL Request Signal
P0501 VSS Range Performance
I was told that this is caused by the fact that each ECM is VIN/PIN locked. The replacing ECM was used in another car before and was locked with a different VIN thus cannot communicate with some components of the current car.
My questions are:
Can this used ECM be unlocked and relocked with a new VIN/PIN? If so, does it require the previous VIN/PIN to unlock? Most likely the previous VIN/PIN is no longer available.
Does this service require the presence of the car or can it be done with the ECM alone? Do keys need to be re-registered? The car starts fine currently.
I jump started my santafe becouse the battery was weak. After it started the check engine light on the dashboard came on and it stays on. What could the problem be.
View 1 RepliesMy wife's car is throwing at p0306 code. I have changed the park plugs and the check engine lights comes on after 5-10 minute of driving and gives the same code. Can I move the spark plug wire to another ignition coil bank to test the coil? The picture shows the current plug locations on the ignition pack. Is there any certain order they need to be in or can I just swap 6 and 5 since they are the closest together?
View 6 RepliesI have a 2004 Santa Fe 2.4L the check engine light is on and says about the evap canister solenoid. I am trying to located it but I can't find it. So, where would it be located at so I can take it apart and where is the Canister located as well...
View 1 RepliesMy check engine light came on the other day and the code stated the the "throttle position is open" so after researching and everyone telling me that i need to change the sensor. I did everything after was fine running better but today only after 3 days replacing it i get the same problems. car has no get up and go hardly can push to 20 mph and when in idle i press the break it starts to bog down and almost want to shut off! and can be really loud...
Santa fe 05' 3.5L ....
I have a 2004 santa fe with a 2.7 v6. I have had a little misfire issue lately. I had a major power loss with a check engine light on it lasted for just a minute before it settled itself out. Had the code pulled at a local parts store. P0301 so I checked the plugs and they looked worn out. I pulled the upper intake and replaced the plugs and wires plus the upper intake gasket. I cleared the code and that seemed to correct the problem. Two days later, same thing happened. The engine seems to be running fine now. I wiggled the wiring harness to the injector and to the coil, no change in the way it runs. I was thinking it could be an injector or a coil pack.
View 6 Replies2002 Santa Fe, 2.7 AWD
The transmission has started going into limp mode and causing the check engine light to come on.
The codes given are p0750 and.... I think p0751, for shift solenoids C and D. There is also the generic Transmission Control Module code.
Limp mode only occurs at higher speeds although shifting feels a little rough at times in lower speeds.
If operated in manual mode the vehicle can be driven normally at all speeds without going into limp mode.
Fluid levels are fine.
With limp mode occurring in automatic but not occurring in manual mode, is it more reasonable to believe the solenoids are malfunctioning or the control module itself? I'm inclined to replace the solenoids but find it odd that the vehicle operates normally in manual. Also, can the solenoids be replaced without removing the transmission? It looks like I could get the pan off but am unsure if there is room to get the work done once it is removed.
Elantra GT 2003 ... I had engine check light on and OBD 2 code reader showed DTC P1529 and P0705. I erased the codes to see if they comes back and one month later I have same codes back. P0705 indicates Transmission Range Sensor Circuit Malfunction, so probably I should check range sensor. How the range sensor looks alike and where to find it. Where can I find it?
View 1 RepliesI have a 06 chevy 3500 express van with a 6.0 engine. The engine light came on about the O2 sensor bank 1 sensor 1 and bank 2 sensor 1 came up on the on the scan tool. It run great. how do I fix it
View 4 RepliesI had a check engine light pop up and I went and got it checked out. Comes to be its a IAT sensor or bad connection with this sensor. I change the sensor and made sure the wires on it is all good. The question is, I still have the check engine light up, does the code need to be deleted? And what happens if the code gets deleted and problem is not fixed?
View 3 Replies